tschaban/afe-firmware

Firmware for ESP based devices for home automation

AFE-Firmware

Firmware for ESP based devices for home automation

AFE Firmware is software written for the ESP8266 / 8285 / 32 microcontrollers, which is more and more often found in commercial products. ESP is relatively cheap and enables to create your own modules almost like building blocks. The module with AFE Firmware is mainly used in intelligent homes. The modules can control lighting, gates, garden irrigation system, as well as read various parameters: temperature, humidity, atmospheric pressure, suspended pollen and many more.

The module with AFE Firmware installed can be wirelessly controlled by automation systems such as openHAB, Domoticz, Domotiga, HomeAssistant and probably by many other automation systems.

AFE Firmware docs

More information on the YouTube channel

English version | Polska wersja

afe-firmware's Issues

Add possibility to erase EEPROM while upgrading version of the firmware

EEPROM conversion from float cuts the number

Saving -12.345 to EEPROM
while reading it read gets -12.34 - somehow rounded

Library for MQTT connections

While upgrading from different type of firmware it should clear EEPROM

expect WiFi config if it was possible

Build WebServer for handling HTTP request

Add Amazon Echo native support

change state after losing connection

functionality submitted to all AFE Firmware
tschaban/SONOFF-BASIC-firmware#25

MQTT doesn't work

Add functionality to capture error and display it at config panel

HTTP API

Not publishing relay MQTT state while changed by MQTT Message

add possibility to configure connection parameters related to establishing connection and re-connection to MQTT Borker

While pressing mulitifunction switch for 5 sec it should flash the LED

usability : to indicate that switch was pressed for 5sec and can be released to launch config panel

Add LED indication for establishing connection with MQTT Broker

Enable Access Point configuration access

Build a class with all potential configuration options

Library for DS18b20 sensor

Add option for setting fixed IP,Gate and DNS

Add possibility to leave the loop of not possible WiFi connections establishment

Configuration Panel over Access Point sometimes does not work properly

• not refresh pages completely
• not pen pages after data save

while page is refreshed it works

HTTP Communicator is slow in Sonoff AFE Firmware.

• after 20 minutes HTTP request to state change does not work - it's needed to request 3 times from eg Domoticz to change the state.
• if button in Sonoff is pressed it seems to come back to stable mode for couple of minutes
• Connection to WiFI is slow
• all findings from 0.8.8 Sonoff AFE version

problem description here in PL
http://smart-house.adrian.czabanowski.com/forum/zglaszanie-problemow/zapytanie/paged/3/#post-763

Library for external switch manipulation

Library for LED manipulation

Remove hardcoded links to the change log

Build library for dust sensor support

Add configuration upgrade post firmware upgrade

Build configuration panel over HTTP

add relay toggle command for MQTT and HTTP API

Library for relay manipulation

Remove code for debugging

HTTP request should handle "save" parameter

Build functionality for Wifi connection establishment in pre-defined cycles

Add EN localization

LED class should be initialized by ID instead of GPIO

Set same style as for Relay and Switch

Enable configuration over the network

MQTT Interface for information exchange / generic

BUG: setting relay to oposite value after power restore doesn't work

http://smart-house.adrian.czabanowski.com/forum/firmware-do-przelacznika-sonoff/afe-firmware-1-0-0-rc1-wczesny-dostep/#post-1365

Build library for DHT11, DHT21, DHT22 sensor

Add external switch

Firmware should not crash if ds18b20 is not connected.

Automatic upgrade of the firmware: over the internet

add possibility to configure connection parameters related to establishing connection and re-connection to WiFi

Build library for PIR support

Set default value of a relay as early as possible while device is being initialized

currently is after WiFi initialization

http://smart-house.adrian.czabanowski.com/forum/firmware-do-przelacznika-sonoff/afe-firmware-1-0-0-rc1-wczesny-dostep/#post-1342

Add possibility to connect more than one ds18b20 sensors

Hide configurations sections for not connected hardware

Remove code of debugging or add debug on/off option

Build EEPROM library

Add new option of default relay state after power restore

Opposite to last remembered

Build over the air upgrade functionality