Comments (24)
You need to yaw left and hold it for more than 2 seconds for the menu to pop up. Quad must be disarmed of course.
from kiss_osd.
from kiss_osd.
from kiss_osd.
Ok on v2.5 and kiss v2 installing OSD configuration works. I used my transmitter it worked fine, saved the configuration. I then loaded the OSD that took plugged back in the port 2. When it starts up it shows the FC is armed when the arm switch isn't In arm position and says FC connection??? I checked all the wires have continuity I even tried switcing the tx and Rx wires and nothing I'm stumped I don't get it? It should of worked since I could program it just before I flashed the OSD hex.
from kiss_osd.
Unplug both ports from the PDB and try flashing it again.
from kiss_osd.
from kiss_osd.
The SteelePDB does work with the V2, there are many users that are running that combination. Did you check in the KISS GUI if you have ESC telemetry? Connect USB to FC, run KISS GUI, connect a Lipo (props off) and go in the advanced tab. On the drop down you can display the various ESC telemetry items such as mah, rpm, etc. Please double check that is working properly.
from kiss_osd.
from kiss_osd.
If you do not have any telemetry in the KISS GUI, then you might have a short somewhere on your ESC telemetry. Disconnect the telemetry wire for each ESC one by one and keep checking in the KISS GUI if you get ESC telemetry for the ESCs that are still connected. That might help to narrow down the culprit.
from kiss_osd.
from kiss_osd.
No, the telemetry wires are connected to the FC. FC reads ESC telemetry. OSD reads telemetry (stick input, etc.) from FC.
from kiss_osd.
from kiss_osd.
I don't. You can ask ImpulseRC, but I highly doubt they will give you the board design showing all the traces. All you should need is the pictures on their website:
https://impulserc.com/collections/pdbs/products/mr-steele-alien-pdb-kit-for-kiss-with-osd-and-mic
from kiss_osd.
from kiss_osd.
Try changing arm to AUX1 or AUX2 - that has helped some other users
from kiss_osd.
from kiss_osd.
Hi, same problem here. Kiss V2, and mr Steel PDB. Arming on AUX1 or AUX2 didnt work for me. Also dont have telemetry for ESC on KISS GUI, but i can see telemetry of ESC on OSD.
Same as S-T-A, i cant access the OSD menu by holding yaw on left.
I think there is some kind of incompatibility. Hope you can find and solve it quickly :-)
Meanwhile... any other ideas or workarounds?
from kiss_osd.
Disable level mode
from kiss_osd.
thanks! worked for me!
from kiss_osd.
from kiss_osd.
If the ESC telemetry does not work in the KISS GUI you most probably have a short on one of the ESC telemetry wires (they are internally connected together on the KISS FC). As I suggested before, try disconnecting the telemetry wires one by one to find the issue.
I would recommend you to use a switch or better a knob on your radio to control how many OSD items are displayed - especially useful for the ESC telemetry which you do not need to see all the time. In my wiki check out the section "Making your OSD more or less busy", link is below.
https://github.com/awolf78/KISS_OSD/wiki#setup-of-kiss-osd
from kiss_osd.
from kiss_osd.
Did you check the pins on the KISS FC and PDB? If those are not bent either, then I would talk to your dealer about it. It has nothing to do with the OSD FW - if the FC does not receive telemetry from the ESCs it cannot send it to the OSD and the OSD cannot display it. And since you cannot see the ESC telemetry in the KISS GUI the issue is on the ESC<>FC side.
from kiss_osd.
from kiss_osd.
Related Issues (20)
- Polulu FTDI drivers installation not working HOT 3
- GPS Arrow with mr Steele pdb HOT 2
- AIKON 4 in 1 current sensor is not working on micro minim OSD HOT 4
- No Video Feed No OSD HOT 4
- Steele PDB - No connection to FC HOT 2
- Req: Digital font. HOT 10
- KISS OSD and new KISS V2 Firmware RC36i Camera Control Issue HOT 8
- icons HOT 1
- No connection to Kiss FC w/ steele pdb (Kiss FC V1) HOT 2
- Setting VTX Power via OSD (Wolf PDB with KISS FC v1) HOT 5
- Mr. Steele pdb props all over screen HOT 3
- Correct settings for rssi Steele pdb HOT 6
- mr steele pdb HOT 2
- No Display menu option in OSD menu HOT 5
- No connection to kiss fc HOT 5
- Steele pdb V1 impossible to update firmware HOT 3
- Xloader upload failed HOT 2
- No Mah drawn on OSD HOT 4
- All motors spinning in the same direction (right) HOT 2
- missing SET ITEMSfrom my config menu HOT 1
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from kiss_osd.