diyruz/diyruz_rt

Single relay with ds18b20 sensor for TI cc2530 and Sonoff Zigbee

diyruz_rt's Issues

[REQUEST] Support for Sonoff TH Sensor AM2301 / DHT21 (Humidity and Temperature) sensor for outdoors

Request support for Sonoff TH Sensor AM2301 (Humidity and Temperature) outdoor sensor that comes with a 2.5mm jack

https://sonoff.tech/product/accessories/am2301

Note! DHT21 is another name for AM2301.

Sonoff TH Sensor AM2301 is designed for convenient replacement sold as an official option for Sonoff TH10 and Sonoff TH16

https://www.itead.cc/sonoff-th.html

https://www.itead.cc/wiki/Sonoff_TH_10/16

https://tasmota.github.io/docs/devices/Sonoff-TH/

Sensors for Sonoff TH series comes with a standard 2.5mm jack (Stereo + Mic Audio Connector) which has been repurposed:

Pin	Name	Description
1	VCC	Power supply 2.2~3.6VDC
2	GND	GND
3	NC	NC
4	DATA	Single bus, data port

https://www.itead.cc/wiki/File:Si7021_audio_connector.jpg

Zigbee firmware hex for the Sonoff BASICZBR3 with DS18b20 as Enddevice

Hello,

I test Sonoff ZBR3 with your first release firmare with temperature sensor DS18b20.
I use this relay for control electric heater in water tank.
In HA with mqtt i see temperature from sensor DS18b20.
Generally is working but from time to time i have error 'No network route' and i have to unpair and pair again.
My coordinator is 5m away from ZBR3.
I think there is an issue with two devices (CC2530) struggling to route the signal (they are so weak…). The outcome is that another CC2530 (BlitzWolf BW-SHP13) connects to both of them instead of picking “stronger” routers (that it was connecting before). Finally, it often loses the signal from these Sonoffs DS18b20 with and does not pick the better routers…

Would it be possible to disable the router feature with your firmware as the second release?
So this BASICZBR3 will work as Enddevice ?

For your information i tested firmare "Zigbee Configurable Firmware v2.5" from "PTVO" with router and without router and this modded firmare can't show temperature from sensor DS18b20.

So please add second release with the source code but as only Enddevice.

waiting for your fedback.
Thx
Wojtek

[REQUEST] Support for DHT22 (Humidity and Temperature) sensor

Request support for DHT22 (Humidity and Temperature) sensor:

https://www.itead.cc/humidity-temperature-sensor-dht22.html

DHT22 sensors are more expensive and more accurate than DHT11

Please also see the request for DHT11 support -> #7

[REQUEST] Support for Sonoff TH Sensor Si7021 (Humidity and Temperature) sensor for indoors

Request support for Sonoff TH Sensor Si7021 (Humidity and Temperature) indoor sensor that comes with 2.5mm jack and cable

https://sonoff.tech/product/accessories/Si7021

https://www.itead.cc/wiki/Sonoff_Sensor_Si7021

https://www.itead.cc/wiki/File:Sonoff_Si7021_Sensor_Schematic.pdf

https://www.silabs.com/documents/public/data-sheets/Si7021-A20.pdf

Sonoff TH Sensor Si7021 is designed for convenient replacement sold as an official option for Sonoff TH10 and Sonoff TH16

https://www.itead.cc/sonoff-th.html

https://www.itead.cc/wiki/Sonoff_TH_10/16

https://tasmota.github.io/docs/devices/Sonoff-TH/

Sensors for Sonoff TH series comes with a standard 2.5mm jack (Stereo + Mic Audio Connector) which has been repurposed:

Pin	Name	Description
1	VCC	Power supply 2.2~3.6VDC
2	GND	GND
3	NC	NC
4	DATA	Single bus, data port

https://www.itead.cc/wiki/File:Si7021_audio_connector.jpg

[REQUEST] Support for more popular environmental sensors in firmware for CC2530 based Sonoff BASICZBR3?

@kirovilya Any chance you be willing to add support for any more popular environmental sensors?

I guess that the most popular in demand in this specific case would be the sensors that ITead already sell for Sonoff TH10 / Sonoff TH16 so can buy them and Sonoff BASICZBR3 from same site.

• https://www.itead.cc/sonoff-th.html

ITead sells these as Sonoff branded sensors:

• Sonoff TH Sensor Si7021
  • https://sonoff.tech/product/accessories/si7021
• Sonoff TH Sensor AM2301
  • https://sonoff.tech/product/accessories/AM2301
• Sonoff Temp Sensor DS18B20
  • https://sonoff.tech/product/accessories/DS18B20

They sell this "SONOFF 5M Sensor Extension Cable" would could be cut of and made into an adapter:

• https://sonoff.tech/product/accessories/al560-sensor-extention-cable

Other popular low-cost sensors that support both humidity + temperature are DHT11, DHT12 & DHT22

• https://www.itead.cc/humidity-temperature-sensor-dht11.html
  • https://www.itead.cc/wiki/DHT11_Humidity_Temperature_Sensor_Brick
• https://www.itead.cc/humidity-temperature-sensor-dht22.html

They also sell several different versions of DS18B20

• https://www.itead.cc/waterproof-ds18b20-temperature-sensor.html
• https://www.itead.cc/temperature-sensor-with-steel-head-and-plastic-connector.html
• https://www.itead.cc/temperature-sensor-with-steel-head.html

@ptvoinfo Zigbee Configurable Firmware v2.3 for example now supports a lot of environmental sensors; DS18B20, BMP280, BME280, DHT11, DHT22, DHT12, AM2301, Sonoff SI7021, MHZ19, SenseAir S8 so not sure if he would be willing to share his code and input on it for CC2530?

• https://ptvo.info/zigbee-switch-configurable-firmware-v2-210/
  • https://ptvo.info/zigbee-switch-configurable-firmware-router-199/

[REQUEST] Zigbee firmware binaries for the CC2530 based Sonoff BASICZBR3?

Any chance that you can post binary hex file(s) that are ready to be flashed by non-developers too?

Zigbee router firmware hex for Sonoff BASICZBR3 (a.k.a. Sonoff BASIC ZBR3 / Sonoff BASIC ZB R3)?

Would be nice if also could submit to Koenkk repo:

• https://github.com/Koenkk/Z-Stack-firmware/

PS: Had to use Google Translate but read https://habr.com/ru/company/iobroker/blog/495926/

[REQUEST] Support for DHT11 (Humidity and Temperature) sensor

Request support for DHT11 (Humidity and Temperature) sensor:

https://www.itead.cc/humidity-temperature-sensor-dht11.html

https://www.itead.cc/electronic-brick-dht11-humidity-temperature-sensor-brick.html

https://www.itead.cc/wiki/DHT11_Humidity_Temperature_Sensor_Brick

DHT11 sensors are less expensive and less accurate than DHT22

Please also see the request for DHT22 support -> #8