Comments (14)
@GuidoHaase the plugin was never finished, i don't own the hardware, and previous reporters failed to provide enough information to finish the plugin.
i've grabbed output of your commands, and added to unit test. so the parser is there.
see 9fd0697...46f08a5
however not sure how it would behave with multiple virtual disks. could you provide create two virtual disks and provide output from mvcli?
6f72349: parses just VD and if status is not functional
will trigger CRITICAL. don't have other test data to handle other values.
from nagios-plugin-check_raid.
Only my soft RAID (Intel ICH) device is detected :
sloeuillet@Domicile:~/dev/GIT$ /home/sloeuillet/check_raid.pl -l
lsscsi
mdstat
sloeuillet@Domicile:~/dev/GIT$ /home/sloeuillet/check_raid.pl -p mdstat
OK: mdstat:[md125(643.21 GiB raid1):UU, md126(102.00 GiB raid1):UU, md127(5.16 MiB):]
sloeuillet@Domicile:~/dev/GIT$ /home/sloeuillet/check_raid.pl -p lsscsi
No RAID configuration found (tried: lsscsi)
from nagios-plugin-check_raid.
lsscsi is not real plugin, but what check_raid plugin you expect to be used for your system? also, read contributing.md, you should run check_raid via -d to capture commands and outputs it runs.
from nagios-plugin-check_raid.
i will have to close this with no resolution if you don't provide more information! can't even figure out which plugin this applies!
from nagios-plugin-check_raid.
lsscsi
plugin is used by hpsa/cciss plugin. do you have appropriate userspace tools installed? hpsa uses cciss_vol_status
from nagios-plugin-check_raid.
Interested too in Marvell Support @glensc
The Marvell raid controllers use a userspace tool "mvcli", by default installed as "/opt/marvell/storage/cli/mvcli"
RPMs available fi from www datoptic.com/Download/LINUXMSU4.1.0.2019.rar
Tested on Centos 7.1, EL7.x installs need a workaround, "modprobe sg" (scsi_generic) needs to be run on time bevor mvcli, otherwise mvcli finds no devices. See RH Relnote "sg3_utils component, BZ#1186462".
[root@ovirt ~]# cat marvell.scr
info -o BLK
smart -p 2
smart -p 3
exit
[root@ovirt ~]# cat marvell.scr | /opt/marvell/storage/cli/mvcli
CLI Version: 4.1.0.9 RaidAPI Version: 5.0.0.1024
Welcome to Marvell RAID Command Line Interface.
> info -o BLK
Block Information
-----------------
Block id: 0
PD id: 2
VD id: 0
Block status: assigned
Size: 29977152 K
Starting offset: 16384 K
Block id: 4
PD id: 3
VD id: 0
Block status: assigned
Size: 29977152 K
Starting offset: 16384 K
> smart -p 2
Smart Info
ID Attribute Name Current Worst Threshhold RawValue
01 Read Error Rate 100 100 0 000000000000
05 Reallocated Sectors 100 100 0 000000000000
09 Power-On Hours Count 100 100 0 0000000005AC
0C Power Cycle Count 100 100 0 00000000000C
AB Unknown 100 100 0 000000000000
AC Unknown 100 100 0 000000000000
AD Unknown 100 100 0 000000000006
AE Unknown 100 100 0 000000000004
B4 Unused Reserved Block 0 0 0 00000000086F
B7 SATA Downshift Error 100 100 0 000000000000
B8 End-to-End error 100 100 0 000000000000
BB Reported Uncorrectable 100 100 0 000000000000
C2 HDA temperature 44 23 0 000000000038
C4 Reallocation count 100 100 0 000000000010
C5 Current pending 100 100 0 000000000000
C6 Offline scan wrong 100 100 0 000000000000
C7 UDMA CRC error rate 100 100 0 000000000000
CA Address Mark errors 100 100 0 000000000000
CE Flying height 100 100 0 000000000000
D2 Vibration During Write 100 100 0 000000000000
F6 Invalid 100 100 0 0000000042F0
F7 Invalid 100 100 0 000000007E33
F8 Invalid 100 100 0 000000009711
> smart -p 3
Smart Info
ID Attribute Name Current Worst Threshhold RawValue
01 Read Error Rate 100 100 0 000000000000
05 Reallocated Sectors 100 100 0 000000000000
09 Power-On Hours Count 100 100 0 0000000005AC
0C Power Cycle Count 100 100 0 00000000000C
AB Unknown 100 100 0 000000000000
AC Unknown 100 100 0 000000000000
AD Unknown 100 100 0 000000000007
AE Unknown 100 100 0 000000000004
B4 Unused Reserved Block 0 0 0 00000000086F
B7 SATA Downshift Error 100 100 0 000000000000
B8 End-to-End error 100 100 0 000000000000
BB Reported Uncorrectable 100 100 0 000000000000
C2 HDA temperature 75 21 0 000000000019
C4 Reallocation count 100 100 0 000000000010
C5 Current pending 100 100 0 000000000000
C6 Offline scan wrong 100 100 0 000000000000
C7 UDMA CRC error rate 100 100 0 000000000000
CA Address Mark errors 100 100 0 000000000000
CE Flying height 100 100 0 000000000000
D2 Vibration During Write 100 100 0 000000000000
F6 Invalid 100 100 0 000000006328
F7 Invalid 100 100 0 000000000C9F
F8 Invalid 100 100 0 000000003FDF
> exit
from nagios-plugin-check_raid.
looks like need to create new plugin from scratch named mvcli
from nagios-plugin-check_raid.
Great @glensc, let me know if there is something i can test! THX a lot
from nagios-plugin-check_raid.
does mvcli
accept those commands via commandline as well? it would be easier to script that way than just STDIN stream
from nagios-plugin-check_raid.
I will have a look
from nagios-plugin-check_raid.
@olidietzel did you had look?
anyway, there's WIP plugin in repo:
lib/App/Monitoring/Plugin/CheckRaid/Plugins/mvcli.pm
from nagios-plugin-check_raid.
Hi @glensc,
I'm trying to use check_raid but don't get some RAID controller related output from the tool. Here are some informations about my environment (Debian 9.2.1 Stretch with Proxmox VE on HP Microserver Gen10 X3421) and check_raid 4.0.8 (2017-09-01):
# uname -a
Linux zeus 4.13.8-2-pve #1 SMP PVE 4.13.8-28 (Wed, 29 Nov 2017 09:49:35 +0100) x86_64 GNU/Linux
# lspci | grep -i marvell
01:00.0 SATA controller: Marvell Technology Group Ltd. 88SE9230 PCIe SATA 6Gb/s Controller (rev 11)
# dmesg | grep -i marvell
[ 2.050088] ata9.00: ATAPI: MARVELL VIRTUAL, 1.09, max UDMA/66
[ 2.104320] ata2.00: ATA-7: MARVELL Raid VD, MV.R00-0, max UDMA7
[ 2.104986] scsi 1:0:0:0: Direct-Access ATA MARVELL Raid VD 00-0 PQ: 0 ANSI: 5
[ 2.140748] scsi 8:0:0:0: Processor Marvell Console 1.01 PQ: 0 ANSI: 5
# /bin/mvcli
SG driver version 3.5.36.
CLI Version: 4.1.0.30 RaidAPI Version: 5.0.0.1067
Welcome to RAID Command Line Interface.
# /bin/mvcli info -o blk
SG driver version 3.5.36.
Block Information
-----------------
Block id: 0
PD id: 0
VD id: 0
Block status: assigned
Size: 3906936640 K
Starting offset: 16384 K
Block id: 4
PD id: 1
VD id: 0
Block status: assigned
Size: 3906936640 K
Starting offset: 16384 K
# /bin/mvcli info -o vd
SG driver version 3.5.36.
Virtual Disk Information
-------------------------
id: 0
name: VD0
status: functional
Stripe size: 64
RAID mode: RAID1
Cache mode: Not Support
size: 3815367 M
BGA status: not running
Block ids: 0 4
# of PDs: 2
PD RAID setup: 0 1
Running OS: yes
Total # of VD: 1
# /bin/mvcli smart -p 0
SG driver version 3.5.36.
SMART STATUS RETURN: OK.
Smart Info
ID Attribute Name Current Worst Threshhold RawValue Status
01 Read Error Rate 200 200 51 000000000000 OK
03 Spin-Up Time 188 184 21 0000000015D7 OK
04 Start/Stop Count 100 100 0 000000000021 OK
05 Reallocated Sectors 200 200 140 000000000000 OK
07 Seek Error Rate 200 200 0 000000000000 OK
09 Power-On Hours Count 100 100 0 000000000023 OK
0A Spin Retry Count 100 253 0 000000000000 OK
0B Calibration retry 100 253 0 000000000000 OK
0C Power Cycle Count 100 100 0 000000000021 OK
C0 Power-off retract 200 200 0 00000000000C OK
C1 Load/Unload cycle 200 200 0 000000000026 OK
C2 HDA temperature 121 117 0 00000000001D OK
C4 Reallocation count 200 200 0 000000000000 OK
C5 Current pending 200 200 0 000000000000 OK
C6 Offline scan wrong 100 253 0 000000000000 OK
C7 UDMA CRC error rate 200 200 0 000000000000 OK
C8 Write error rate 100 253 0 000000000000 OK
And some check_raid output (run from cmd line as root for testing only):
# ./check_raid -d
check_raid 4.0.8
Visit <https://github.com/glensc/nagios-plugin-check_raid#reporting-bugs> how to report bugs
Please include output of **ALL** commands in bugreport
DEBUG EXEC: /sbin/dmsetup status --noflush at ./check_raid line 484.
DEBUG EXEC: /proc/mdstat at ./check_raid line 484.
DEBUG EXEC: /bin/mvcli at ./check_raid line 484.
./check_raid --plugin=mvcli -d
check_raid 4.0.8
Visit <https://github.com/glensc/nagios-plugin-check_raid#reporting-bugs> how to report bugs
Please include output of **ALL** commands in bugreport
DEBUG EXEC: /bin/mvcli at ./check_raid line 484.
#./check_raid --plugin=mvcli
<no answere>
./check_raid --plugin=mvcli --plugin-option='mvcli blk'
<no answere>
./check_raid --plugin=mvcli --plugin-option='mvcli smart'
<no answere>
./check_raid --plugin=mvcli --plugin-option='info -o blk'
<no answere>
./check_raid --plugin=mvcli --plugin-option='smart -p 0'
<no answere>
Actually I'd just like to get an information if the RAID1 is working fine or demaged. But, so far, I don't get any reply from check_raid. Am I doing s.th. wrong? Do you need more information(s)? Anyway, thanks for building this plug-in!
from nagios-plugin-check_raid.
Hi @glensc,
thanks for your feedback and modifying the parser!
I'll provide a few more input strings for mvcli to test the parser soon. Please note, there are also two strings which don't work on RAID[0|1]. I'll add them too just for let you know and for testing.
however not sure how it would behave with multiple virtual disks. could you provide create two virtual disks and provide output from mvcli?
I'll do as you suggested soon. But, first I'll have to dive in my hw grove looking for two equal or most similar drives ;-)
6f72349: parses just VD and if status is not functional will trigger CRITICAL. don't have other test data to handle other values.
As far as I remember there are more states availalbe, like 'rebuilding' including %, 'paused', etc.. I'll have a look at home and we'll share the result with you here.
Please allow a few days for feedback - I'm working on it. Thanks!
from nagios-plugin-check_raid.
Hi @glensc,
here are some more data from the marvell raid controller.
As suggested by you I added two more (old) drives and built a further VD running as RAID1.
First, have a look at the mvcli commands:
# mvcli ?
SG driver version 3.5.36.Legend:
[options] - the options within [] are optional.
<x|y|z> - choose one of the x, y or z.
[<x|y|z>] - choose none or one of the x, y or z.Abbreviation:
VD - Virtual Disk, Array - Disk Array
PD - Physical Disk, BGA - BackGround ActivityType '-output [filename]' to output to a file.
Type 'help' to display this page.
Type 'help command' to display the help page of 'command'.
Type 'command -h' to display help for 'command'.Command name is not case sensitive and may be abbreviated if the
abbreviation is unique. Most commands support both short (-) and
long (--) options.Long option names may be abbreviated if the abbreviation
is unique. A long option may take a parameter of the form '--arg=param'
or '--arg param'. Option name is case sensitive, option parameter is not.COMMAND BRIEF DESCRIPTION
? :Get brief help for all commands.
help :Get brief help for all commands or detail help for one command.
rebuild :Start, stop, pause, resume rebuilding VD.
smart :Display the smart info of physical disk.
flash :Update, backup or erase flash image and erase hba or pd page.
enc :Get enclosure, enclosure element or enclosure config information.
adapter :Default adapter the following CLI commands refers to.
rescan :Rescan the adapters
create :Create virtual disk.
delete :Delete virtual disk or spare drive.
event :Get the current events.
get :Get configuration information of VD, PD, Array, HBA or Driver.
info :Display adapter(hba), virtual disk(vd), disk array,
physical disk(pd), Port multiplexer(pm), expander(exp),
block disk(blk) or spare drive information.
set :Set configuration parameters of VD, PD or HBA.
import :Import a virtual disk.
locate :Locate the specified PD.
report :report a conflicted virtual disk to OS.
devmap :Map device ID to device magic number in the OS.
Now following the output of mvcli running with 2 RAID1 VDs and 4 drives:
# mvcli info -o blk
SG driver version 3.5.36.
Block InformationBlock id: 0
PD id: 0
VD id: 0
Block status: assigned
Size: 3906936640 K
Starting offset: 16384 KBlock id: 4
PD id: 1
VD id: 0
Block status: assigned
Size: 3906936640 K
Starting offset: 16384 KBlock id: 8
PD id: 2
VD id: 1
Block status: assigned
Size: 244116608 K
Starting offset: 16384 KBlock id: 12
PD id: 3
VD id: 1
Block status: assigned
Size: 244116608 K
Starting offset: 16384 K
# mvcli info -o hba
SG driver version 3.5.36.
Adapter ID: 0
Product: 1b4b-9230
Sub Product: 1b4b-9230
Chip revision: A1
slot number: 0
Max PCIe speed: 5Gb/s
Current PCIe speed: 5Gb/s
Max PCIe link: 2
Current PCIe link: 2
BIOS version: 1.0.0.1028
Firmware version: 2.3.0.1078
Boot loader version: 2.1.0.1009
# of ports: 4
Buzzer: Not supported
Supported port type: SATA
Supported RAID mode: RAID0 RAID1 RAID10 hc(hypper capacity) hs(hypper safe)
Maximum SSD in one HyperDuo: 3
Maximum SSD Segment: 3
Maximum disk in one VD: 4
PM: Supported
Expander: Not supported
Rebuild: Supported
Background init: Not supported
Sync: Not supported
Migrate: Not supported
Media patrol: Not supported
Foreground init: Not supported
Copy back: Not supported
Maximum supported disk: 7
Maximum supported VD: 4
Max total blocks: 128
Features: rebuild
Advanced features: event sense code,multi VD,spc 4,image health,timer,smart poll,bga rate,ata pass through,remap,access register
Max buffer size: 3
Stripe size supported: 32K 64K
Image health: Healthy
Autoload image health: Healthy
Boot loader image health: Healthy
Firmware image health: Healthy
Boot ROM image health: Healthy
HBA info image health: Healthy
# mvcli info -o pd
SG driver version 3.5.36.
Physical Disk Information
Adapter: 0
PD ID: 0
Type: SATA PD
Linked at: HBA port 0
Size: 3907018584 K
Write cache: not supported
SMART: supported (on)
NCQ: supported (on)
48 bits LBA: supported
supported speed: 1.5 3 6 Gb/s
Current speed: 6 Gb/s
model: WDC WD40EFRX-68N32N0
Serial: WD-WCC7K5KD3PFS
Firmware version: 82.00A82
Locate LED status: Not Support
Running OS: yes
block ids: 0
associated VDs: 0
PD valid size: 0 KAdapter: 0
PD ID: 1
Type: SATA PD
Linked at: HBA port 1
Size: 3907018584 K
Write cache: not supported
SMART: supported (on)
NCQ: supported (on)
48 bits LBA: supported
supported speed: 1.5 3 6 Gb/s
Current speed: 6 Gb/s
model: WDC WD40EFRX-68N32N0
Serial: WD-WCC7K5KD3TSY
Firmware version: 82.00A82
Locate LED status: Not Support
Running OS: yes
block ids: 4
associated VDs: 0
PD valid size: 0 KAdapter: 0
PD ID: 2
Type: SATA PD
Linked at: HBA port 2
Size: 244198584 K
Write cache: not supported
SMART: supported (on)
NCQ: supported (on)
48 bits LBA: supported
supported speed: 1.5 3 Gb/s
Current speed: 3 Gb/s
model: VB0250EAVER
Serial: 6VMVE70A
Firmware version: HPG0
Locate LED status: Not Support
Running OS: no
block ids: 8
associated VDs: 1
PD valid size: 0 KAdapter: 0
PD ID: 3
Type: SATA PD
Linked at: HBA port 3
Size: 244198584 K
Write cache: not supported
SMART: supported (on)
NCQ: supported (on)
48 bits LBA: supported
supported speed: 1.5 3 Gb/s
Current speed: 3 Gb/s
model: VB0250EAVER
Serial: 6VMVC03W
Firmware version: HPG0
Locate LED status: Not Support
Running OS: no
block ids: 12
associated VDs: 1
PD valid size: 0 KTotal # of PD: 4
# mvcli info -o vd # VD1 degraded and rebuilding paused
SG driver version 3.5.36.Virtual Disk Information
id: 0
name: VD0
status: functional
Stripe size: 64
RAID mode: RAID1
Cache mode: Not Support
size: 3815367 M
BGA status: not running
Block ids: 0 4
# of PDs: 2
PD RAID setup: 0 1
Running OS: yesid: 1
name: VD1
status: degraded
Stripe size: 64
RAID mode: RAID1
Cache mode: Not Support
size: 238395 M
BGA status: paused
Block ids: 8 12
# of PDs: 2
PD RAID setup: 2 3
Running OS: no
BGA progress: rebuilding is paused at 0%Total # of VD: 2
# mvcli info -o vd # VD1 degraded and rebuilding working
SG driver version 3.5.36.Virtual Disk Information
id: 0
name: VD0
status: functional
Stripe size: 64
RAID mode: RAID1
Cache mode: Not Support
size: 3815367 M
BGA status: not running
Block ids: 0 4
# of PDs: 2
PD RAID setup: 0 1
Running OS: yesid: 1
name: VD1
status: degraded
Stripe size: 64
RAID mode: RAID1
Cache mode: Not Support
size: 238395 M
BGA status: running
Block ids: 8 12
# of PDs: 2
PD RAID setup: 2 3
Running OS: no
BGA progress: rebuilding is 2% doneTotal # of VD: 2
# mvcli smart -p 0
SG driver version 3.5.36.
SMART STATUS RETURN: OK.Smart Info
ID Attribute Name Current Worst Threshhold RawValue Status
01 Read Error Rate 200 200 51 000000000000 OK
03 Spin-Up Time 207 171 21 000000001208 OK
04 Start/Stop Count 100 100 0 000000000028 OK
05 Reallocated Sectors 200 200 140 000000000000 OK
07 Seek Error Rate 100 253 0 000000000000 OK
09 Power-On Hours Count 100 100 0 000000000046 OK
0A Spin Retry Count 100 253 0 000000000000 OK
0B Calibration retry 100 253 0 000000000000 OK
0C Power Cycle Count 100 100 0 000000000028 OK
C0 Power-off retract 200 200 0 00000000000F OK
C1 Load/Unload cycle 200 200 0 00000000002B OK
C2 HDA temperature 121 117 0 00000000001D OK
C4 Reallocation count 200 200 0 000000000000 OK
C5 Current pending 200 200 0 000000000000 OK
C6 Offline scan wrong 100 253 0 000000000000 OK
C7 UDMA CRC error rate 200 200 0 000000000000 OK
C8 Write error rate 100 253 0 000000000000 OK
# mvcli smart -p 1
SG driver version 3.5.36.
SMART STATUS RETURN: OK.Smart Info
ID Attribute Name Current Worst Threshhold RawValue Status
01 Read Error Rate 200 200 51 000000000000 OK
03 Spin-Up Time 205 171 21 00000000126C OK
04 Start/Stop Count 100 100 0 000000000028 OK
05 Reallocated Sectors 200 200 140 000000000000 OK
07 Seek Error Rate 200 200 0 000000000000 OK
09 Power-On Hours Count 100 100 0 000000000045 OK
0A Spin Retry Count 100 253 0 000000000000 OK
0B Calibration retry 100 253 0 000000000000 OK
0C Power Cycle Count 100 100 0 000000000028 OK
C0 Power-off retract 200 200 0 000000000010 OK
C1 Load/Unload cycle 200 200 0 00000000002A OK
C2 HDA temperature 121 117 0 00000000001D OK
C4 Reallocation count 200 200 0 000000000000 OK
C5 Current pending 200 200 0 000000000000 OK
C6 Offline scan wrong 100 253 0 000000000000 OK
C7 UDMA CRC error rate 200 200 0 000000000000 OK
C8 Write error rate 100 253 0 000000000000 OK
# mvcli smart -p 2
SG driver version 3.5.36.
SMART STATUS RETURN: OK.Smart Info
ID Attribute Name Current Worst Threshhold RawValue Status
01 Read Error Rate 111 99 6 000000004F09 OK
03 Spin-Up Time 97 97 0 000000000000 OK
04 Start/Stop Count 100 100 20 0000000000E9 OK
05 Reallocated Sectors 100 100 36 000000000001 OK
07 Seek Error Rate 74 60 30 00000000DEFC OK
09 Power-On Hours Count 66 66 0 000000007507 OK
0A Spin Retry Count 100 100 97 000000000000 OK
0C Power Cycle Count 100 100 20 000000000076 OK
B4 Used Reserved Block(Total) 100 100 0 00000000FFFF OK
B7 SATA Downshift Error 100 100 0 000000000000 OK
B8 End-to-End error 100 100 97 000000000000 OK
BB Reported Uncorrectable 100 100 0 000000000000 OK
BC Command Timeout 100 99 0 000000000005 OK
BD High Fly Writes 100 100 0 000000000000 OK
BE Temperature Diff 66 59 45 000000000022 OK
C2 HDA temperature 34 41 0 000000000022 OK
C3 ECC recovered 53 38 0 000000004F09 OK
C4 Reallocation count 100 100 36 000000000001 OK
C5 Current pending 100 100 0 000000000000 OK
C6 Offline scan wrong 100 100 0 000000000000 OK
C7 UDMA CRC error rate 200 200 0 000000000000 OK
# mvcli smart -p 3
SG driver version 3.5.36.
SMART STATUS RETURN: OK.Smart Info
ID Attribute Name Current Worst Threshhold RawValue Status
01 Read Error Rate 117 99 6 0000000015F1 OK
03 Spin-Up Time 97 97 0 000000000000 OK
04 Start/Stop Count 100 100 20 0000000000E9 OK
05 Reallocated Sectors 100 100 36 000000000000 OK
07 Seek Error Rate 74 60 30 000000009DC4 OK
09 Power-On Hours Count 66 66 0 0000000074FB OK
0A Spin Retry Count 100 100 97 000000000000 OK
0C Power Cycle Count 100 100 20 000000000076 OK
B4 Used Reserved Block(Total) 100 100 0 00000000FFFF OK
B7 SATA Downshift Error 100 100 0 000000000000 OK
B8 End-to-End error 100 100 97 000000000000 OK
BB Reported Uncorrectable 100 100 0 000000000000 OK
BC Command Timeout 100 97 0 000000000085 OK
BD High Fly Writes 100 100 0 000000000000 OK
BE Temperature Diff 68 60 45 000000000020 OK
C2 HDA temperature 32 40 0 000000000020 OK
C3 ECC recovered 59 36 0 0000000015F1 OK
C4 Reallocation count 100 100 36 000000000000 OK
C5 Current pending 100 100 0 000000000000 OK
C6 Offline scan wrong 100 100 0 000000000000 OK
C7 UDMA CRC error rate 200 200 0 000000000000 OK
# mvcli info -o spare
SG driver version 3.5.36.
Spare Disk InformationPD id: 0
Status: none sparePD id: 1
Status: none sparePD id: 2
Status: none sparePD id: 3
Status: none spare
Commands not supported by "my" adapter:
# mvcli info -o array
SG driver version 3.5.36.
-o : array is not supported on this adapter
# mvcli info -o exp
SG driver version 3.5.36.
Expander is not supported on adapter 0.
# mvcli info -o pm
SG driver version 3.5.36.
No port multiplexer is found.
Commands with option "get":
# mvcli get -o VD
SG driver version 3.5.36.
virtual disk id: 0
cache mode: Not supportvirtual disk id: 1
cache mode: Not support
# mvcli get -o PD
SG driver version 3.5.36.
hard disk id: 0
write cache: not support
drive speed: 6 Gb/shard disk id: 1
write cache: not support
drive speed: 6 Gb/shard disk id: 2
write cache: not support
drive speed: 3 Gb/shard disk id: 3
write cache: not support
drive speed: 3 Gb/s
# mvcli get -o HBA
SG driver version 3.5.36.
HBA Index: 0
Auto Rebuild: not support
Rebuild Rate: 50
Raw Update: on
I hope this will be usefull for further development of the mvcli.pm .
Greetinx
Guido
from nagios-plugin-check_raid.
Related Issues (20)
- arcconf: bbu monitoring for flash+battery/supercap adaptec modules HOT 1
- arcconf: doesn't handle logical device status: Impacted (Build/Verify with fix : 90 %) HOT 2
- Allow to ignore plugins
- No remote servers RAID status: check_raid UNKNOWN HOT 16
- Possible to hide "OK" results or just showing "OK" and not all devices? HOT 4
- Error runing plug-in on debian 10 HOT 10
- remote monitor HOT 1
- Use of StorCli instead of MegaCli HOT 5
- [bug] with parsing mdadm output => Unexpected parse
- Sudo error on centos
- WARNING: megacli:[Volumes(1): DISK0.0:Optimal, WriteCache:DISABLED HOT 2
- arcconf: parse error HOT 6
- Unexpected parse at ./check_raid.pl line 3578, <$fh> line 6. HOT 1
- HP ssacli - consider predictive failure information HOT 6
- HP ssacli - rebuilding shouldn't perhaps still be warning state? HOT 6
- HP ssacli -
- Error with P440AR RAID controller. How to solve, what to change? Please advice. HOT 6
- "NOT PARSED" and "Can't locate object method" errors HOT 2
- Feature Request mdstat: Warn when auto-read-only array detected
- "sudo: a password is required" on Ubuntu 20.0.4 HOT 4
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from nagios-plugin-check_raid.