Weird Home Assistant Controls behaviours

[rstrouse]

Weird Home Assistant Controls behaviours

[afmaniacc]

Hi i have the same Problem, do you found a solution for that?
but iam on Firmware 1.5.1

[rstrouse]

Can I get both of you to try something for me. With the shades completely stopped. Press the my button on the remote. If the shade moves I may know what it going on. Are these shades set up as roller shades, draperies, or blinds? If they are blinds what type has been selected for the motor type?

On that note, is it difficult to add another entity to show that there is a new firmware update available?

I'll have a look to see if I can figure something out here.

[isngofoz]

To be honest, I usually only used the MY button as a 'Stop' button on the remote.

Anyways, I tried according to what you said and interestingly enough, I believe the shutter moved to that position I described above, almost closed but not closed. Mine are metal roller shutters so I choose Roller Shade as the type.

[rstrouse]

Ok so press the my button and let the shutter move to that position. After it is done moving hold down the my button on the remote until it jogs.

[011V32]

I also have the behavior from time to time (also directly in the ESPSomfyRTS web interface). But I was not sure if it was related to the fact that at the end (0% or 100%) the My position was also controlled...
(This then only occurs when the time is greater than the blinds shutdown time.)

[isngofoz]

Ok so press the my button and let the shutter move to that position. After it is done moving hold down the my button on the remote until it jogs.

Okay, done. How does this solve the issue?

[rstrouse]

This removes the my position that ESPSomfy-RTS is not currently aware of. Next you need to update your firmware and application to 1.5.3 which does not issue a stop (my) command when the motor is expected to go to its limits.

[rstrouse]

If you want to set a my position, set it first with ESPSomfy RTS by holding down the my button on the ESPSomfy RTS app until the Set My Position screen opens. Move the slider to the new my position then press Set My Position. The motor will move to this position and stop then it will jog indicating the my position is set.

From here on out if the motor is idle and you press the my button, it will move to the set position.

[isngofoz]

If you want to set a my position, set it first with ESPSomfy RTS by holding down the my button on the ESPSomfy RTS app until the Set My Position screen opens. Move the slider to the new my position then press Set My Position. The motor will move to this position and stop then it will jog indicating the my position is set.

For some reason, after clicking the Set My Position button, the motor moves to the position that I usually like the shutter to stop at but it does not jog. The My Position does get updated though but when I click My button the on-screen shutter simulates a move but the actual shutter stays put. This is running v1.5.3 .

I also tried it today on v1.5.2 and it also did not jog as well when setting the My position. It seems to me that there is an issue setting the My position using ESPSomfy. I just tried setting the My position with the remote and it worked.

[rstrouse]

Thanks, I will have another look at that code. It may not be holding the signal long enough. It will be fixed in the next release.

[isngofoz]

Thanks for responding back so quickly.

I hope you don't mind me thinking out loud. I have learnt from above that the My Button should only be pressed (held) when the shutter is at idle to set the My Position. However with the ESPSomfy, the Set My Position is done in one click. Is it possible that the code is sending the My Position too early while the shutter is still moving?

Either way, thanks for checking. I will monitor the post and test the update when it is available.

[rstrouse]

Nope it appears that it needs to repeat the command much longer than it is once it makes it to the my position destination. Originally I assumed it only needed to hold for 15 repeats but it appears it needs to do it for 25.

[rstrouse]

v1.5.4 fixes your My button woes.

[isngofoz]

Hi there, thanks. Yes, it definitely did solve the My settings.

Not a big deal but I did noticed that 55% in Home Assistant works out to be 45% when I was setting the My position. But I guess My Position isn't exactly used HA anyways so once it is setup, it doesn't really matter.

[rstrouse]

That is correct. The Home Assistant cover is displayed in percentage of open and cannot be changed without completely rewriting the cover domain component. I cannot find words to describe how ridiculous that is but at some point I will recode the Home Assistant interface to use my own cover domain.

This means the 55% closed it 45% open in Home Assistant. Hard to complain when it is open source and I need to rework it so it works logically. I love Home Assistant but that really does put the ass in the assistant. Is my type A showing?

[isngofoz]

As you mentioned, it is open source and free, so probably all it needs is just a simple note that when setting My position based on a desired position in HA, to get the same position, you need to use 100% - the HA % and that's what you want to set.

Either way, as per my first post above, thanks for your awesome solution. It has allowed me to automate my shutters to open up after sunrise when someone is at home and motion is detected, but if I jump on my bed during the day (bed has FSR sensors), the shutters will automatically closed down.

Happy for you to close this issue.

[rstrouse]

I now dub you @isngofoz knight of crazy home automationville. Not throwing stones I am a long time resident.