The Subdue graph miner discovers highly-compressing patterns in an input graph. Compression is measured by the reduction in graph size after replacing each instance of the pattern with a single node. This version of Subdue can also find temporal patterns, i.e., the instances of the pattern also match in terms of the arrival order of the nodes and edges that comprise the pattern.
Subdue is designed to accept input graphs in the format produced by the Graph Stream Generator.
Author: Dr. Larry Holder, School of Electrical Engineering and Computer Science, Washington State University, email: [email protected].
Support: This material is based upon work supported by the National Science Foundation under Grant No. 1646640.
Subdue is run using the following command-line format:
python Subdue.py [options] <inputfile>
The options, input file format and output are described below.
The following options are available in Subdue.
--beam <n>
Number of patterns to retain after each expansion of previous patterns; based on their compression value. Default is 4.
--iterations <n>
Number of iterations of Subdue's discovery process. If more than 1, Subdue compresses the graph with the best pattern and then runs again using the compressed graph. If 0, then Subdue runs until no more compression (i.e., set to |E|). Default is 1.
--limit <n>
Number of patterns considered in each iteration of Subdue. A value of 0 implies |E|/2. Default is 0.
--maxsize <n>
Maximum size (#edges) of a pattern. A value of 0 implies |E|/2. Default is 0.
--minsize <n>
Minimum size (#edges) of a pattern. Default is 1.
--numbest <n>
Number of best patterns to report at end. Default is 3.
--prune
If enabled, Subdue removes any pattern whose value is worse than its parent pattern. Disabled by default.
--temporal
If enabled, Subdue discovers temporal patterns, i.e., patterns whose instances are not only isomorphic, but also match in terms of their vertex and edge arrival order. Disabled by default (i.e., static patterns that ignore timestamps).
--valuebased
If enabled, then all patterns with the top beam values are retained during the discovery process. Disabled by default.
--writecompressed
If enabled, Subdue writes the compressed graph after each iteration i to the file outputFileName-compressed-i.json, where outputFileName is the same as the input file name, but with .json removed if present. Disabled by default.
--writeinstances
If enabled, Subdue writes instances of the best pattern at iteration i as one graph to file outputFileName-instances-i.json. Disabled by default.
--writepattern
If enabled, Subdue writes the best pattern at iteration i to file outputFileName-pattern-i.json. Disabled by default.
The input file represents a graph in JSON format. An example is in the file inputgraph.json, and a visualization of this graph is in inputgraph.png. The input graph contains a JSON array of vertices and edges, as described below.
A vertex is a JSON object with name "vertex" and whose value is a JSON object with the following properties.
- id: A string identifier that uniquely identifies this vertex.
- attributes: A JSON object of name/value pairs, where both the name and value are strings. For two vertices to match, all of their attributes must match.
- timestamp: An integer value (as a string) representing the time at which this vertex first appeared in the graph. Timestamps are only used if Subdue is run with the --temporal option.
An edge is a JSON object with name "edge" and whose value is a JSON object with the following properties.
- id: A string identifier that uniquely identifies this edge.
- source: Vertex identifier string for the edge's source vertex.
- target: Vertex identifier string for the edge's target vertex.
- directed: Whether the edge is directed from source to target ("true"), or undirected ("false").
- attributes: A JSON object of name/value pairs, where both the name and value are strings. For two edges to match, all of their attributes must match.
- timestamp: An integer value (as a string) representing the time at which this edge first appeared in the graph. Timestamps are only used if Subdue is run with the --temporal option.
Subdue outputs the top patterns according to their compression value along with their instances in the input graph. The file output.txt contains the output produced by Subdue on inputgraph.json using default options.
Contact: Dr. Larry Holder, School of Electrical Engineering and Computer Science, Washington State University, email: [email protected].