Modules on QCC300x chips

[kiterservice]

Modules on QCC300x chips

[kiterservice]

Hello, it's me agane, guy with wierd english language. Senks to google translate.
Anabling usb on RRD-305 module for ADK Configuration tool. It's dirt hack, but if you have not csr-usb-spi adaptor, maybe it's
helps. You doing it on your own risck
Metod consists in replasing original dump with SPI support on dump with USB support.
You need instaled ADK_QCC300x.WIN.1.0.167 (if you are reading this probably you have).
-1. Download dump https://drive.google.com/drive/folders/1HUHScPHVU-FbnREi0fY9V9FPHyFZ0DCI?usp=sharing In folder you find two a banch of files with names starts from usb and spi. Copy files starts from usb to /ADK_QCC300x.WIN.1.0.167\tools\bin
0. Preparation as said in instruction on main page of this project

1. Run windows console (cmd) and change dirrectory to /ADK_QCC300x.WIN.1.0.167\tools\bin
2. Run nvscmd.exe dump original.ptn - it will show a lot of errors and as result after few minuts makes dump of you chip
3. Run nvscmd.exe burn usb.ptn all - it will show a lot of errors and as result write new dump on chip
4. Unsolder ft232 from you module. Solder wires from usb G to GND, D+ to USB-P D- to USB-N V+ to VBUS and test connections.

[LuthfiZXC]

Hello, it's me agane, guy with wierd english language. Senks to google translate.
Anabling usb on RRD-305 module for ADK Configuration tool. It's dirt hack, but if you have not csr-usb-spi adaptor, maybe it's
helps. You doing it on your own risck
Metod consists in replasing original dump with SPI support on dump with USB support.
You need instaled ADK_QCC300x.WIN.1.0.167 (if you are reading this probably you have).
-1. Download dump https://drive.google.com/drive/folders/1HUHScPHVU-FbnREi0fY9V9FPHyFZ0DCI?usp=sharing In folder you find two a banch of files with names starts from usb and spi. Copy files starts from usb to /ADK_QCC300x.WIN.1.0.167\tools\bin
0. Preparation as said in instruction on main page of this project

1. Run windows console (cmd) and change dirrectory to /ADK_QCC300x.WIN.1.0.167\tools\bin
2. Run nvscmd.exe dump original.ptn - it will show a lot of errors and as result after few minuts makes dump of you chip
3. Run nvscmd.exe burn usb.ptn all - it will show a lot of errors and as result write new dump on chip
4. Unsolder ft232 from you module. Solder wires from usb G to GND, D+ to USB-P D- to USB-N V+ to VBUS and test connections.

How to enable USB Programming on QCC3008 ? I tried ur dump file and it didn't work , the log said it has different partition size

[kiterservice]

How to enable USB Programming on QCC3008 ? I tried ur dump file and it didn't work , the log said it has different partition size

Unfortunately, in your case, i don't know any way, exept by using csr-spi programmer. My dump work only with Chinese rrd-305 module based on qcc3005 chip. You module based on qcc3008 chip and has different flash rom with different partition table.
And, speeking honestly, usb connection almost useless. Pstool would not work with usb, for sound settings mutch easier using android app GAIA for qualcomm bluetooth chip.

[RGBlu3-pro]

I have a little problem.

[RGBlu3-pro]

On my second module your method works perfectly. I can do everything in ADK using only USB cable. Thank you so much :)

[djskomy]

Hi, can you re-upload the firmware files? link has expired.

[riccardocagnasso]

Hi, can you re-upload the firmware files? link has expired.

Bump I would really like the firmware too

[djskomy]

I found it here: https://disk.yandex.ru/d/toQ3deXyBR-dMw
It's a part of some audio project: https://cxem.net/sound/amps/amp252.php

[AntonioBanditoz]

Hello everyone I faced the problem of programming the RRD305 module, built a printed circuit board for this module, also purchased a CSR USB SPI module, but it cannot connect to the module in the ADK program, an error ERROR DETECTING CHIP TYPE (READ FAILED ON USB SPI) appears, the electrical wiring diagram of the module was provided to me by the seller. In the first post, you said that you don't need to connect the POWER_EN pin to VBAT, does this also apply to the original programmer?

[SkinnyDonut]

Check the RRD305 documentation, if I remember correctly, one pin requires 5v+ (don't remember at all which pin, check the Pinout descriptions in the documentation) in order to get it ready for programming

…

On Tue, Nov 14, 2023, 21:23 AntonioBanditoz ***@***.***> wrote: Hello everyone I faced the problem of programming the RRD305 module, built a printed circuit board for this module, also purchased a CSR USB SPI module, but it cannot connect to the module in the ADK program, an error ERROR DETECTING CHIP TYPE (READ FAILED ON USB SPI) appears, the electrical wiring diagram of the module was provided to me by the seller. In the first post, you said that you don't need to connect the POWER_EN pin to VBAT, does this also apply to the original programmer? — Reply to this email directly, view it on GitHub <#59 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ADGDPAFQTVUWLB3JTOQXR23YEPAMHAVCNFSM4ZDXQZK2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGEYDIOBTGA2A> . You are receiving this because you commented.Message ID: ***@***.***>

[AntonioBanditoz]

Проверьте документацию RRD305, если я правильно помню, для одного вывода требуется напряжение 5 В + (совсем не помню, для какого вывода, проверьте описания распиновок в документации), чтобы подготовить его к программированию
…
On Tue, Nov 14, 2023, 21:23 AntonioBanditoz @.> wrote: Hello everyone I faced the problem of programming the RRD305 module, built a printed circuit board for this module, also purchased a CSR USB SPI module, but it cannot connect to the module in the ADK program, an error ERROR DETECTING CHIP TYPE (READ FAILED ON USB SPI) appears, the electrical wiring diagram of the module was provided to me by the seller. In the first post, you said that you don't need to connect the POWER_EN pin to VBAT, does this also apply to the original programmer? — Reply to this email directly, view it on GitHub <#59 (comment)>, or unsubscribe https://github.com/notifications/unsubscribe-auth/ADGDPAFQTVUWLB3JTOQXR23YEPAMHAVCNFSM4ZDXQZK2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGEYDIOBTGA2A . You are receiving this because you commented.Message ID: @.>

I checked from 3.3 to 4.2v, below is a link to the documentation, I think the link should open

https://szytf.yuque.com/sz0hxn/vzvo0a/gsfcwx?spm=a2g2w.orderlist.0.0.79ad4aa6dDNXnv

[SkinnyDonut]

https://www.diyaudio.com/community/threads/csr8675-programming-guide-w-software-and-tons-of-csr-info.349336/page-8 Check comment #142 On Tue, Nov 14, 2023, 21:41 AntonioBanditoz ***@***.***> wrote:

…

Проверьте документацию RRD305, если я правильно помню, для одного вывода требуется напряжение 5 В + (совсем не помню, для какого вывода, проверьте описания распиновок в документации), чтобы подготовить его к программированию … <#m_-730341649495741240_> On Tue, Nov 14, 2023, 21:23 AntonioBanditoz *@*.*> wrote: Hello everyone I faced the problem of programming the RRD305 module, built a printed circuit board for this module, also purchased a CSR USB SPI module, but it cannot connect to the module in the ADK program, an error ERROR DETECTING CHIP TYPE (READ FAILED ON USB SPI) appears, the electrical wiring diagram of the module was provided to me by the seller. In the first post, you said that you don't need to connect the POWER_EN pin to VBAT, does this also apply to the original programmer? — Reply to this email directly, view it on GitHub <#59 (comment) <#59 (comment)>>, or unsubscribe https://github.com/notifications/unsubscribe-auth/ADGDPAFQTVUWLB3JTOQXR23YEPAMHAVCNFSM4ZDXQZK2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGEYDIOBTGA2A <https://github.com/notifications/unsubscribe-auth/ADGDPAFQTVUWLB3JTOQXR23YEPAMHAVCNFSM4ZDXQZK2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGEYDIOBTGA2A> . You are receiving this because you commented.Message ID: @.*> I checked from 3.3 to 4.2v, below is a link to the documentation, I think the link should open https://szytf.yuque.com/sz0hxn/vzvo0a/gsfcwx?spm=a2g2w.orderlist.0.0.79ad4aa6dDNXnv — Reply to this email directly, view it on GitHub <#59 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ADGDPAABHFVYDYKW2EPYHCTYEPCPNAVCNFSM4ZDXQZK2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGEYDOOJZGI2Q> . You are receiving this because you commented.Message ID: ***@***.***>

[AntonioBanditoz]

Yes, I have the same connection scheme, the pin VS also tried to connect to 1.8v, the error is exactly the same. I am using ADK 1.0.167

[SkinnyDonut]

Have you tested with older version? I have formated my drive and don't remember the version I used Check if the programmer has correct drivers

…

On Tue, Nov 14, 2023, 22:08 AntonioBanditoz ***@***.***> wrote: Yes, I have the same connection scheme, the pin VS also tried to connect to 1.8v, the error is exactly the same. I am using ADK 1.0.167 — Reply to this email directly, view it on GitHub <#59 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ADGDPAD2JANAQQP55L6DVBTYEPFTVAVCNFSM4ZDXQZK2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGEYTKMZWG4YA> . You are receiving this because you commented.Message ID: ***@***.***>

[AntonioBanditoz]

ok I'll try even older versions. As for the drivers, I did not understand, they are also installed bundled with the programs.

[SkinnyDonut]

I remember that I had some problems with the drivers because I had used zadig Test with older versions and tell me

…

On Wed, Nov 15, 2023, 05:01 AntonioBanditoz ***@***.***> wrote: Ok I'll try even older versions. Did you not understand about the drivers? They are also installed bundled with programs. — Reply to this email directly, view it on GitHub <#59 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ADGDPAG2CPM7NFZPTJJHCYLYEQWCHAVCNFSM4ZDXQZK2U5DIOJSWCZC7NNSXTN2JONZXKZKDN5WW2ZLOOQ5TCOBRGE3TGNBRGI2Q> . You are receiving this because you commented.Message ID: ***@***.***>

[AntonioBanditoz]

you misunderstood me a little, I have an original csr usb spi programmer, I don’t need to replace the driver

[AntonioBanditoz]

Thank you very much! installing the ADK QCC300X V1.0 version helped me.