Help with Reading speed (KPH) instead of RPM

[powerbroker2]

Help with Reading speed (KPH) instead of RPM

[PowerBroker2]

Do you want engine speed or vehicle speed? If you want vehicle speed in kph, you can use the kph() function

[jmandradiar]

I want vehicle speed in kph. It would be great if you could modify your same ESP32 bluetooth code, changing the few lines alone for vehicle speed. Would that be possible? (Just to be safe as I doing it with my car, it's my humble request)

…

On Tue, 9 Feb 2021, 5:30 pm PB2, ***@***.***> wrote: Do you want engine speed or vehicle speed? If you want vehicle speed in kph, you can use the kph() function — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#59 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ASZE3EVZSV6CEVGZ5VVKBU3S6EPXVANCNFSM4XKXGX2A> .

[PowerBroker2]

Untested and uncompiled:

#include "BluetoothSerial.h"
#include "ELMduino.h"


BluetoothSerial SerialBT;
#define ELM_PORT   SerialBT
#define DEBUG_PORT Serial


ELM327 myELM327;


uint32_t kph = 0;


void setup()
{
#if LED_BUILTIN
  pinMode(LED_BUILTIN, OUTPUT);
  digitalWrite(LED_BUILTIN, LOW);
#endif

  DEBUG_PORT.begin(115200);
  //SerialBT.setPin("1234");
  ELM_PORT.begin("ArduHUD", true);
  
  if (!ELM_PORT.connect("OBDII"))
  {
    DEBUG_PORT.println("Couldn't connect to OBD scanner - Phase 1");
    while(1);
  }

  if (!myELM327.begin(ELM_PORT))
  {
    Serial.println("Couldn't connect to OBD scanner - Phase 2");
    while (1);
  }

  Serial.println("Connected to ELM327");
}


void loop()
{
  float tempKPH = myELM327.kph();

  if (myELM327.status == ELM_SUCCESS)
  {
    kph = tempKPH;
    Serial.print("KPH: "); Serial.println(kph);
  }
  else
    printError();
}


void printError()
{
  Serial.print("Received: ");
  for (byte i = 0; i < myELM327.recBytes; i++)
    Serial.write(myELM327.payload[i]);
  Serial.println();
  
  if (myELM327.status == ELM_SUCCESS)
    Serial.println(F("\tELM_SUCCESS"));
  else if (myELM327.status == ELM_NO_RESPONSE)
    Serial.println(F("\tERROR: ELM_NO_RESPONSE"));
  else if (myELM327.status == ELM_BUFFER_OVERFLOW)
    Serial.println(F("\tERROR: ELM_BUFFER_OVERFLOW"));
  else if (myELM327.status == ELM_UNABLE_TO_CONNECT)
    Serial.println(F("\tERROR: ELM_UNABLE_TO_CONNECT"));
  else if (myELM327.status == ELM_NO_DATA)
    Serial.println(F("\tERROR: ELM_NO_DATA"));
  else if (myELM327.status == ELM_STOPPED)
    Serial.println(F("\tERROR: ELM_STOPPED"));
  else if (myELM327.status == ELM_TIMEOUT)
    Serial.println(F("\tERROR: ELM_TIMEOUT"));
  else if (myELM327.status == ELM_TIMEOUT)
    Serial.println(F("\tERROR: ELM_GENERAL_ERROR"));

  delay(100);
}

[jmandradiar]

Thanks a lot.

…

On Tue, 9 Feb 2021, 7:33 pm PB2, ***@***.***> wrote: Untested and uncompiled: #include "BluetoothSerial.h" #include "ELMduino.h" BluetoothSerial SerialBT; #define ELM_PORT SerialBT #define DEBUG_PORT Serial ELM327 myELM327; uint32_t kph = 0; void setup() { #if LED_BUILTIN pinMode(LED_BUILTIN, OUTPUT); digitalWrite(LED_BUILTIN, LOW); #endif DEBUG_PORT.begin(115200); //SerialBT.setPin("1234"); ELM_PORT.begin("ArduHUD", true); if (!ELM_PORT.connect("OBDII")) { DEBUG_PORT.println("Couldn't connect to OBD scanner - Phase 1"); while(1); } if (!myELM327.begin(ELM_PORT)) { Serial.println("Couldn't connect to OBD scanner - Phase 2"); while (1); } Serial.println("Connected to ELM327"); } void loop() { float tempKPH = myELM327.kph(); if (myELM327.status == ELM_SUCCESS) { kph = tempKPH; Serial.print("RPM: "); Serial.println(kph); } else printError(); } void printError() { Serial.print("Received: "); for (byte i = 0; i < myELM327.recBytes; i++) Serial.write(myELM327.payload[i]); Serial.println(); if (myELM327.status == ELM_SUCCESS) Serial.println(F("\tELM_SUCCESS")); else if (myELM327.status == ELM_NO_RESPONSE) Serial.println(F("\tERROR: ELM_NO_RESPONSE")); else if (myELM327.status == ELM_BUFFER_OVERFLOW) Serial.println(F("\tERROR: ELM_BUFFER_OVERFLOW")); else if (myELM327.status == ELM_UNABLE_TO_CONNECT) Serial.println(F("\tERROR: ELM_UNABLE_TO_CONNECT")); else if (myELM327.status == ELM_NO_DATA) Serial.println(F("\tERROR: ELM_NO_DATA")); else if (myELM327.status == ELM_STOPPED) Serial.println(F("\tERROR: ELM_STOPPED")); else if (myELM327.status == ELM_TIMEOUT) Serial.println(F("\tERROR: ELM_TIMEOUT")); else if (myELM327.status == ELM_TIMEOUT) Serial.println(F("\tERROR: ELM_GENERAL_ERROR")); delay(100); } — You are receiving this because you authored the thread. Reply to this email directly, view it on GitHub <#59 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/ASZE3EXPECPZXHZ3EYYV44LS6E6EBANCNFSM4XKXGX2A> .

[PowerBroker2]

No prob!