ewasm/ewasm-explorer

[ORPHANE] Minimal account explorer for ewasm testnet.

ewasm explorer

Minimal account explorer for ewasm testnet. Fully client-side, communicates with testnet client over json-rpc. Use genesis file with ewasm contracts.

Available Scripts

In the project directory, you can run:

npm start

Runs the app in the development mode.
Open http://localhost:3000 to view it in the browser.

The page will reload if you make edits.
You will also see any lint errors in the console.

npm run build

Builds the app for production to the build folder.
It correctly bundles React in production mode and optimizes the build for the best performance.

The build is minified and the filenames include the hashes.
Your app is ready to be deployed!

npm run eject

Note: this is a one-way operation. Once you eject, you can’t go back!

If you aren’t satisfied with the build tool and configuration choices, you can eject at any time. This command will remove the single build dependency from your project.

Instead, it will copy all the configuration files and the transitive dependencies (Webpack, Babel, ESLint, etc) right into your project so you have full control over them. All of the commands except eject will still work, but they will point to the copied scripts so you can tweak them. At this point you’re on your own.

You don’t have to ever use eject. The curated feature set is suitable for small and middle deployments, and you shouldn’t feel obligated to use this feature. However we understand that this tool wouldn’t be useful if you couldn’t customize it when you are ready for it.

ewasm-explorer's Issues

Action required: Greenkeeper could not be activated 🚨

🚨 You need to enable Continuous Integration on all branches of this repository. 🚨

To enable Greenkeeper, you need to make sure that a commit status is reported on all branches. This is required by Greenkeeper because it uses your CI build statuses to figure out when to notify you about breaking changes.

Since we didn’t receive a CI status on the greenkeeper/initial branch, it’s possible that you don’t have CI set up yet. We recommend using Travis CI, but Greenkeeper will work with every other CI service as well.

If you have already set up a CI for this repository, you might need to check how it’s configured. Make sure it is set to run on all new branches. If you don’t want it to run on absolutely every branch, you can whitelist branches starting with greenkeeper/.

Once you have installed and configured CI on this repository correctly, you’ll need to re-trigger Greenkeeper’s initial pull request. To do this, please delete the greenkeeper/initial branch in this repository, and then remove and re-add this repository to the Greenkeeper App’s white list on Github. You'll find this list on your repo or organization’s settings page, under Installed GitHub Apps.

Action required: Greenkeeper could not be activated 🚨

🚨 You need to enable Continuous Integration on all branches of this repository. 🚨

To enable Greenkeeper, you need to make sure that a commit status is reported on all branches. This is required by Greenkeeper because it uses your CI build statuses to figure out when to notify you about breaking changes.

Since we didn’t receive a CI status on the greenkeeper/initial branch, it’s possible that you don’t have CI set up yet. We recommend using Travis CI, but Greenkeeper will work with every other CI service as well.

If you have already set up a CI for this repository, you might need to check how it’s configured. Make sure it is set to run on all new branches. If you don’t want it to run on absolutely every branch, you can whitelist branches starting with greenkeeper/.

Once you have installed and configured CI on this repository correctly, you’ll need to re-trigger Greenkeeper’s initial pull request. To do this, please delete the greenkeeper/initial branch in this repository, and then remove and re-add this repository to the Greenkeeper App’s white list on Github. You'll find this list on your repo or organization’s settings page, under Installed GitHub Apps.

Sprint todo

• Deploying ewasm contracts (paste in wast code and deploy it as a contract)
• When you deploy a contract, calculate new address and add to accounts list (depends on previous)
• Optimization: don't fetch any account data when it's not expanded
• When an account is expanded, and a storage key changes, highlight this in color
• Tab or toggle to switch between WAST and wasm bytecode or EVM bytecode / opcodes list
• Refactor, clean up codebase

Action required: Greenkeeper could not be activated 🚨

🚨 You need to enable Continuous Integration on all branches of this repository. 🚨

To enable Greenkeeper, you need to make sure that a commit status is reported on all branches. This is required by Greenkeeper because it uses your CI build statuses to figure out when to notify you about breaking changes.

Since we didn’t receive a CI status on the greenkeeper/initial branch, it’s possible that you don’t have CI set up yet. We recommend using Travis CI, but Greenkeeper will work with every other CI service as well.

If you have already set up a CI for this repository, you might need to check how it’s configured. Make sure it is set to run on all new branches. If you don’t want it to run on absolutely every branch, you can whitelist branches starting with greenkeeper/.

Once you have installed and configured CI on this repository correctly, you’ll need to re-trigger Greenkeeper’s initial pull request. To do this, please delete the greenkeeper/initial branch in this repository, and then remove and re-add this repository to the Greenkeeper App’s white list on Github. You'll find this list on your repo or organization’s settings page, under Installed GitHub Apps.

Action required: Greenkeeper could not be activated 🚨

🚨 You need to enable Continuous Integration on all branches of this repository. 🚨

To enable Greenkeeper, you need to make sure that a commit status is reported on all branches. This is required by Greenkeeper because it uses your CI build statuses to figure out when to notify you about breaking changes.

Since we didn’t receive a CI status on the greenkeeper/initial branch, it’s possible that you don’t have CI set up yet. We recommend using Travis CI, but Greenkeeper will work with every other CI service as well.

If you have already set up a CI for this repository, you might need to check how it’s configured. Make sure it is set to run on all new branches. If you don’t want it to run on absolutely every branch, you can whitelist branches starting with greenkeeper/.

Once you have installed and configured CI on this repository correctly, you’ll need to re-trigger Greenkeeper’s initial pull request. To do this, please delete the greenkeeper/initial branch in this repository, and then remove and re-add this repository to the Greenkeeper App’s white list on Github. You'll find this list on your repo or organization’s settings page, under Installed GitHub Apps.

Action required: Greenkeeper could not be activated 🚨

🚨 You need to enable Continuous Integration on all branches of this repository. 🚨

To enable Greenkeeper, you need to make sure that a commit status is reported on all branches. This is required by Greenkeeper because it uses your CI build statuses to figure out when to notify you about breaking changes.

Since we didn’t receive a CI status on the greenkeeper/initial branch, it’s possible that you don’t have CI set up yet. We recommend using Travis CI, but Greenkeeper will work with every other CI service as well.

If you have already set up a CI for this repository, you might need to check how it’s configured. Make sure it is set to run on all new branches. If you don’t want it to run on absolutely every branch, you can whitelist branches starting with greenkeeper/.

Once you have installed and configured CI on this repository correctly, you’ll need to re-trigger Greenkeeper’s initial pull request. To do this, please delete the greenkeeper/initial branch in this repository, and then remove and re-add this repository to the Greenkeeper App’s white list on Github. You'll find this list on your repo or organization’s settings page, under Installed GitHub Apps.