Network tab is changing native resolution

[z-bolt]

Network tab is changing native resolution

[rhukster]

Try restarting the service, fixed it for me:

sudo systemctl restart octoscreen.service

[Protoncek]

It does fix it, sure, but only temporary, until i touch network tab again, so long term it's not really a solution.

[Protoncek]

Hi!
I just wanted to say that i have yet another "strange" resolution shift: it happens right after i select file i click "print".

[Protoncek]

Hello, alexkv!
Today i play a bit with this bug. I didn't solve anything, but i discovered interesting feature:
I took RPi4, i installed octoprint and octoscreen, i DIDN'T connect my printer, nor i did any setup in web interface, i just connected original 7 inch LCD and tested octoscreen.
Since without printer connected octoscreen crashes every 10-15 seconds (a known bug, as it seems), i found out that screen shift no longer appears after first crash and reload of octoscreen. However, it seems that this is not the case if i manually restart octoscreen service...

Other than that sadly i didn't come to a solution. If i set resolution to bigger (so that in fact i have smaller picture than whole LCD) i see that when touching "newtork" then resolution actually increases in X direction, creating black empty space on left side.
i tried changing resolution in /boot/config, tried in octoscreen config (even tried without config set in octoscreen config), nothing helps.
It's strange, i know... but i hope that information helps anything regarding this issue...

[AstroClimber]

Other than that sadly i didn't come to a solution. If i set resolution to bigger (so that in fact i have smaller picture than whole LCD) i see that when touching "newtork" then resolution actually increases in X direction, creating black empty space on left side.
i tried changing resolution in /boot/config, tried in octoscreen config (even tried without config set in octoscreen config), nothing helps.

Hi Protoncek,
Did you also set the two parameters framebuffer_width and framebuffer_height in /boot/config.txt when you are setting the resolution? For me, before I set those two framebuffers, the resolution changed when I click the network tab. But now, it has stopped changing.

[Protoncek]

Yes, i did try that, i entered real resolution (800x480) and also 800x533, but same still happens. i disabled overscan, too, but same happens.
Interesting is that at print menu shift is sometimes less than the one i posted above...

[rhukster]

Seems to me the problem is just related to the WIFI network names overflowing the available area and pushing out the width of the display. Just need to hide the overflow and add some ellipsis, or reformat the output so there's more room for WIFI network names.

[DamnSkippy1999]

Hello, new to Github so my apologies for any errors. I have been using the Octoscreen for several weeks and have noticed the shift in resolution as well. Usually occurs when I queue up a print. I have not checked my framebuffer (in the middle of a print) settings yet but will verify shortly. I have not been able to tie it to a common variable. I originally thought it was due to longer prints but noticed it with shorter prints recently. I will observe the names of the prints and see if it happens when the length is rather long. I only notice the shift when printing but will test the Network screen to see if it happens on my end.

[Protoncek]

Seems to me the problem is just related to the WIFI network names overflowing the available area and pushing out the width of the display. Just need to hide the overflow and add some ellipsis, or reformat the output so there's more room for WIFI network names.

Hm...i doubt it's wifi name in network tab... my Wifi names are short. It could be the problem on print tab, though. My print file names ARE quite long, so i'll check out with shorter tomorrow.

[Protoncek]

As promised, today i tried to print gcode with very short name and ...voila! Screen shift is gone! So, it IS something with too long filenames.
On network tab i assume that first time, when there's empty space system "reserves" too much of blank space...

[SupremeCookie11]

Hi,

Any updates on when this might be fixed?

still cant get out of network screen due to scaling

[niccoreyes]

Currently having the same problem. I tried Protoncek's solution with short gcode name, and it doesn't appear again. It appears to be reproducible with long file names. Will continue to observe this behavior for my future prints. I am currently using a tft 3.5" display with 480x320 with waveshare drivers.

[sd-brady]

Hi!
I just wanted to say that i have yet another "strange" resolution shift: it happens right after i select file i click "print".

I'm also having this same problem.

[rwaspe]

Here is a fix: #126

[thebeline]

@Psyclonian - Has this issue been resolved for you?

[JeffB42]

@Psyclonian 2.7.0 has been released, and 2.7 & 2.6 have fixed a lot of bugs. Please update to 2.7.0 and let me know if this is still an issue.

[JeffB42]

Closed due to lack of response.