Comments (6)
Yes, the newest firmware should also support mass storage mode on the DIY-Thermocam V1. But I have to admit I didn't test it in version 2.46. Can you flash 2.45 or a prior version and check if it works there?
from diy-thermocam.
Are there old firmwares archived here? I am having trouble finding any firmware except the current 2.46 version.
from diy-thermocam.
You can find previous firmware releases here: http://diy-thermocam.bplaced.net/Firmware/
from diy-thermocam.
Thanks for the link to the previous firmwares. I did some testing with my version 1 camera and saw slightly different results as the firmware progressed from v.1.25 to v.2.46. The results are below.
From v.1.25 to v.2.39 - Normal operation was observed. Normal operation is defined as the following:
- The USB icon is pressed from the main menu.
- A message pops up that says "Disconnect USB cable to return" is displayed.
- Windows USB disconnect sound is heard followed by the Windows USB connect sound.
- A drive opens in Windows Explorer displaying the contents of the onboard SD card. The contents of the drive can be accessed.
- When the USB cable is unplugged, the camera reboots.
Starting with the v.2.40 firmware to the v.2.44 firmware, a slightly different behavior was observed:
- The USB icon is pressed from the main menu.
- A message pops up that says "Disconnect USB cable to return" is displayed.
- Windows USB disconnect sound is heard.
- Nothing happens
- If the USB cable is disconnected and then reconnected, the Windows USB disconnect sound is heard when the cable is disconnected and then the Windows USB connect sound is heard and then the contents of the SD card is displayed in Windows Explorer. The contents of the drive can be accessed. The message "Disconnect USB cable to return" is still displayed on the camera display.
- When the USB cable is unplugged, the camera reboots.
With the v.2.45 firmware, the normal behavior (v.1.25 to v.2.39) was observed.
With the v.2.46 firmware the following behavior was observed:
- The USB icon is pressed from the main menu.
- A message pops up that says "Disconnect USB cable to return" is displayed.
- Windows USB disconnect sound is heard.
- The camera reboots.
I took a look at the change log for 2.45 to 2.46 and did not see anything that would point to the change in behavior between v.2.45 and v.2.46.
I am not asking for a fix to this since I realize that I have an old device and the newer device does not seem to have problems. I am posting this so that others that may have version 1 camera have a resoure to help solve problems after firmware upgrades.
Thanks again for all your help with this issue. With v2.45 firmware, I have a functional camera again !
from diy-thermocam.
Thanks for those detailed observations!
I had a look what could be the issue with 2.46 and the MSD functionality, but didn't find a quick fix.. Hopefully I will have some more time to investigate this soon, and hope you can use 2.45 without any big issues in the meantime :)
from diy-thermocam.
The v.2.45 firmware works fine for what I am doing and it is a vast improvement from the v.1.25 that I was using!
If you are going to do some troubleshooting on this issue, I am willing to test any potential fixes that you come up with.
from diy-thermocam.
Related Issues (20)
- DIYLepton_Connect()->Index was outside the bounds of the array HOT 1
- Building Instructions v3 Feedback: LED, Lipo Protector, Switch, Heatshrink, Slide Cover HOT 2
- Does the code described here work with DIY Thermocam V2 as well. I suspect the firmware is different. I hope all the other software is the same. Is there a link to the latest version of software for V2? HOT 1
- TP4057 Charging module no longer available HOT 8
- Lepton 3.5 HOT 12
- I can't make the Lepton Breakout Board 2.0 to work HOT 3
- video feed HOT 1
- Arducam 2mp mini plus ov2640 HOT 4
- Camera not working HOT 2
- thermo and image not match correctly HOT 1
- Cam hangs on Boot Screen, Hardware Issue? HOT 13
- DiyThermocam V2 Touch lcd HOT 2
- MTP device Windows 10 HOT 5
- Image transmission via wifi HOT 2
- finished my Themocam, a few remarks for the Enclosure HOT 5
- Having issues getting the firmware on Teensy HOT 4
- Step up converter overheating and powering down on battery HOT 2
- Can't find charging module HOT 3
- Lepton sensor diagnostic failed HOT 5
- Thermocam won't wake up
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from diy-thermocam.