timing of time travel

[reala10001986]

timing of time travel

[realA10001986]

I am not sure I understand: You need to know the time it takes from

• first blink to all off
• all off to disruption
• and so on?

[realA10001986]

Assuming you meant what I think you meant, there are several phases:

• phase 1 starts with IO14 going HIGH, and takes 5000ms
• phase 2 is 2800ms while the displays blink as a whole,
• phase 3 is 1600ms while the displays are all off,
• phase 4 is 1000ms while the display show random stuff part 1,
• phase 5 is 1200ms while the display show random stuff part 2.

At the end of phase 5, IO14 goes LOW. The displays go on 1500ms after the end of phase 5.

(I hope this is all correct, it's from the top of my head)

[Fabiobttf]

Yes this is what I need, I think just add the time or is there some pause between different phase ? example: * phase 1 starts with IO14 going HIGH, and takes.................... 5000ms * phase 2 is 2800ms while the displays blink as a whole,......... (5000+2800) * phase 3 is 1600ms while the displays are all off,......................(7800+1600) * phase 4 is 1000ms while the display show random stuff part 1,(9400+1000) * phase 5 is 1200ms while the display show random stuff part 2.(10400+1200) thanks a lot bye

…

Assuming you meant what I think you meant, there are several phases: * phase 1 starts with IO14 going HIGH, and takes 5000ms * phase 2 is 2800ms while the displays blink as a whole, * phase 3 is 1600ms while the displays are all off, * phase 4 is 1000ms while the display show random stuff part 1, * phase 5 is 1200ms while the display show random stuff part 2. At the end of phase 5, IO14 goes LOW. The displays go on 1500ms after the end of phase 5. (I hope this is all correct, it's from the top of my head) — Reply to this email directly, view it on GitHub <#4 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/A5FYV6VSLIPX3ELIJF34BFTXEFX5DANCNFSM6AAAAAAXTOSHT4>. You are receiving this because you authored the thread. <https://github.com/notifications/beacon/A5FYV6WJOUS2QZDPK3LTZZTXEFX5DA5CNFSM6AAAAAAXTOSHT6WGG33NNVSW45C7OR4XAZNMJFZXG5LFINXW23LFNZ2KUY3PNVWWK3TUL5UWJTS3KKE44.gif>Message ID: ***@***.***>

[realA10001986]

No, there is no pause inbetween.

[realA10001986]

But don't expect the timing to always be exact, depending on the current work load (GPS, WiFi, etc) it might vary slightly.

[Fabiobttf]

ok, I'll try with this time, I have no wifi or GPS connection only have temperature sensor, speedometer and light sensor, but I think this sensor not enable during time travel sequence (except speedometer);

…

Il 03/05/2023 13:48 A10001986 ***@***.***> ha scritto: But don't expect the timing to always be exact, depending on the current work load (GPS, WiFi, etc) it might vary slightly. — Reply to this email directly, view it on GitHub <#4 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/A5FYV6SCQWJJFJNSNG25MY3XEJA2BANCNFSM6AAAAAAXTOSHT4>. You are receiving this because you authored the thread. <https://github.com/notifications/beacon/A5FYV6VES2VQDFY5ZOHUYXLXEJA2BA5CNFSM6AAAAAAXTOSHT6WGG33NNVSW45C7OR4XAZNMJFZXG5LFINXW23LFNZ2KUY3PNVWWK3TUL5UWJTS3LYBQ4.gif>Message ID: ***@***.***>

[alalal80]

Good evening,
I have several ideas to increase this fabulous machine, for the alarm,
why not add an output that will control a servo motor to ring the ticks of the clock instead of the sound of the clock.
still great work.
have the possibility of having a countdown for a given date and time.
Well, thank you again for your work.