Comments (32)
MCUdude
commented on August 24, 2024
1
Avrdude is most likely using an older avrdude.conf file that contains errors.
Please post the entire Avrdude output with the -v flag as well.
from avrdude.
MartinKES
commented on August 24, 2024
1
I have a STK500 (very old) on my desk.
so please wait on hour
from avrdude.
MartinKES
commented on August 24, 2024
1
I have found a AvrISP with serial link
C:\Daten\Test\AvrDude\V7_3>avrdude -p c128 -c stk500v2 -P\.\com5 -t
avrdude> dump ee 0 128
Reading | ################################################## | 100% 0.50 s
0000 01 03 00 00 00 00 00 00 00 00 ff ff ff ff ff ff |................|
0010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
avrdude> dump ee 256 128
Reading | ################################################## | 100% 0.51 s
0100 76 19 10 19 00 00 00 00 00 00 00 00 00 00 00 00 |v...............|
0110 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
0120 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
0130 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
0140 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
0150 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
0160 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
0170 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
avrdude>
Its oll Ok - so my SmartUSB Programmer should be the Problem
Sorry for the inconvenience
Martin Heumann
from avrdude.
MCUdude
commented on August 24, 2024
1
error: (cmd) command 'read is invalid
@MartinKES It looks like your shell doesn't line single quotes. can you try with double quotes instead, for both programmers?
avrdude -p c128 -c stk500v2 -P\\.\com5 -vvvv -T "read eeprom 0 16"
from avrdude.
MartinKES
commented on August 24, 2024
1
@mcuee
"avrdude -p c128 -c stk500v2 -P com9 -U ee:r:EeProm:i" with mySmartUSB light
eeprom.txt
eeprom.txt
"since you mention that IAR Embedded Workbench seems to work fine." that was with AtmelIce Interface
from avrdude.
mcuee
commented on August 24, 2024
@MartinKES
Most likely an old version of avrdude is used.
Are you using Arduino As ISP as the programmer? Please use avrdude 7.3 release and -c arduino_as_isp and try again.
from avrdude.
ndim
commented on August 24, 2024
Question to @MCUdude: An older avrdude.conf in the sense of older than the version of avrdude executable being used, or an older avrdude.conf in the sense of version consistent with the avrdude executable being used but containing unfixed bugs?
Update: Looks like the latter, going by @mcuee's reply.
from avrdude.
MartinKES
commented on August 24, 2024
In version 7.3 the same result
with arduino_as_isp:
avrdude error: programmer is not responding
avrdude warning: attempt 1 of 10: not in sync: resp=0x00
avrdude warning: attempt 2 of 10: not in sync: resp=0xe1
avrdude warning: attempt 3 of 10: not in sync: resp=0xe5
avrdude warning: attempt 4 of 10: not in sync: resp=0xcb
avrdude warning: attempt 5 of 10: not in sync: resp=0x2b
avrdude warning: attempt 6 of 10: not in sync: resp=0xe1
avrdude warning: attempt 7 of 10: not in sync: resp=0xe5
avrdude warning: attempt 8 of 10: not in sync: resp=0xcb
avrdude warning: attempt 9 of 10: not in sync: resp=0x2b
avrdude warning: attempt 10 of 10: not in sync: resp=0xe1
avrdude error: unable to open port \\.\com9 for programmer arduino_as_isp
avrdude error: avrdude built without libserialport support; please compile again with libserialport installed
from avrdude.
MCUdude
commented on August 24, 2024
Question to @MCUdude: An older avrdude.conf in the sense of older than the version of avrdude executable being used, or an older avrdude.conf in the sense of version consistent with the avrdude executable being used but containing unfixed bugs?
A newer Avrdude executable is being used with an older avrdude.conf file, most likely bundled or built for an older Avrdude version.
In version 7.3 the same result
Can you please share the entire output, including the command you ran? It's impossible to say what's going on here. From what I know, the baud rate is incorrect. But that's impossible for me to know because you didn't include the Avrdude command.
from avrdude.
MartinKES
commented on August 24, 2024
C:\Daten\Test\AvrDude\V7_3>avrdude -c stk500 -p AT90CAN128 -P \\.\com9 -t
avrdude: successfully opened stk500v2 device; please use -c stk500v2
avrdude: AVR device initialized and ready to accept instructions
avrdude: device signature = 0x1e9781 (probably c128)
avrdude: processing -t interactive terminal
avrdude> dump ee 0 128
Reading | ################################################## | 100% 0.47 s
0000 01 03 00 00 00 00 00 00 ff ff ff ff ff ff ff ff |................|
0010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
avrdude> quit
avrdude done. Thank you.
C:\Daten\Test\AvrDude\V7_3>avrdude -c arduino_as_isp -p AT90CAN128 -P \\.\com9 -t
avrdude error: programmer is not responding
avrdude warning: attempt 1 of 10: not in sync: resp=0x00
avrdude warning: attempt 2 of 10: not in sync: resp=0xe1
avrdude warning: attempt 3 of 10: not in sync: resp=0xe5
avrdude warning: attempt 4 of 10: not in sync: resp=0xcb
avrdude warning: attempt 5 of 10: not in sync: resp=0x2b
avrdude warning: attempt 6 of 10: not in sync: resp=0xe1
avrdude warning: attempt 7 of 10: not in sync: resp=0xe5
avrdude warning: attempt 8 of 10: not in sync: resp=0xcb
avrdude warning: attempt 9 of 10: not in sync: resp=0x2b
avrdude warning: attempt 10 of 10: not in sync: resp=0xe1
avrdude error: unable to open port \\.\com9 for programmer arduino_as_isp
avrdude error: avrdude built without libserialport support; please compile again with libserialport installed
avrdude done. Thank you.
from avrdude.
mcuee
commented on August 24, 2024
In this case, your programmer is not "Arduino as ISP", but rather using -c stk500v2. What is the prorgrammer used? Is it an original Microchip STK500 kit or an STK500v2 clone? Are you using a bootloader?
Please follow the FAQ here when reporting an issue. Thanks.
https://github.com/avrdudes/avrdude/wiki/FAQ#how-to-report-an-issue-to-avrdude-project
- Tell us what exactly the problem is and how you came to experience it
- OS
- Programmer
- Part
- How host, programmer and part are connected/rigged up
- AVRDUDE binary version used (in bash avrdude -v 2>&1 | grep -i version)
- Full command line including all options
- Output of the command
- Please try to use the latest released version
- You may be requested to try out git main as well
- Sometimes it also helps us if you upload a file with the -vv or -vvvv output
- Sometimes it also helps us if you post the hex file used (if you are okay to share the hex file)
- What you would have expected to happen?
from avrdude.
MCUdude
commented on August 24, 2024
In this case, your programmer is not "Arduino as ISP", but rather using -c stk500v2
It was you that suggested arduino_as_isp, not him. He states that "Readout offset 8, 9 are always 0xFF but should be 0", but Avrdude reports something else.
avrdude: processing -t interactive terminal
avrdude> dump ee 0 128
Reading | ################################################## | 100% 0.47 s
0000 01 03 00 00 00 00 00 00 ff ff ff ff ff ff ff ff |................|
0010 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0020 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0030 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0050 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0060 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0070 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
avrdude> quit
@MartinKES how can you be sure that the actual EEPROM values stored at addresses 8 and 9 should be 0? What makes you think Avrdude reports incorrect data?
from avrdude.
MartinKES
commented on August 24, 2024
- IAR Workbench
- myAVRProgTool
Byte 0 Major Version
Byte 1 Minor Version
Byte 2-5 DWord actual Error Flags
Byte 6-9 DWord ored ErrorFlags
avrdude: processing -t interactive terminal
avrdude> dump ee 8 2
Reading | ################################################## | 100% 0.03 s
0008 ff ff |.. |
avrdude> dump ee 8 2
Reading | ################################################## | 100% 0.00 s
0008 ff ff |.. |
avrdude> dump ee 8 2
Reading | ################################################## | 100% 0.00 s
0008 ff ff |.. |
avrdude> dump ee 8 2
Reading | ################################################## | 100% 0.00 s
0008 ff ff |.. |
avrdude> dump ee 8 2
Reading | ################################################## | 100% 0.00 s
0008 ff ff |.. |
avrdude> dump eeprom 8 2
Reading | ################################################## | 100% 0.00 s
0008 ff ff |.. |
avrdude> dump eeprom 7 4
Reading | ################################################## | 100% 0.03 s
0007 00 ff ff ff |.... |
avrdude> quit
at offset 182 are the next Databytes (Parameters):
Reading | ################################################## | 100% 0.50 s
0008 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0018 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0028 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0038 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0048 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0058 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0068 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................|
0078 ff ff ff ff ff ff ff ff 76 19 10 19 00 00 00 00 |........v.......|
from avrdude.
mcuee
commented on August 24, 2024
In this case, your programmer is not "Arduino as ISP", but rather using -c stk500v2
It was you that suggested
arduino_as_isp, not him. He states that "Readout offset 8, 9 are always 0xFF but should be 0", but Avrdude reports something else.
I was asking whether he was using arduino_as_isp. Anyway, it is critical to know which programmer @MartinKES is using. There are many different flavours of STK500v2 programmers out there.
from avrdude.
MartinKES
commented on August 24, 2024
My programmer is mySmartUSB (www.myAVR.de) light.
from avrdude.
MartinKES
commented on August 24, 2024
Output from atprogram --> JTAG-Ice:
F:\Atmel\atprog\atbackend>atprogram -t atmelice -d at90can128 -i JTAG read -ee -s 128 -o 0
Firmware check OK
:1000000001030000000000000000FFFFFFFFFFFFF2
:10001000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF0
:10002000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFE0
:10003000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFD0
:10004000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFC0
:10005000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFB0
:10006000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFA0
:10007000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF90
:00000001FF
also 10 Bytes : offset 8,9 =0
from avrdude.
MartinKES
commented on August 24, 2024
Output from atprogram --> mySmartUSB light:
F:\Atmel\atprog\atbackend>atprogram -t stk500 -c COM9 -d at90can128 -i ISP read -ee -s 128 -o 0
Firmware check OK
:1000000001030000000000000000FFFFFFFFFFFFF2
:10001000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF0
:10002000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFE0
:10003000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFD0
:10004000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFC0
:10005000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFB0
:10006000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFA0
:10007000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF90
:00000001FF
Programmer I.O.
from avrdude.
MCUdude
commented on August 24, 2024
Can you try to read the EEPROM using -U? Like so:
C:\Daten\Test\AvrDude\V7_3>avrdude -c stk500 -p AT90CAN128 -P \\.\com9 -U eeprom:r:-:i
from avrdude.
MartinKES
commented on August 24, 2024
avrdude: processing -U eeprom:r:-:i
avrdude: reading eeprom memory ...
Reading | ################################################## | 100% 13.86 s
avrdude: writing output file
:200000000103000000000000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF4
:20002000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFE0
:20004000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFC0
:20006000FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFA0
:200080007619101900000000000000000000000000000000000000000000000000000000A8
:2000A000000000000000000000000000000000000000000000000000000000000000000040
:2000C000000000000000000000000000000000000000000000000000000000000000000020
:2000E000000000000000000000000000000000000000000000000000000000000000000000
:200100000000000000000000000000000000000000000000000000000000000000000000DF
from avrdude.
mcuee
commented on August 24, 2024
My programmer is mySmartUSB (www.myAVR.de) light.
The good thing is that you have another programmer Atmel ICE and confirms that there is an issue here.
Now there could be two possibilities.
- avrdude has a bug with
-c stk500v2for AT90CAN128 chip when reading EEPROM - mySmartUSB is not compatible with official STK500v2 FW in terms of EEPROM reading.
We need to check official STK500v2 now to which one is true.
@MCUdude
I could not find my AT90CAN128 board now. Please help here. Thanks.
from avrdude.
MartinKES
commented on August 24, 2024
Sorry RS232 defect on STK500
from avrdude.
MCUdude
commented on August 24, 2024
Its oll Ok - so my SmartUSB Programmer should be the Problem
Thanks for confirming. It's difficult for us to find out what the issue might be, but it's interesting that it works when using atprogram.
As a last test, can you post the entire output of
C:\Daten\Test\AvrDude\V7_3>avrdude -p c128 -c stk500v2 -P\.\com5 -vvvv -T 'read eeprom 0 16'
when using the programmer that reported incorrect data (mySmartUSB), and the programmer that did report correctly (AVRISP with serial link)?
The command above has -vvvv, which lets us see every byte of the data the programmer sends to avrdude.
And -T 'read eeprom 0 16' is just a way to call terminal mode commands without having to do it interactively.
from avrdude.
MartinKES
commented on August 24, 2024
Done with AvrISP (serial):
C:\Daten\Test\AvrDude\V7_3>avrdude -p c128 -c stk500v2 -P\\.\com5 -vvvv -T 'read eeprom 0 16'
avrdude: Version 7.3
Copyright the AVRDUDE authors;
see https://github.com/avrdudes/avrdude/blob/main/AUTHORS
System wide configuration file is C:\Daten\Test\AvrDude\V7_3\avrdude.conf
Using port : \\.\com5
Using programmer : stk500v2
avrdude: ser_send: . [1b] . [01] . [00] . [01] . [0e] . [01] . [14]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [01]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [0b]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [01]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [08]
avrdude: ser_recv: A [41]
avrdude: ser_recv: V [56]
avrdude: ser_recv: R [52]
avrdude: ser_recv: I [49]
avrdude: ser_recv: S [53]
avrdude: ser_recv: P [50]
avrdude: ser_recv: _ [5f]
avrdude: ser_recv: 2 [32]
avrdude: ser_recv: t [74]
avrdude: stk500v2_getsync(): found AVRISP programmer
AVR Part : AT90CAN128
Programming modes : ISP, HVPP, JTAG, JTAGmkI, SPM
Memory Size Pg size
----------------------------
eeprom 4096 8
flash 131072 256
efuse 1 1
hfuse 1 1
lfuse 1 1
lock 1 1
signature 3 1
calibration 1 1
io 224 1
sram 4096 1
Variants Package F max T range V range
-----------------------------------------------------------------
AT90CAN128 N/A 20 MHz [-40 C, 85 C] [4.5 V, N/A]
AT90CAN128-15AZ TQFP64 16 MHz [-40 C, 125 C] [2.7 V, 5.5 V]
AT90CAN128-16AI TQFP64 16 MHz [-40 C, 85 C] [2.7 V, 5.5 V]
AT90CAN128-16AU TQFP64 16 MHz [-40 C, 85 C] [2.7 V, 5.5 V]
AT90CAN128-16AUR TQFP64 16 MHz [-40 C, 85 C] [2.7 V, 5.5 V]
AT90CAN128-16MI QFN64 16 MHz [-40 C, 85 C] [2.7 V, 5.5 V]
AT90CAN128-16MU QFN64 16 MHz [-40 C, 85 C] [2.7 V, 5.5 V]
AT90CAN128-16MUR QFN64 16 MHz [N/A, N/A] [2.7 V, 5.5 V]
Programmer Type : STK500V2
Description : Atmel STK500 version 2.x firmware
Programmer model : AVRISP
avrdude: ser_send: . [1b] . [02] . [00] . [02] . [0e] . [03] . [90] . [86]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [02]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [0f]
avrdude: ser_recv: . [18]
avrdude: ser_send: . [1b] . [03] . [00] . [02] . [0e] . [03] . [91] . [86]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [02]
avrdude: ser_recv: . [14]
avrdude: ser_send: . [1b] . [04] . [00] . [02] . [0e] . [03] . [92] . [82]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [04]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [07]
avrdude: ser_recv: . [16]
HW version : 15
FW Version Controller : 2.07
avrdude: ser_send: . [1b] . [05] . [00] . [02] . [0e] . [03] . [94] . [85]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [05]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [10]
Vtarget : 0.0 V
SCK period : 0.1 us
avrdude: ser_send: . [1b] . [06] . [00] . [0c] . [0e] . [10] . [c8] d [64] . [19] [20] . [00] S [53] . [03] . [ac] S [53] . [00] . [00] 5 [35]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [06]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [02]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [10]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [01]
avrdude: AVR device initialized and ready to accept instructions
Reading | | 0% 0.00 s
avrdude: stk500isp_read_byte(.., signature, 0x0, ...)
avrdude: stk500isp_read_byte(): sending read memory command:
avrdude: ser_send: . [1b] . [07] . [00] . [06] . [0e] . [1b] . [04] 0 [30] . [00] . [00] . [00] ; [3b]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [07]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [04]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [1e]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [13]
avrdude: stk500isp_read_byte(.., signature, 0x1, ...)
avrdude: stk500isp_read_byte(): sending read memory command:
avrdude: ser_send: . [1b] . [08] . [00] . [06] . [0e] . [1b] . [04] 0 [30] . [00] . [01] . [00] 5 [35]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [08]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [04]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [97]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [95]
Reading | ################# | 33% 0.05 s
avrdude: stk500isp_read_byte(.., signature, 0x2, ...)
avrdude: stk500isp_read_byte(): sending read memory command:
avrdude: ser_send: . [1b] . [09] . [00] . [06] . [0e] . [1b] . [04] 0 [30] . [00] . [02] . [00] 7 [37]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [09]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [04]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [81]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [82]
Reading | ################################################## | 100% 0.08 s
avrdude: device signature = 0x1e9781 (probably c128)
avrdude: processing -T 'read
avrdude do_cmd() [term.c:2373] error: (cmd) command 'read is invalid
avrdude: ser_send: . [1b] . [0a] . [00] . [03] . [0e] . [11] . [01] . [01] . [0d]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [0a]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [02]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [11]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [0c]
avrdude done. Thank you.
from avrdude.
mcuee
commented on August 24, 2024
Please do the same with your SmartUSB Programmer. There might be a way to support your programmer if we can differentiate the two in terms of USB VID/PID and the firmware differences when reading the EEPROM.
Edit to add: Also your -T command failed. Please refer to the comment below by @MCUdude.
from avrdude.
mcuee
commented on August 24, 2024
@MartinKES
Other than terminal mode, did you have the same problem with normal mode or not? It could be that normal CLI mode works since you mention that IAR Embedded Workbench seems to work fine.
avrdude -p c128 -c stk500v2 -P com5 -U:eeprom:-:i
from avrdude.
MartinKES
commented on August 24, 2024
Done with AvrDude 7.3 --> mySmartUSB light
... Initialisierung
avrdude> read eeprom 0 16
Reading | | 0% 0.00 s
avrdude: ser_send: . [1b] . [10] . [00] . [05] . [0e] . [06] . [00] . [00] . [00] . [00] . [06]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [10]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [02]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [06]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [01]
avrdude: ser_send: . [1b] . [11] . [00] . [04] . [0e] . [16] . [00] . [08] . [a0] . [be]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [11]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [0b]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [16]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [01]
avrdude: ser_recv: . [03]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [1b]
Reading | ###################### | 43% 0.04 s
avrdude: ser_send: . [1b] . [12] . [00] . [05] . [0e] . [06] . [00] . [00] . [00] . [08] . [0c]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [12]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [02]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [06]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [03]
avrdude: ser_send: . [1b] . [13] . [00] . [04] . [0e] . [16] . [00] . [08] . [a0] . [bc]
avrdude: ser_recv: . [1b]
avrdude: ser_recv: . [13]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [0b]
avrdude: ser_recv: . [0e]
avrdude: ser_recv: . [16]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [ff]
avrdude: ser_recv: . [00]
avrdude: ser_recv: . [1b]
Reading | ################################################## | 100% 0.08 s
0000 01 03 00 00 00 00 00 00 ff ff ff ff ff ff ff ff |................|
avrdude>
from avrdude.
mcuee
commented on August 24, 2024
"since you mention that IAR Embedded Workbench seems to work fine." that was with AtmelIce Interface.
I see,
Then it is clear that the issue is with mySmartUSB light prorgammer, no matter in the normal CLI mode or the Terminal mode.
from avrdude.
mcuee
commented on August 24, 2024
Since myAVRProgTool works fine, if you really want to get your programmer working with avrdude, you probably have to reverse engineering the FW differences between official STK500v2 and mySmartUSB light programmer.
Probably not really worth the effort since you have other well supported programmers with avrdude.
from avrdude.
mcuee
commented on August 24, 2024
Change the title so that it is easier for future references.
from avrdude.
MartinKES
commented on August 24, 2024
What is a good alternative for a programmer (USB to ISP) without drivers?
from avrdude.
mcuee
commented on August 24, 2024
What is a good alternative for a programmer (USB to ISP) without drivers?
There is no such thing as "without drivers" for Windows. Rather you want to use built-in drivers like WinUSB or USB HID.
Cheap and good one: well supported by avrdude: USBASP
You do need to flash the right FW in order to use WinUSB driver out of box.
https://github.com/nerdralph/usbasp
from avrdude.
MartinKES
commented on August 24, 2024
Ok – like the good old AvrIsp (STK500, RS232) interface. For USB a UART-Interface (PL2303, FTDI, …) is enough.
Thanks
Martin
from avrdude.
Related Issues (20)
- usbasp_write_byte in TPI mode; all writes have to be done at page level HOT 15
- cmake enabling LINUXGPIO on ubuntu 20.04 fails HOT 4
- arduino uno atmga328p HOT 2
- macOS github action failed. HOT 9
- CMake improvement -- using pkg-find to find the libraries HOT 1
- format mismatch warnings HOT 3
- Misleading error message: cannot find programmer id
- custom programmer broken in v7.3 HOT 4
- ATtiny11 does not have EEPROM
- Misleading error message when specifying wrong AVR-Ex part HOT 11
- Multi-memory files HOT 13
- AVRDUDE fails to return -1 on certain write byte errors
- UPDI with AtmelICE, how to? HOT 6
- Parallel port silently not working HOT 9
- No way to set fuses for ATTiny 1626 / UPDI ? HOT 1
- Bootrow r/w does not work for `-c serialupdi` HOT 7
- Terminal erase command HOT 8
- JTAGICE3 EDBG communication mode relies on hardcoded USBVID HOT 7
- Unable to flash using Avrdude on a 14'' M1 Macbook Pro HOT 2
- JTAG2UPDI: avrdude error: cannot find programmer id jtag2updi HOT 3
Recommend Projects
-
React
A declarative, efficient, and flexible JavaScript library for building user interfaces.
-
Vue.js
🖖 Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
-
Typescript
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
-
TensorFlow
An Open Source Machine Learning Framework for Everyone
-
Django
The Web framework for perfectionists with deadlines.
-
Laravel
A PHP framework for web artisans
-
D3
Bring data to life with SVG, Canvas and HTML. 📊📈🎉
-
Recommend Topics
-
javascript
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
-
web
Some thing interesting about web. New door for the world.
-
server
A server is a program made to process requests and deliver data to clients.
-
Machine learning
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
-
Visualization
Some thing interesting about visualization, use data art
-
Game
Some thing interesting about game, make everyone happy.
Recommend Org
-
Facebook
We are working to build community through open source technology. NB: members must have two-factor auth.
-
Microsoft
Open source projects and samples from Microsoft.
-
Google
Google ❤️ Open Source for everyone.
-
Alibaba
Alibaba Open Source for everyone
-
D3
Data-Driven Documents codes.
-
Tencent
China tencent open source team.
from avrdude.