The purpose of this project is to collect from SMA solar inverters using an RS485 connection and send the data to your cloud using Ardexa. Data from SMA solar inverters is read using a Linux device such as a Raspberry Pi, or an X86 intel powered computer.
This application is written in C++, using the SMA provided C libraries to query SMA inverters connected via RS485. This application will run as a service, and query any number of connected inverters at regular intervals. Data will be written to log files on disk in a directory specified via the command line. Usage and command line parameters are as follows. Note that the applications should be run as root only since it has access to a device in the /dev directory.
Usage: sudo ardexa-sma -c conf file path -n number of devices [-l log directory] [-d] [-v] [-i] [-s number of seconds between readings]
-l (optional) <directory> name for the location of the directory in which the logs will be written. The default is `/opt/ardexa/sma/logs`
-c (mandatory) <file path> fullpath of the SMA config file. An explanation of the config file is below.
-d (optional) if specified, debug will be turned on. Default is off.
-i (optional) discovery. Print (and if debug is on, send to the console) a listing of all available objects and variables on all inverters.
-v (optional) prints the version and exits.
-s (optional) delay between readings. Default is 60 seconds. Ignored during discovery (-i option).
-n (mandatory) number of devices to find. Must be at least 1, and less than 40.
The only 2 mandatory items are the number of inverters (-n) and the configuration file -c. So an example of the usage is : sudo ardexa-sma -c /home/ardexa/yasdi.conf -n 1
So for example, to run a discovery:
sudo ardexa-sma -c yasdi.conf -n 1 -i
The SMA (as most inverters) can use RS485 as a means to communicate data and settings RS485 is a signalling protocol that allows many devices to share the same physical pair of wires, in a master master/slave relationship See -> http://www.usb-serial-adapter.org/ for further information
When an RS485 to USB converter has been plugged in, on Linux systems the device will connect to something line /dev/ttyUSB0. To check:
sudo tail -f /var/log/syslog
...then plug in the converter
You should see a line like: usb 1-1.4: ch341-uart converter now attached to ttyUSB0
This means that the RS485 serial port can be accessed by the logical device /dev/ttyUSB0
Alternatively, try: dmesg | grep tty
Reference for the wiring:
If your computer has an RS485 port, then the inverter can be connected directly to this port. The inverter is connected using 3 wires to the RS485 DB9 port on the computer. DO NOT connect the inverter RS485 to a RS232 port. They are not voltage compatible and damage will probably occur. For this to happen, you need a devices like these:
- http://www.robotshop.com/en/db9-female-breakout-board.html
- https://core-electronics.com.au/db9-female-breakout-board.html
- https://www.amazon.com/Female-Breakout-Board-Screw-Terminals/dp/B00CMC1XFU
Each and every RS485 port that uses DB9 has a different pinout. So you have to read the actual manual for the physical RS485 port you are using. For example; if using the Advantech UNO 2362G, the following pins are used: Pin1 = D- , Pin 2 = D+ and Pin 5 = GND. All other pins are not connected, so do not connect any other pins. So to wire it all up:
- Make sure the Advantech is turned off
- D+ Pin from the SMA Inverter (should be Pin 2 on the RS485 inverter interface) to Pin 2 of the RS485 DB-9 (Female) on the Advantech UNO 2362G
- GND Pin from the SMA Inverter (should be Pin 5 on the RS485 inverter interface) to Pin 5 of the RS485 DB-9 (Female) on the Advantech UNO 2362G
- D- Pin from the SMA Inverter (should be Pin 7 on the RS485 inverter interface) to Pin 1 of the RS485 DB-9 (Female) on the Advantech UNO 2362G
Confirm the physical serial port by running the command dmesg | grep tty. As stated previously, it should return something like /dev/ttyS1 if using a serial com port, or something like /dev/ttyUSB0 if using a 485/USB serial converter.
The YASDI software (See: http://www.sma.de/en/products/monitoring-control/yasdi.html) allows communications with the SMA inverter via RS485. Download thre ZIP file and do the following to install the libraries and utlities. You may need to install all the build tools as follows
sudo apt-get update
sudo apt-get install -y build-essential git cmake
then install the YASDI software
cd
mkdir sma
cd sma
...from http://www.sma.de/en/products/monitoring-control/yasdi.html#Downloads
wget yasdi-1.8.1build9-src.zip
unzip yasdi-1.8.1build9-src.zip
edit the file ../yasdi/include/packet.h and change Line 38: from struct TDevice * Device ...to.... struct _TDevice * Device
cd projects/generic-cmake
mkdir build-gcc
cd build-gcc
cmake ..
make
sudo make install
sudo ldconfig
cd
vi yasdi.conf
[DriverModules]
Driver0=yasdi_drv_serial
[COM1]
Device=/dev/ttyUSB0
Media=RS485
Baudrate=1200
Protocol=SMANet
sudo yasdishell yasdi.conf ... just to test
In the 'yasdi.conf' file above, change the 'Device=...' to whatever the device name is, as per the instructions above.
- Make sure the YASDI application is in the directory above
../sma/
cd
git clone https://github.com/ardexa/sma-rs485-inverters.git
cd sma-rs485-inverters
mkdir build
cd build
cmake ..
make
sudo make install
sudo ldconfig
The Ardexa service will query one or all of the inverters. To query at regular intervals, and write a message to the log, a service is required. The following instructions detail how to install the application to run as a service. The attached ardexa-sma.service file is used to run the application as a service. Edit the line ExecStart=/usr/local/bin/ardexa-sma -c /home/ardexa/yasdi.conf -n 13 -s 300 to change the number of inverters that will be searched (the -n 13 parameter) and the time between readings (the -s 300 parameter).
sudo cp ardexa-sma.service /etc/systemd/system/
sudo systemctl enable ardexa-sma.service
sudo systemctl daemon-reload
sudo systemctl restart ardexa-sma.service
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent