19chang19/autokit-cpc200-t2c-research

Research project for CPC200-T2C

Autokit CPC200 T2C research

Notes

• WiFi only model
• PCB Rev: 20221019
• Hardware version: CA-BT-PanNet-A1
• Initial firmware version: 23071316.4.9

Chips

• Main SoC: Allwinner V833 (sun8iw19, Cortex-A7)
• RAM: Samsung K4B1G1646I-BCMA (DDR3 1Gb)
• Flash: Winbond W25Q128JV (16 MB, 3.3v)
• WiFi/Bluetooth: Realtek RTL8821CS
• LTE-Modem: Neoway N58-EA

Flash Pinout

   -------------
1 -| ~CS   VCC |- 8
2 -|  DO  ~RST |- 7
3 -| ~WP   CLK |- 6
4 -| GND    DI |- 5
   -------------

Flash Structure

The stage0 needs to be figured out.

Start	Size	Partition	Description
0x060000	0x040000	env	U-Boot env (reduntant)
0x0A0000	0x220000	boot	uImage
0x2C0000	0x220000	recovery	uImage
0x4E0000	0x300000	rootfs	Root SquashFS
0x7E0000	0x640000	customer	Customer SquashFS
0xe20000	0x010000	private
0xe30000	0x4a0000	UDISK	User Disk JFFS2

From DTS:

partitions {
    device_type = "partitions";

    env {
        device_type = "env";
        offset = <0x20>;
        size = <0x200>;
    };

    boot {
        device_type = "boot";
        offset = <0x220>;
        size = <0x1100>;
    };

    recovery {
        device_type = "recovery";
        offset = <0x1320>;
        size = <0x1100>;
    };

    rootfs {
        device_type = "rootfs";
        offset = <0x2420>;
        size = <0x1800>;
    };

    customer {
        device_type = "customer";
        offset = <0x3c20>;
        size = <0x3200>;
    };

    private {
        device_type = "private";
        offset = <0x6e20>;
        size = <0x80>;
    };

    UDISK {
        device_type = "UDISK";
        offset = <0x6ea0>;
        size = <0x00>;
    };
};

• Block size: 512
• Base: 0x5c000 (This is figured out by cross-referencing binwalk results and DTS. I'm not sure, is this static between FWs)

First Boot

U-Boot(09/02/2022-18:42:57)


U-Boot 2018.05 (Sep 02 2022 - 18:42:57 +0800) Allwinner Technology

[00.214]DRAM:  128 MiB
[00.217]Relocation Offset is: fdf90000
[00.227]secure enable bit: 0
[00.230]CPU=1008 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz  MBus=198Mhz
[00.236]gic: sec monitor mode
[00.239]flash init start
[00.241]workmode = 0,storage type = 3
SF: Detected w25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
[00.256]sunxi flash init ok
[00.260]Loading Environment from SUNXI_FLASH... OK
[00.314]update dts
boot_partition is boot
root_partition is rootfs
set root to /dev/mtdblock4
[00.325]update part info
[00.327]update bootcmd
Hit any key to stop autoboot:  0 
## Booting kernel from Legacy Image at 4007f800 ...
   Image Name:   ARM OpenWrt Linux-4.9.118
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2224312 Bytes = 2.1 MiB
   Load Address: 40008000
   Entry Point:  40008004
[00.883]Starting kernel ...

/etc/init.d/rcS: /etc/init.d/rc.final: line 14: can't create /sys/class/hwmon/hwmon0/port_qos: nonexistent directory
/etc/init.d/rcS: /etc/init.d/rc.final: line 15: can't create /sys/class/hwmon/hwmon0/port_qos: nonexistent directory
data partitions have 844

root@None:/# ly_boot
BOOT_MODE=normal
DEBUG_MODE=no
sh: 1: unknown operand
LY_LINK_TYPE=cp
WORKDIR=/mnt/customer/app
setusbconfig
mkdir: can't create directory '/sys/kernel/config/usb_gadget/g1/functions/ffs.adb': No such file or directory
mkdir: can't create directory '/sys/kernel/config/usb_gadget/g1/functions/mtp.gs0': No such file or directory
mkdir: can't create directory '/sys/kernel/config/usb_gadget/g1/functions/mass_storage.usb0': No such file or directory
/bin/setusbconfig: line 111: can't create /sys/kernel/config/usb_gadget/g1/functions/mass_storage.usb0/lun.0/inquiry_string: nonexistent directory
WIFI_MODULE=8821cs
wait udisk trial=0
run gocsdk BT_NAME=AutoKit_76EA
## Error: "swu_mode" not defined
current ly_project=ly1552 buil date:Oct 27 2022
update_ok_wait_time=5
 run lylinkui
kill /sbin/update
start /mnt/customer/app/update
mDNSResponder: mDNSResponder (Engineering Build) (Jun  9 2022 17:12:58) starting
mDNSResponder: Unable to parse DNS server list. Unicast DNS-SD unavailable
mDNSResponder: mDNSPlatformSourceAddrForDest: connect 1.1.1.1 failed errno 101 (Network unreachable)
## Error: "swu_mode" not defined
current ly_project=ly1552 buil date:Oct 27 2022
update_ok_wait_time=5
SetKeyChainPath 93:carlife save keychain path:/mnt/UDISK/lylink ,name:carplay.key
mDNSResponder: Unable to parse DNS server list. Unicast DNS-SD unavailable
mDNSResponder: mDNSPlatformSourceAddrForDest: connect 1.1.1.1 failed errno 101 (Network unreachable)

Serial Console

• TTL 3.3v
• Baudrate 115200
• Input is disabled by default
  • uboot's bootdelay=0
  • /sys/module/sunxi_uart/parameters/debug_mode = 0

To enable input:

1. Patch bootdelay=5 in uboot's env and reflash the firmware
2. In uboot's console:
   1. env set ly_boot_mode adb
   2. env save
   3. boot
3. Create /mnt/UDISK/app/httpd and chmod +x /mnt/UDISK/app/httpd:

#!/bin/sh

echo "[+] httpd hijack"
echo "[+] enable debug uart"

echo 1 > /sys/module/sunxi_uart/parameters/debug_mode

exec /usr/sbin/httpd "$@"`

Restore ly_boot_mode:

1. env set ly_boot_mode normal
2. env save

Firmware Updates

curl 'https://cpbox.oss-cn-shenzhen.aliyuncs.com/1552/version.json?rand=0.05004765868326899' \
  -H 'sec-ch-ua: "Microsoft Edge";v="117", "Not;A=Brand";v="8", "Chromium";v="117"' \
  -H 'Referer: https://tespush.com/' \
  -H 'sec-ch-ua-mobile: ?0' \
  -H 'User-Agent: Mozilla/5.0 (Windows NT 10.0; Win64; x64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/117.0.0.0 Safari/537.36 Edg/117.0.2045.47' \
  -H 'sec-ch-ua-platform: "Windows"' \
  --compressed

{"appver": "23061210.1552.1", "tsl": "23061210.4.9", "url": "https://cpbox.oss-cn-shenzhen.aliyuncs.com/1552/update_230612.img", "msg": "[2023-06-12] V4.9 </br>1.Add mode menu for the encoder.</br>2.Use pictures encoding by default.</br>1.增加编码器的模式菜单</br>2.默认使用图片编码", "test": [
{"appver": "23123012.1552.1", "tsl": "23123012.4.9", "sn": "xxx", "url": "https://cpbox.oss-cn-shenzhen.aliyuncs.com/1552/test.img", "msg": " This is test version."}
]}

Device Tree

Decompiling the Device Tree (DTB)

dtc -I dtb -O dts <your DTB> -o <dts filename>

U-Boot env

• The flash has two uboot env blobs: (0x060000, 0x080000)
• Size: 0x20000 (/etc/fw_env.config)

It has some weirdness since looks like the header has a redundant byte. However, it's 0 for both blobs, and the CRC32 value includes the redundant byte. So, this acts like a single uboot env (the header contains only the crc32 value).

$ xxd uboot-env.bin |head
00000000: 894a 8162 0065 6172 6c79 7072 696e 746b  .J.b.earlyprintk
00000010: 3d73 756e 7869 2d75 6172 742c 3078 3035  =sunxi-uart,0x05
00000020: 3030 3030 3030 0069 6e69 7463 616c 6c5f  000000.initcall_
00000030: 6465 6275 673d 3000 636f 6e73 6f6c 653d  debug=0.console=

Misc

root@None:/# uname -a
Linux None 4.9.118 #511 PREEMPT Tue Apr 25 11:47:33 UTC 2023 armv7l GNU/Linux
root@None:/# cat /proc/cpuinfo
processor       : 0
model name      : ARMv7 Processor rev 5 (v7l)
BogoMIPS        : 48.00
Features        : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae
CPU implementer : 0x41
CPU architecture: 7
CPU variant     : 0x0
CPU part        : 0xc07
CPU revision    : 5

Hardware        : sun8iw19
Revision        : 0000
Serial          : 0000000000000000

root@None:/# cat /proc/cmdline
earlyprintk=sunxi-uart,0x05000000 initcall_debug=0 console=ttyS0,115200 loglevel=3 root=/dev/mtdblock4 rootwait init=/pseudo_init rdinit=/rdinit partitions=env@mtdblock1:boot@mtdblock2:recovery@mtdblock3:rootfs@mtdblock4:customer@mtdblock5:private@mtdblock6:UDISK@mtdblock7 cma=4M coherent_pool=16K ion_carveout_list= led_mode=2 androidboot.hardware=sun8iw19p1 boot_type=3 androidboot.boot_type=3 gpt=1 uboot_message=(09/02/2022-18:42:57)
root@None:/# cat /proc/mtd
dev:    size   erasesize  name
mtd0: 00060000 00001000 "uboot"
mtd1: 00040000 00001000 "env"
mtd2: 00220000 00001000 "boot"
mtd3: 00220000 00001000 "recovery"
mtd4: 00300000 00001000 "rootfs"
mtd5: 00640000 00001000 "customer"
mtd6: 00010000 00001000 "private"
mtd7: 001d0000 00001000 "UDISK"

root@None:/# df -Th
Filesystem           Type            Size      Used Available Use% Mounted on
/dev/root            squashfs        3.0M      3.0M         0 100% /
devtmpfs             devtmpfs       58.5M         0     58.5M   0% /dev
tmpfs                tmpfs          60.6M      4.0K     60.6M   0% /tmp
/dev/by-name/customer
                     squashfs        6.0M      6.0M         0 100% /mnt/customer
/dev/by-name/UDISK   jffs2           1.8M   1020.0K    836.0K  55% /mnt/UDISK

root@None:/# ps w
  PID USER       VSZ STAT COMMAND
    1 root      1032 S    /sbin/init
    2 root         0 SW   [kthreadd]
    3 root         0 SW   [ksoftirqd/0]
    4 root         0 SW   [kworker/0:0]
    5 root         0 SW<  [kworker/0:0H]
    6 root         0 SW   [kworker/u2:0]
    7 root         0 SW   [rcu_preempt]
    8 root         0 SW   [rcu_sched]
    9 root         0 SW   [rcu_bh]
   10 root         0 SW<  [lru-add-drain]
   11 root         0 SW   [kdevtmpfs]
   12 root         0 SW   [kworker/u2:1]
  220 root         0 SW   [oom_reaper]
  221 root         0 SW<  [writeback]
  223 root         0 SW   [kcompactd0]
  224 root         0 SW<  [crypto]
  225 root         0 SW<  [bioset]
  227 root         0 SW<  [kblockd]
  301 root         0 SW   [sys_user]
  308 root         0 SW   [kworker/0:1]
  309 root         0 SW<  [cfg80211]
  312 root         0 DW   [ly_rgb_led_th]
  315 root         0 DW   [ly_update_scan]
  318 root         0 SW<  [watchdogd]
  333 root         0 SW<  [spi0]
  343 root         0 SW   [kswapd0]
  441 root         0 SW<  [bioset]
  445 root         0 SW<  [bioset]
  450 root         0 SW<  [bioset]
  455 root         0 SW<  [bioset]
  460 root         0 SW<  [bioset]
  465 root         0 SW<  [bioset]
  471 root         0 SW<  [bioset]
  476 root         0 SW<  [bioset]
  512 root         0 SW   [irq/305-sunxi-m]
  539 root         0 SW<  [ipv6_addrconf]
  549 root         0 SW<  [bat_events]
  558 root         0 SW<  [kworker/0:1H]
  559 root         0 SW   [kworker/0:2]
  560 root         0 SW   [kworker/u2:2]
  590 root         0 SWN  [jffs2_gcd_mtd7]
  599 root      1036 S    -/bin/sh
  655 root         0 SW   [kworker/0:3]
  669 root         0 SW   [kworker/0:4]
  679 root      7500 S<   /mnt/customer/app/gocsdk -T/dev/ttyS3 -NAutoKit_76EA
  716 root         0 SW   [ksdioirqd/mmc0]
  729 root         0 SW   [RTW_XMIT_THREAD]
  730 root         0 SW   [RTW_RECV_THREAD]
  731 root         0 SW   [RTW_CMD_THREAD]
  732 root         0 SW   [RTWHALXT]
  742 root      7692 S    /tmp/lylink/tesla -s
  774 root      1044 S    udhcpd /mnt/customer/app/udhcpd.conf
  775 root      7548 S    /mnt/customer/app/lylinkapp
  784 root       680 S    /tmp/update
  804 root      1032 S    /usr/sbin/httpd -p 192.168.3.1:80 -c /tmp/ota/httpd.conf
  808 root      8276 S    /mnt/customer/app/lylinkapp
  814 root      1248 S    /mnt/customer/app/mdnsd
  816 root      9236 S    /tmp/lylink/tesla -s
  854 root      8220 S<   /mnt/customer/app/gocsdk -T/dev/ttyS3 -NAutoKit_76EA
  880 root      1556 S    hostapd -B /tmp/hostapd.conf
  881 root         0 SW   [kworker/u2:3]
  927 root      1032 R    ps w

root@None:/# netstat -antup
Active Internet connections (servers and established)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       PID/Program name
tcp        0      0 101.200.208.6:80        0.0.0.0:*               LISTEN      816/tesla
tcp        0      0 192.168.3.1:80          0.0.0.0:*               LISTEN      804/httpd
tcp        0      0 0.0.0.0:34517           0.0.0.0:*               LISTEN      808/lylinkapp
tcp        0      0 0.0.0.0:7000            0.0.0.0:*               LISTEN      808/lylinkapp
tcp        0      0 0.0.0.0:443             0.0.0.0:*               LISTEN      816/tesla
tcp        0      0 :::7000                 :::*                    LISTEN      808/lylinkapp
udp        0      0 0.0.0.0:53              0.0.0.0:*                           816/tesla
udp        0      0 0.0.0.0:44859           0.0.0.0:*                           814/mdnsd
udp        0      0 0.0.0.0:67              0.0.0.0:*                           774/udhcpd
udp        0      0 127.0.0.1:33913         127.0.0.1:33913         ESTABLISHED 808/lylinkapp
udp        0      0 0.0.0.0:5353            0.0.0.0:*                           814/mdnsd
udp        0      0 127.0.0.1:49649         127.0.0.1:49649         ESTABLISHED 808/lylinkapp

root@None:/proc# cat /proc/sys/kernel/randomize_va_space
2

root@None:/proc# dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.9.118 (os@machine) (gcc version 6.4.1 (OpenWrt/Linaro GCC 6.4-2017.11 2017-11) ) #511 PREEMPT Tue Apr 25 11:47:33 UTC 2023
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=50c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt:Machine model: sun8iw19
[    0.000000] ion_mem_reserve: err format for ion reserve list!
[    0.000000] cma: Reserved 4 MiB at 0x47c00000
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 32768
[    0.000000] free_area_init_node: node 0, pgdat c04434d4, node_mem_map c7af7000
[    0.000000]   Normal zone: 256 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 32768 pages, LIFO batch:7
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] CPU: All CPU(s) started in SVC mode.
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
[    0.000000] Kernel command line: earlyprintk=sunxi-uart,0x05000000 initcall_debug=0 console=ttyS0,115200 loglevel=3 root=/dev/mtdblock4 rootwait init=/pseudo_init rdinit=/rdinit partitions=env@mtdblock1:boot@mtdblock2:recovery@mtdblock3:rootfs@mtdblock4:customer@mtdblock5:private@mtdblock6:UDISK@mtdblock7 cma=4M coherent_pool=16K ion_carveout_list= led_mode=2 androidboot.hardware=sun8iw19p1 boot_type=3 androidboot.boot_type=3 gpt=1 uboot_message=(09/02/2022-18:42:57)
[    0.000000] PID hash table entries: 512 (order: -1, 2048 bytes)
[    0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Memory: 119864K/131072K available (2945K kernel code, 248K rwdata, 836K rodata, 148K init, 1186K bss, 7112K reserved, 4096K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xc8800000 - 0xff800000   ( 880 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
[    0.000000]     modules : 0xbf800000 - 0xc0000000   (   8 MB)
[    0.000000]       .text : 0xc0008000 - 0xc02e8988   (2947 kB)
[    0.000000]       .init : 0xc03e1000 - 0xc0406000   ( 148 kB)
[    0.000000]       .data : 0xc0406000 - 0xc04441f0   ( 249 kB)
[    0.000000]        .bss : 0xc04441f0 - 0xc056cbec   (1187 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Build-time adjustment of leaf fanout to 32.
[    0.000000] NR_IRQS:16 nr_irqs:16 16
[    0.000000] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000013] Switching to timer-based delay loop, resolution 41ns
[    0.000058] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000067] pid_max: default: 32768 minimum: 301
[    0.000189] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000194] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000620] CPU: Testing write buffer coherency: ok
[    0.000816] Setting up static identity map for 0x400081c0 - 0x4000820c
[    0.001854] devtmpfs: initialized
[    0.023013] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.023258] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.023272] futex hash table entries: 256 (order: -1, 3072 bytes)
[    0.023520] atomic64_test: passed
[    0.023525] pinctrl core: initialized pinctrl subsystem
[    0.024281] NET: Registered protocol family 16
[    0.025075] DMA: preallocated 16 KiB pool for atomic coherent allocations
[    0.027062] sunxi iommu: irq = 23
[    0.030787] sun8iw19p1-r-pinctrl r_pio: initialized sunXi PIO driver
[    0.041996] sun8iw19p1-pinctrl pio: initialized sunXi PIO driver
[    0.043645] iommu: Adding device 1c0e000.ve to group 0
[    0.044359] iommu: Adding device 2300000.eise to group 0
[    0.050194] iommu: Adding device 1480000.g2d to group 0
[    0.050587] iommu: Adding device 2400000.nna to group 0
[    0.077095] usbcore: registered new interface driver usbfs
[    0.077161] usbcore: registered new interface driver hub
[    0.077718] usbcore: registered new device driver usb
[    0.077792] sunxi_i2c_adap_init()2553 - init
[    0.078179] sunxi_i2c_probe()2213 - [i2c2] warning: failed to get regulator id
[    0.078233] sunxi_i2c_probe()2281 - [i2c2] no_suspend = 0
[    0.078244] twi2 supply twi not found, using dummy regulator
[    0.078312] twi_request_gpio()452 - [i2c2] init name: twi2
[    0.078811] sunxi_i2c_probe()2213 - [i2c3] warning: failed to get regulator id
[    0.078855] sunxi_i2c_probe()2281 - [i2c3] no_suspend = 0
[    0.078865] twi3 supply twi not found, using dummy regulator
[    0.078910] twi_request_gpio()452 - [i2c3] init name: twi3
[    0.079327] sunxi_i2c_probe()2213 - [i2c4] warning: failed to get regulator id
[    0.079369] sunxi_i2c_probe()2281 - [i2c4] no_suspend = 1
[    0.079379] twi4 supply twi not found, using dummy regulator
[    0.079427] twi_request_gpio()452 - [i2c4] init name: twi4
[    0.080519] axp20x-i2c 4-0034: AXP20x variant AXP2101 found
[    0.082062] axp2101-regulator axp2101-regulator.0: Setting DCDC frequency for unsupported AXP variant
[    0.082070] axp2101-regulator axp2101-regulator.0: Error setting dcdc frequency: -22
[    0.092938] axp2101-aldo2: Bringing 2800000uV into 1800000-1800000uV
[    0.099208] random: fast init done
[    0.106865] axp20x-i2c 4-0034: AXP20X driver loaded
[    0.109427] ion_parse_dt_heap_common: id 0 type 0 name sys_user align 1000
[    0.109604] ion_parse_dt_heap_common: id 1 type 1 name sys_contig align 1000
[    0.109901] ion_parse_dt_heap_common: id 4 type 4 name cma align 1000
[    0.110619] Advanced Linux Sound Architecture Driver Initialized.
[    0.112358] ly_dev_probe
[    0.112436] get bt_wifi_pwrkey_gpio fail
[    0.112984] ws2812b_drv_init
[    0.113777] ly_encryh_init
[    0.114027] 4g power off
[    0.114776] clocksource: Switched to clocksource arch_sys_counter
[    0.116737] get androidboot.mode fail
[    0.116865] NET: Registered protocol family 2
[    0.117483] TCP established hash table entries: 16 (order: -6, 64 bytes)
[    0.117491] TCP bind hash table entries: 16 (order: -6, 64 bytes)
[    0.117496] TCP: Hash tables configured (established 16 bind 16)
[    0.117540] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.117552] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.117698] NET: Registered protocol family 1
[    0.118141] sunxi_spi_probe()2322 - [spi0] SPI MASTER MODE
[    0.118202] spi0 supply spi not found, using dummy regulator
[    0.118257] sunxi_spi_request_gpio()1948 - [spi0] Pinctrl init spi0
[    0.118320] sunxi_spi_clk_init()1998 - [spi0] mclk 300000000
[    0.119299] spi spi0: master is unqueued, this is deprecated
[    0.119591] sunxi_spi_probe()2403 - [spi0]: driver probe succeed, base c882e000, irq 303
[    0.121566] workingset: timestamp_bits=30 max_order=15 bucket_order=0
[    0.130849] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.130857] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.140090] NET: Registered protocol family 38
[    0.140116] io scheduler noop registered
[    0.140119] io scheduler deadline registered
[    0.140342] io scheduler cfq registered (default)
[    0.147053] uart uart0: get regulator failed
[    0.147076] uart0 supply uart not found, using dummy regulator
[    0.147269] uart0: ttyS0 at MMIO 0x5000000 (irq = 294, base_baud = 1500000) is a SUNXI
[    0.147287] sw_console_setup()1908 - console setup baud 115200 parity n bits 8, flow n
[    0.147345] console [ttyS0] enabled
[    0.147962] uart uart3: get regulator failed
[    0.147985] uart3 supply uart not found, using dummy regulator
[    0.148138] uart uart3: dma_tx_buffer c8819000
[    0.148144] uart uart3: dma_tx_phy 0x47c00000
[    0.148157] uart uart3: sw_uart_init_dma_tx sucess
[    0.148197] uart3: ttyS3 at MMIO 0x5000c00 (irq = 295, base_baud = 1500000) is a SUNXI
[    0.149424] sunxi-wlan wlan: wlan_busnum (1)
[    0.149433] sunxi-wlan wlan: wlan_power_num (-1)
[    0.149439] sunxi-wlan wlan: Missing wlan_io_regulator.
[    0.149444] sunxi-wlan wlan: io_regulator_name ((null))
[    0.149455] sunxi-wlan wlan: request pincrtl handle for device [wlan] failed
[    0.149461] sunxi-wlan wlan: get gpio wlan_regon failed
[    0.149499] sunxi-wlan wlan: chip_en gpio=199  mul-sel=1  pull=0  drv_level=1  data=0
[    0.149527] sunxi-wlan wlan: get gpio wlan_hostwake failed
[    0.149534] sunxi-wlan wlan: clk_name ()
[    0.151098] m25p_probe max_speed_hz=50000000
[    0.151189] m25p80 spi0.0: found w25q128, expected m25p80
[    0.151199] m25p80 spi0.0: w25q128 (16384 Kbytes)
[    0.151248] m25p80 spi0.0: w25q128 read unique id bytes: e46250a6c7375b21
[    0.151289] unique_id=e46250a6c7375b21
[    0.155513] 8 sunxipart partitions found on MTD device spi0.0
[    0.155519] Creating 8 MTD partitions on "spi0.0":
[    0.155528] 0x000000000000-0x000000060000 : "uboot"
[    0.156630] 0x000000060000-0x0000000a0000 : "env"
[    0.157817] 0x0000000a0000-0x0000002c0000 : "boot"
[    0.159077] 0x0000002c0000-0x0000004e0000 : "recovery"
[    0.160319] 0x0000004e0000-0x0000007e0000 : "rootfs"
[    0.161598] 0x0000007e0000-0x000000e20000 : "customer"
[    0.162853] 0x000000e20000-0x000000e30000 : "private"
[    0.164131] 0x000000e30000-0x000001057e00 : "UDISK"
[    0.164139] mtd: partition "UDISK" extends beyond the end of device "spi0.0" -- size truncated to 0x1d0000
[    0.165629] tun: Universal TUN/TAP device driver, 1.6
[    0.165634] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[    0.166009] usbcore: registered new interface driver catc
[    0.166099] usbcore: registered new interface driver cdc_ether
[    0.166191] usbcore: registered new interface driver rndis_host
[    0.166199] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.166532] [sunxi-ehci0]: probe, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xc05647d0, 0x:c88b2000, irq_no:12c
[    0.166537] sunxi_insmod_ehci line=657
[    0.166551] sunxi_insmod_ehci line=665
[    0.166588] sunxi_insmod_ehci line=682
[    0.166598] sunxi-ehci 5101000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.166632] sunxi-ehci 5101000.ehci0-controller: new USB bus registered, assigned bus number 1
[    0.166799] sunxi-ehci 5101000.ehci0-controller: irq 300, io mem 0xc05647d0
[    0.194803] sunxi-ehci 5101000.ehci0-controller: USB 0.0 started, EHCI 1.00
[    0.194890] usb_get_configuration bNumConfigurations=1
[    0.194942] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.194950] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.194955] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.194960] usb usb1: Manufacturer: Linux 4.9.118 ehci_hcd
[    0.194965] usb usb1: SerialNumber: sunxi-ehci
[    0.195647] hub 1-0:1.0: USB hub found
[    0.195679] hub 1-0:1.0: 1 port detected
[    0.195902] sunxi_insmod_ehci line=690
[    0.195921] [ehci0-controller]: sunxi_usb_disable_ehci
[    0.195927] [sunxi-ehci0]: remove, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xc05647d0
[    0.195945] sunxi-ehci 5101000.ehci0-controller: remove, state 1
[    0.195958] usb usb1: USB disconnect, device number 1
[    0.196863] sunxi-ehci 5101000.ehci0-controller: USB bus 1 deregistered
[    0.196905] sunxi_insmod_ehci line=717
[    0.197241] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    0.197636] [sunxi-ohci0]: probe, pdev->name: 5101000.ohci0-controller, sunxi_ohci: 0xc0563f80
[    0.197684] sunxi-ohci 5101000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.197717] sunxi-ohci 5101000.ohci0-controller: new USB bus registered, assigned bus number 1
[    0.197762] sunxi-ohci 5101000.ohci0-controller: irq 301, io mem 0xc0324c14
[    0.268855] usb_get_configuration bNumConfigurations=1
[    0.268921] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[    0.268928] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.268934] usb usb1: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.268939] usb usb1: Manufacturer: Linux 4.9.118 ohci_hcd
[    0.268944] usb usb1: SerialNumber: sunxi-ohci
[    0.269597] hub 1-0:1.0: USB hub found
[    0.269631] hub 1-0:1.0: 1 port detected
[    0.269840] [ohci0-controller]: sunxi_usb_disable_ohci
[    0.269847] [sunxi-ohci0]: remove, pdev->name: 5101000.ohci0-controller, sunxi_ohci: 0xc0563f80
[    0.269852] sunxi-ohci 5101000.ohci0-controller: remove, state 1
[    0.269869] usb usb1: USB disconnect, device number 1
[    0.270373] sunxi-ohci 5101000.ohci0-controller: USB bus 1 deregistered
[    0.270939] usbcore: registered new interface driver usbserial
[    0.271028] usbcore: registered new interface driver usbserial_generic
[    0.271111] usbserial: USB Serial support registered for generic
[    0.271190] usbcore: registered new interface driver option
[    0.271266] usbserial: USB Serial support registered for GSM modem (1-port)
[    0.271360] usb_serial_number:20080411
[    0.271519] i2c /dev entries driver
[    0.272082] sunxi cedar version 0.1
[    0.272170] VE: install start!!!
[    0.272170]
[    0.272280] cedar_ve: cedar-ve the get irq is 291
[    0.272342] VE: line 1811 set the sram data
[    0.272342]
[    0.272701] VE: ve_debug_proc_info:c056539c, data:c7584000, lock:c0565424
[    0.272701]
[    0.272705] VE: install end!!!
[    0.272705]
[    0.273060] google_vp9: sunxi google vp9 version 0.1
[    0.273560] axp2101_charger: can not register axp2101-charger without irq
[    0.273560]
[    0.273577] axp2101-power-supply: probe of axp2101-power-supply.0 failed with error -22
[    0.274228] sunxi-wdt 30090a0.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
[    0.275366] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0
[    0.275377] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0
[    0.275387] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:uart0
[    0.275397] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0
[    0.275406] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:uart0
[    0.275416] sun8iw19p1-pinctrl pio: expect_func as:uart0_jtag, but muxsel(3) is func:jtag0
[    0.275677] sunxi-mmc sdc0: SD/MMC/SDIO Host Controller Driver(v3.36 2019-11-26 20:26)
[    0.275682] sunxi_mmc_probe name=sdc0 sdcard is disable
[    0.275717] sunxi-mmc: probe of sdc0 failed with error -1
[    0.276007] sunxi-mmc sdc1: SD/MMC/SDIO Host Controller Driver(v3.36 2019-11-26 20:26)
[    0.276140] sunxi-mmc sdc1: No vmmc regulator found
[    0.276145] sunxi-mmc sdc1: No vqmmc regulator found
[    0.276150] sunxi-mmc sdc1: No vdmmc regulator found
[    0.276154] sunxi-mmc sdc1: No vd33sw regulator found
[    0.276158] sunxi-mmc sdc1: No vd18sw regulator found
[    0.276162] sunxi-mmc sdc1: No vq33sw regulator found
[    0.276166] sunxi-mmc sdc1: No vq18sw regulator found
[    0.276178] sunxi-mmc sdc1: Cann't get uart0 pinstate,check if needed
[    0.276684] sunxi-mmc sdc1: set host busy
[    0.276734] mmc:failed to get gpios
[    0.276949] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.276977] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[    0.304881] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.334789] sunxi-mmc sdc1: detmode:manually by software
[    0.335622] sunxi-mmc sdc1: smc 0 p1 err, cmd 52, RTO !!
[    0.335924] logger: created 1024K log 'log_main'
[    0.336458] sunxi-mmc sdc1: smc 0 p1 err, cmd 52, RTO !!
[    0.336484] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.337822] digital_vol:0, lineout_vol:31, main_gain:23, pa_msleep:160, pa_level:1
[    0.337831] adcdrc_cfg:0, adchpf_cfg:1, dacdrc_cfg:1, dachpf:0
[    0.337890] sunxi-internal-codec codec: [sunxi_internal_codec_probe] codec probe finished.
[    0.338961] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.340455] sunxi_codec_init-->
[    0.340514] [sunxi_card_init] card init finished.
[    0.340844] sunxi-mmc sdc1: smc 0 p1 err, cmd 8, RTO !!
[    0.340860] sunxi-codec-machine sndcodec: sun8iw19codec <-> codec mapping ok
[    0.345627] sunxi-mmc sdc1: smc 0 p1 err, cmd 5, RTO !!
[    0.346451] sunxi-mmc sdc1: smc 0 p1 err, cmd 5, RTO !!
[    0.347268] sunxi-mmc sdc1: smc 0 p1 err, cmd 5, RTO !!
[    0.348083] sunxi-mmc sdc1: smc 0 p1 err, cmd 5, RTO !!
[    0.348901] sunxi-mmc sdc1: smc 0 p1 err, cmd 55, RTO !!
[    0.349715] sunxi-mmc sdc1: smc 0 p1 err, cmd 55, RTO !!
[    0.350531] sunxi-mmc sdc1: smc 0 p1 err, cmd 55, RTO !!
[    0.351345] sunxi-mmc sdc1: smc 0 p1 err, cmd 55, RTO !!
[    0.351361] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm OD pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    0.352255] sunxi-mmc sdc1: smc 0 p1 err, cmd 1, RTO !!
[    0.352272] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
[    0.422051] sunxi-codec-machine sndcodec: [sunxi_card_dev_probe] register card finished.
[    0.422344] Netfilter messages via NETLINK v0.30.
[    0.422355] nfnl_acct: registering with nfnetlink.
[    0.422614] nf_conntrack version 0.5.0 (2048 buckets, 8192 max)
[    0.422982] ctnetlink v0.93: registering with nfnetlink.
[    0.423228] nf_tables: (c) 2007-2009 Patrick McHardy <[email protected]>
[    0.423418] ipip: IPv4 and MPLS over IPv4 tunneling driver
[    0.424082] gre: GRE over IPv4 demultiplexor driver
[    0.424087] ip_gre: GRE over IPv4 tunneling driver
[    0.425800] IPv4 over IPsec tunneling driver
[    0.426570] ip_tables: (C) 2000-2006 Netfilter Core Team
[    0.426671] ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully
[    0.426693] arp_tables: arp_tables: (C) 2002 David S. Miller
[    0.426732] Initializing XFRM netlink socket
[    0.427551] NET: Registered protocol family 10
[    0.429371] mip6: Mobile IPv6
[    0.429400] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    0.430418] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    0.432086] ip6_gre: GRE over IPv6 tunneling driver
[    0.433066] NET: Registered protocol family 17
[    0.433096] NET: Registered protocol family 15
[    0.433182] Bridge firewalling registered
[    0.433335] l2tp_core: L2TP core driver, V2.0
[    0.433340] l2tp_netlink: L2TP netlink interface
[    0.433871] batman_adv: B.A.T.M.A.N. advanced 2016.4 (compatibility version 15) loaded
[    0.433877] openvswitch: Open vSwitch switching datapath
[    0.434210] mpls_gso: MPLS GSO support
[    0.434680] Registering SWP/SWPB emulation handler
[    0.441554] axp2101-rtcldo1: disabling
[    0.441718] hci: ERR: sunxi_ehci is disable, can not disable again
[    0.441721] hci: ERR: sunxi_ohci is disable, can not disable again
[    0.441724] [ehci0-controller]: sunxi_usb_enable_ehci
[    0.441733] [sunxi-ehci0]: probe, pdev->name: 5101000.ehci0-controller, sunxi_ehci: 0xc05647d0, 0x:c88b2000, irq_no:12c
[    0.441736] sunxi_insmod_ehci line=657
[    0.441751] sunxi_insmod_ehci line=665
[    0.441786] sunxi_insmod_ehci line=682
[    0.441816] sunxi-ehci 5101000.ehci0-controller: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.441848] sunxi-ehci 5101000.ehci0-controller: new USB bus registered, assigned bus number 1
[    0.442203] sunxi-ehci 5101000.ehci0-controller: irq 300, io mem 0xc0404bb0
[    0.443320] axp2101-cpusldo: disabling
[    0.443939] ALSA device list:
[    0.443943]   #0: sun8iw19-codec
[    0.446458] VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
[    0.449255] devtmpfs: mounted
[    0.449500] Freeing unused kernel memory: 148K
[    0.449504] This architecture does not have kernel memory protection.
[    0.464834] sunxi-ehci 5101000.ehci0-controller: USB 0.0 started, EHCI 1.00
[    0.464924] usb_get_configuration bNumConfigurations=1
[    0.464984] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    0.464992] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.464997] usb usb1: Product: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[    0.465002] usb usb1: Manufacturer: Linux 4.9.118 ehci_hcd
[    0.465007] usb usb1: SerialNumber: sunxi-ehci
[    0.465661] hub 1-0:1.0: USB hub found
[    0.465697] hub 1-0:1.0: 1 port detected
[    0.465917] sunxi_insmod_ehci line=690
[    0.465938] sunxi_insmod_ehci line=717
[    0.465942] [ohci0-controller]: sunxi_usb_enable_ohci
[    0.465948] [sunxi-ohci0]: probe, pdev->name: 5101000.ohci0-controller, sunxi_ohci: 0xc0563f80
[    0.465992] sunxi-ohci 5101000.ohci0-controller: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.466018] sunxi-ohci 5101000.ohci0-controller: new USB bus registered, assigned bus number 2
[    0.466050] sunxi-ohci 5101000.ohci0-controller: irq 301, io mem 0xc70843fc
[    0.538962] usb_get_configuration bNumConfigurations=1
[    0.539021] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    0.539132] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    0.539139] usb usb2: Product: SW USB2.0 'Open' Host Controller (OHCI) Driver
[    0.539145] usb usb2: Manufacturer: Linux 4.9.118 ohci_hcd
[    0.539150] usb usb2: SerialNumber: sunxi-ohci
[    0.540473] hub 2-0:1.0: USB hub found
[    0.540509] hub 2-0:1.0: 1 port detected
[    1.687026] show_ly_4g_module,hw_cfg1=1
[    1.692204] show_ly_rt8761_module,hw_cfg2=1
[    1.924819] 4g power on
[    1.937152] random: crng init done
[    2.117434] sunxi-ehci 5101000.ehci0-controller: ehci_irq: highspeed device connect
[    2.354814] usb 1-1: new high-speed USB device number 2 using sunxi-ehci
[    2.405232] otg force quirks
[    2.405486] usb_get_configuration bNumConfigurations=1
[    2.405737] usb 1-1: language id specifier not provided by device, defaulting to English
[    2.406233] usb 1-1: New USB device found, idVendor=1782, idProduct=4d12
[    2.406241] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    2.406246] usb 1-1: Product: NEOWAY-N58
[    2.406252] usb 1-1: Manufacturer: NEOWAY
[    4.116979] sunxi-ehci 5101000.ehci0-controller: ehci_irq: highspeed device disconnect
[    4.117066] usb 1-1: USB disconnect, device number 2
[    4.919042] sunxi-ehci 5101000.ehci0-controller: ehci_irq: highspeed device connect
[    5.174822] usb 1-1: new high-speed USB device number 3 using sunxi-ehci
[    5.225109] otg force quirks
[    5.225379] usb_get_configuration bNumConfigurations=1
[    5.225607] usb 1-1: language id specifier not provided by device, defaulting to English
[    5.226109] usb 1-1: New USB device found, idVendor=2949, idProduct=7401
[    5.226124] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    5.226130] usb 1-1: Product: NEOWAY-N58
[    5.226135] usb 1-1: Manufacturer: NEOWAY
[    5.228366] rndis_host 1-1:1.0: status ep2in, 8 bytes period 16
[    5.229123] rndis_host 1-1:1.0 eth0: register 'rndis_host' at usb-sunxi-ehci-1, RNDIS device, f0:4b:b3:b9:eb:e5
[    5.229131] gooo usb ncm probe ok! flags=0x1038 idVendor=0x2949
[    5.229995] option 1-1:1.4: GSM modem (1-port) converter detected
[    5.230579] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[    5.231261] option 1-1:1.5: GSM modem (1-port) converter detected
[    5.231903] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1
[    5.948782] sunxi-wlan wlan: bus_index: 1
[    5.948814] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B
[    5.948904] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[    5.974884] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.005606] sunxi-mmc sdc1: smc 0 p1 err, cmd 52, RTO !!
[    6.006434] sunxi-mmc sdc1: smc 0 p1 err, cmd 52, RTO !!
[    6.006452] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.008895] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.010754] sunxi-mmc sdc1: smc 0 p1 err, cmd 8, RTO !!
[    6.011100] sunxi-mmc sdc1: card claims to support voltages below defined range
[    6.012773] sunxi-mmc sdc1: sdc set ios:clk 0Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.012808] sunxi-mmc sdc1: no vqmmc,Check if there is regulator
[    6.034784] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B
[    6.045769] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 4 timing LEGACY(SDR12) dt B
[    6.046488] sunxi-mmc sdc1: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 4 timing UHS-DDR50 dt B
[    6.046538] sunxi-mmc sdc1: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing UHS-DDR50 dt B
[    6.047281] mmc0: new ultra high speed DDR50 SDIO card at address 0001
[    6.844518] start_addr=(0x8000), end_addr=(0x10000), buffer_size=(0x8000), smp_number_max=(4096)
[    8.125334] cedar_ve: VE real_fre=300000000
[    8.133615] sunxi_i2c_do_xfer()1939 - [i2c3] incomplete xfer (status: 0x30, dev addr: 0x1c)
[    9.174189] ly_update_status= 0
[   10.358918] cedar_ve: VE real_fre=300000000
[   10.565074] store_4g_power_ctrl= 2
[   10.565095] 4g power off
[   10.575602] sunxi-ehci 5101000.ehci0-controller: ehci_irq: highspeed device disconnect
[   10.575686] usb 1-1: USB disconnect, device number 3
[   10.575798] rndis_host 1-1:1.0 eth0: unregister 'rndis_host' usb-sunxi-ehci-1, RNDIS device
[   10.595999] option1 ttyUSB0: GSM modem (1-port) converter now disconnected from ttyUSB0
[   10.596048] option 1-1:1.4: device disconnected
[   10.596702] option1 ttyUSB1: GSM modem (1-port) converter now disconnected from ttyUSB1
[   10.596754] option 1-1:1.5: device disconnected
[   12.420133] sunxi_i2c_do_xfer()1939 - [i2c2] incomplete xfer (status: 0x48, dev addr: 0x10)
[   12.426332] sunxi_i2c_do_xfer()1939 - [i2c2] incomplete xfer (status: 0x48, dev addr: 0x10)
[   13.771997] store_4g_power_ctrl= 1
[   14.408193] ws2812b_led_ctrl set rgb[2]=0x4000
[   15.044801] 4g power on
[   15.335088] sunxi-ehci 5101000.ehci0-controller: ehci_irq: highspeed device connect
[   15.574797] usb 1-1: new high-speed USB device number 4 using sunxi-ehci
[   15.625105] otg force quirks
[   15.625356] usb_get_configuration bNumConfigurations=1
[   15.625601] usb 1-1: language id specifier not provided by device, defaulting to English
[   15.626105] usb 1-1: New USB device found, idVendor=1782, idProduct=4d12
[   15.626112] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   15.626118] usb 1-1: Product: NEOWAY-N58
[   15.626123] usb 1-1: Manufacturer: NEOWAY
[   17.334729] sunxi-ehci 5101000.ehci0-controller: ehci_irq: highspeed device disconnect
[   17.334828] usb 1-1: USB disconnect, device number 4
[   18.136794] sunxi-ehci 5101000.ehci0-controller: ehci_irq: highspeed device connect
[   18.374800] usb 1-1: new high-speed USB device number 5 using sunxi-ehci
[   18.425105] otg force quirks
[   18.425370] usb_get_configuration bNumConfigurations=1
[   18.425602] usb 1-1: language id specifier not provided by device, defaulting to English
[   18.426105] usb 1-1: New USB device found, idVendor=2949, idProduct=7401
[   18.426112] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   18.426117] usb 1-1: Product: NEOWAY-N58
[   18.426122] usb 1-1: Manufacturer: NEOWAY
[   18.428361] rndis_host 1-1:1.0: status ep2in, 8 bytes period 16
[   18.429148] rndis_host 1-1:1.0 eth0: register 'rndis_host' at usb-sunxi-ehci-1, RNDIS device, f0:4b:b3:b9:eb:e5
[   18.429158] gooo usb ncm probe ok! flags=0x1038 idVendor=0x2949
[   18.430088] option 1-1:1.4: GSM modem (1-port) converter detected
[   18.432079] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0
[   18.432568] option 1-1:1.5: GSM modem (1-port) converter detected
[   18.433196] usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1

checksec

FILE	RELRO	S. CANARY	NX	PIE	RPATH	RUNPATH	SYMBOLS	FORTIFY	Fortified	Fortifiable
./bin/adbd	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./bin/busybox	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./lib/libc.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./lib/libgcc_s.so.1	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./lib/liblog.so	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./lib/libstdc++.so.6.0.22	⚠️(Partial)	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./lib/libubox.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./lib/libubus.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./lib/modules/4.9.118/8821cs.ko	❌	✅	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./lib/modules/4.9.118/atm.ko	❌	✅	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./lib/modules/4.9.118/br2684.ko	❌	✅	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./lib/modules/4.9.118/crc-ccitt.ko	❌	❌	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./lib/modules/4.9.118/ecb.ko	❌	❌	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./mnt/customer/app/dnssd	❌	❌	✅	❌	✅	✅	✅	❌	0	6
./mnt/customer/app/gocsdk	❌	✅	✅	✅	✅	✅	✅	❌	0	14
./mnt/customer/app/libGbtsTask.so	❌	❌	❌	⚠️ (DSO)	✅	✅	✅	❌	0	17
./mnt/customer/app/libcarplay.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	24
./mnt/customer/app/libdns_sd.so	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	7
./mnt/customer/app/libiap.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	9
./mnt/customer/app/liblylinkaa.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	4
./mnt/customer/app/liblylinkclient.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	2
./mnt/customer/app/libprotobuf-lite.so.8	❌	❌	✅	⚠️ (DSO)	❌	✅	✅	❌	0	6
./mnt/customer/app/lylinkapp	✅	❌	✅	❌	✅	✅	✅	❌	0	11
./mnt/customer/app/lylinkui	✅	✅	✅	❌	✅	✅	✅	❌	0	14
./mnt/customer/app/mdnsd	❌	❌	✅	❌	✅	✅	✅	❌	0	12
./mnt/customer/app/ui/libcrypto.so.1.1	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	11
./mnt/customer/app/ui/liblylinkav.so	❌	✅	✅	⚠️ (DSO)	✅	✅	✅	❌	0	14
./mnt/customer/app/ui/liblylinkmw.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	5
./mnt/customer/app/ui/liblylinkpcm.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	7
./mnt/customer/app/ui/liblylinkserver.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	1
./mnt/customer/app/ui/liblylinkui.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	12
./mnt/customer/app/ui/liblymodel.so	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	8
./mnt/customer/app/ui/libssl.so.1.1	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	5
./mnt/customer/app/ui/libwebsockets.so.15	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	16
./mnt/customer/app/update	❌	✅	✅	❌	✅	✅	✅	❌	0	7
./mnt/customer/eyesee-mpp/libasound.so.2	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libasound.so.2.0.0	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libaw_aacdec.so	❌	❌	❌	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libaw_g711adec.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libaw_g711udec.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libaw_mp3dec.so	❌	❌	❌	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libaw_wavdec.so	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libcdx_base.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libcdx_common.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libcdx_parser.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libcdx_stream.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libcutils.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libhwdisplay.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libion.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/librgb_ctrl.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libsample_confparser.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/eyesee-mpp/libsmartlink.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./mnt/customer/modules/8821cs.ko	❌	✅	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./mnt/customer/modules/atm.ko	❌	✅	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./mnt/customer/modules/br2684.ko	❌	✅	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./mnt/customer/modules/crc-ccitt.ko	❌	❌	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./mnt/customer/modules/ecb.ko	❌	❌	❌	⚠️ (REL)	✅	✅	❌	❌	0	0
./mnt/customer/ota/www/cgi-bin/index.cgi	❌	✅	✅	❌	✅	✅	✅	❌	0	9
./sbin/logcat	❌	❌	✅	❌	✅	✅	✅	❌	0	0
./sbin/logwrapper	❌	❌	✅	❌	✅	✅	✅	❌	0	0
./sbin/update	❌	✅	✅	❌	✅	✅	✅	❌	0	7
./usr/bin/civetweb	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/client	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/jsonfilter	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/lrz	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/lsz	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/newfs_msdos	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/ota-burnboot0	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/ota-burnuboot	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/progress	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/reboot_efex	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/resolveip	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/swupdate	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/bin/wget-nossl	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/lib/libconfig.so.9.1.3	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libglog.so.0.0.0	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libip4tc.so.0.1.0	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libip6tc.so.0.1.0	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libiptext.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libiptext4.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libiptext6.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libjson-c.so.2.0.1	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libnl-3.so.200.16.1	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libnl-genl-3.so.200.16.1	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libnl-tiny.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libota-burnboot.so	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libpcre.so.1.2.6	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libwebsockets.so.15	❌	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	15
./usr/lib/libxtables.so.10.0.0	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/lib/libz.so.1.2.8	✅	❌	✅	⚠️ (DSO)	✅	✅	✅	❌	0	0
./usr/ota/www/cgi-bin/index.cgi	❌	✅	✅	❌	✅	✅	✅	❌	0	9
./usr/sbin/fw_printenv	❌	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/hostapd	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/jffs2dump	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/jffs2reader	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/mdnsd	❌	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/mkfs.jffs2	✅	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/wpa_cli	❌	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/wpa_supplicant	❌	❌	✅	❌	✅	✅	✅	❌	0	0
./usr/sbin/xtables-multi	✅	❌	✅	❌	✅	✅	✅	❌	0	0