hi35xx/hi35xx-buildroot

buildroot for hisilicon hi35xx series

hi35xx-buildroot's Issues

hi3796 support

glinuz/hi3798mv100#11

any help?

Can I get RTSP destination URL ?

Hello colleagues !

I have one question..

Can I get RTSP destination URL from live-streamer started on HI3518EV1 cam with ov9712 sensor ?

Thank you !

Building a bootloader for hi3520dv200

Good afternoon
Has anyone tried building a bootloader for the hi3520dv200 processor ?
I have it build correctly, but it doesn't work. On the monitor screen, only spaces run at start. Something can't initialize. If I build the loader using the original toolchain, then everything is fine. Does anyone else have such a problem or can check ? Thanks.

Could you help me with phy lan8710a?

Hi,
Could you help me with phy SMSC lan8710a (http://ww1.microchip.com/downloads/en/DeviceDoc/00002164B.pdf)? It can't transmit packets. Device only receives packets.

Thanks.

How upload image if network not work.

Hello,

I have an IPG-53H13PE-WP module that only works with wifi, but when I turn on the board, wifi is not activated.

How can I upload the firmware if I can not connect via network?

When turn on I can see in Putty (Serial Port 115200):

U-Boot 2010.06-svn (Oct 14 2015 - 15:07:23)

DRAM: 256 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
Spi(cs1): Block:64KB Chip:8MB Name:"MX25L6406E"
envcrc 0xb599d235
ENV_SIZE = 0xfffc
In: serial
Out: serial
Err: serial
Press Ctrl+C to stop autoboot
CFG_BOOT_ADDR:0x58040000
8192 KiB hi_sfc at 0:0 is now current device

boot load complete: 2068024 bytes loaded to 0x82000000
SAVE TO 80008000 !
Booting kernel from Legacy Image at 82000000 ...
Image Name: linux
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2067960 Bytes = 2 MiB
Load Address: 80008000
Entry Point: 80008000

load=0x80008000,_bss_end=80829828,image_end=80200df8,boot_sp=807c7168
Loading Kernel Image ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

And don't load.

PRINTENV

U-Boot 2010.06-svn (Oct 14 2015 - 15:07:23)

DRAM: 256 MiB
Check spi flash controller v350... Found
Spi(cs1) ID: 0xC2 0x20 0x17 0xC2 0x20 0x17
Spi(cs1): Block:64KB Chip:8MB Name:"MX25L6406E"
envcrc 0xb599d235
ENV_SIZE = 0xfffc
In: serial
Out: serial
Err: serial
Press Ctrl+C to stop autoboot
hisilicon # printenv
bootcmd=setenv setargs setenv bootargs ${bootargs};run setargs;fload;bootm 0x82000000
bootdelay=1
baudrate=115200
bootfile="uImage"
da=mw.b 0x82000000 ff 1000000;tftp 0x82000000 u-boot.bin.img;sf probe 0;flwrite
du=mw.b 0x82000000 ff 1000000;tftp 0x82000000 user-x.cramfs.img;sf probe 0;flwrite
dr=mw.b 0x82000000 ff 1000000;tftp 0x82000000 romfs-x.cramfs.img;sf probe 0;flwrite
dw=mw.b 0x82000000 ff 1000000;tftp 0x82000000 web-x.cramfs.img;sf probe 0;flwrite
dc=mw.b 0x82000000 ff 1000000;tftp 0x82000000 custom-x.cramfs.img;sf probe 0;flwrite
up=mw.b 0x82000000 ff 1000000;tftp 0x82000000 update.img;sf probe 0;flwrite
ua=mw.b 0x82000000 ff 1000000;tftp 0x82000000 upall_verify.img;sf probe 0;flwrite
tk=mw.b 0x82000000 ff 1000000;tftp 0x82000000 uImage; bootm 0x82000000
dd=mw.b 0x82000000 ff 1000000;tftp 0x82000000 mtd-x.jffs2.img;sf probe 0;flwrite
ipaddr=192.168.1.10
serverip=192.168.1.107
netmask=255.255.255.0
bootargs=mem=${osmem} console=ttyAMA0,115200 root=/dev/mtdblock1 rootfstype=cramfs mtdparts=hi_sfc:256K(boot),3520K(romfs),2560K(user),1280K(web),256K(custom),320K(mtd)
ethaddr=00:12:15:4b:be:13
HWID=8043420004048425
NID=0x0100
muxctl0=0x200f00dc
muxval0=1
gpio0=0x95
gpioval0=0
osmem=40M
appSystemLanguage=SimpChinese
appVideoStandard=PAL
stdin=serial
stdout=serial
stderr=serial
verify=n
ver=U-Boot 2010.06-svn (Oct 14 2015 - 15:07:23)

Environment size: 1359/65532 bytes

Wrong path while himpp-hi3518v100 1.0.A.0 Downloading

himpp-hi3518v100 1.0.A.0 Downloading
'/home/parallels/Devel/hi35xx-buildroot/package/himpp/himpp-hi3518v100/hi3518v100-mpp2-1.0.A.0.tgz' -> '/home/parallels/Devel/hi35xx-buildroot/output/build/.hi3518v100-mpp2-1.0.A.0.tgz.jFNw7s/output'
WARNING: no hash file for hi3518v100-mpp2-1.0.A.0.tgz
himpp-hi3518v100 1.0.A.0 Extracting
mkdir -p /home/parallels/Devel/hi35xx-buildroot/output/build/himpp-hi3518v100-1.0.A.0
tar -zxf /home/parallels/Devel/hi35xx-buildroot/dl/hi3518v100-mpp2-1.0.A.0.tgz --strip-components=2 -C /home/parallels/Devel/hi35xx-buildroot/output/build/himpp-hi3518v100-1.0.A.0
tar (child): /home/parallels/Devel/hi35xx-buildroot/dl/hi3518v100-mpp2-1.0.A.0.tgz: Cannot open: No such file or directory

./dl/hi3518v100-mpp2-1.0.A.0.tgz actually locates at ./dl/himpp-hi3518v100/hi3518v100-mpp2-1.0.A.0.tgz
I'm new to buildroot, so I just copied it to desired location

make ERROR: recipe for target 's-attrtab' failed

I'm a newer to buildroot, I used

cp configs/hi3518v200_defconfig .config
make menuconfig
make

And I get a make error,

/gcc -I../../gcc/c -I../../gcc/../include -I../../gcc/../libcpp/include -I/home/miao/Desktop/hi35xx-buildroot/output/host/usr/include -I/home/miao/Desktop/hi35xx-buildroot/output/host/usr/include -I/home/miao/Desktop/hi35xx-buildroot/output/host/usr/include  -I../../gcc/../libdecnumber -I../../gcc/../libdecnumber/dpd -I../libdecnumber -I../../gcc/../libbacktrace -I/home/miao/Desktop/hi35xx-buildroot/output/host/usr/include  -o c/c-typeck.o -MT c/c-typeck.o -MMD -MP -MF c/.deps/c-typeck.TPo ../../gcc/c/c-typeck.c
Makefile:2201: recipe for target 's-attrtab' failed
make[3]: *** [s-attrtab] 已杀死
make[3]: *** 正在等待未完成的任务....
Makefile:4113: recipe for target 'all-gcc' failed
make[2]: *** [all-gcc] Error 2
package/pkg-generic.mk:216: recipe for target '/home/miao/Desktop/hi35xx-buildroot/output/build/host-gcc-initial-6.2.0/.stamp_built' failed
make[1]: *** [/home/miao/Desktop/hi35xx-buildroot/output/build/host-gcc-initial-6.2.0/.stamp_built] Error 2
Makefile:76: recipe for target '_all' failed
make: *** [_all] Error 2

maybe this is an error about make gcc. I should use a external toolchain?

Thanks.

Any direct support for 3519?

Hi, I noticed that there is NO 3519 folder under board/hisilicon/, but 3518 and 3520 are down there. I just wonder if you've got the direct support to 3519?

Cheers

qt5base 编译出错 global.h:86:30: error: division by zero in

在编译hi3518ev200之后，编译qt5base出现错误
`
Prior to reconfiguration, make sure you remove any leftovers from
the previous build.

In file included from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/qglobal.h:1:0,
from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/../../src/corelib/text/qchar.h:43,
from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/qchar.h:1,
from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/../../src/corelib/text/qstring.h:49,
from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/qstring.h:1,
from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/../../src/corelib/io/qdir.h:43,
from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/qdir.h:1,
from /home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/src/corelib/global/qlibraryinfo.cpp:41:
/home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/include/QtCore/../../src/corelib/global/qglobal.h:86:30: error: division by zero in #if
#define QT_CONFIG(feature) (1/QT_FEATURE_##feature == 1)
^
/home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/src/corelib/global/qlibraryinfo.cpp:676:7: note: in expansion of macro 'QT_CONFIG'
#elif QT_CONFIG(relocatable)
^
make[3]: *** [qlibraryinfo_final.o] Error 1
make[2]: *** [/home/test/work/hisi3518ev200/hi35xx-buildroot-master/output/build/qt5base-5.14.2/qmake/qmake] Error 2
make[1]: *** [sub-qmake-qmake-aux-pro-make_first] Error 2
make[1]: *** Waiting for unfinished jobs....
`

uboot-tools 2018.07 Building conflicting types for ‘__packed’

uboot-tools 2018.07 Building

In file included from tools/env/fw_env.c:38:0:
./output/host/arm-buildroot-linux-uclibcgnueabi/sysroot/usr/include/mtd/ubi-user.h:329:3: error: conflicting types for ‘__packed’
} __packed;
^~~~~~~~
./output/host/arm-buildroot-linux-uclibcgnueabi/sysroot/usr/include/mtd/ubi-user.h:313:3: note: previous declaration of ‘__packed’ was here
} __packed;
^~~~~~~~

any suggestion?

Can I get .JPG screenshot ?

Hello colleagues !

I have one question..

Can I get in this firmware a screenshot in the form of a .JPG file ?

Thank you !

Hi3518e and ethernet not working ?

Hi,

I've got an 53H13PE board, with a Hi3518e and an aptina and I'm trying to use your buildroot on it.

However, the driver hieth seems to be a little upset with it, since it give me an interface (eth0) wich emits and receives absolutely no packet.
I can assign it an ip address, but whatever I do, no packet are sended nor received (check by tcpdump on the board, or on my network).
The on-board firmware works well on this aspect.

I've used the linux 3.0 version, since with the 3.4 I don't have any serial console (and no network).
I've tried to modify the RMII_MODE_{U,D} and the PHYID_{U,D} in the linux config, to no avail.

Have you got this problem , and/or do you have an idea where to look at to investigate ?

Do you know any "cheap" board that is compatible with this buildroot (it could be easier to just switch the board :))

Cordially

Ps : on the on-board firmware, I've got theses informations, but I don't know what to do with

From boot :

<6>PHY: himii:01 - Link is Up - 100/Full
<6>Sofia uses obsolete (PF_INET,SOCK_PACKET

from some other conf file

DRIVER=hieth
MODALIAS=platform:hiet
himii:01

from the directory /sys/devices/platform/hieth.0/net/eth0

$cat iflink 
2
$cat link_mode 
0
$cat type
1
$cat operstate 
up
$cat features 
0x4000
$cat flags 
0x1003

Driver hieth sfv200/sfv300 doesn't work on hi3518ep board

Hi,

thank you for your project. I can not setup it on hi3518ep board. Ethernet doesn't work. In U-BOOT ethernet works normally. Please help me.

Thanks.

hi3518ev200 and sensor ar0130; live-streamer

Hello, I compiled using hi3518v200_defconfig and am able to boot using the generated rootfs and kernel on a meshare camera I have. Generally everything appears to work except for I cannot get a rtsp stream going.

dmesg_latest.log

/proc/umap/vb and /proc/umap/h264e not showing any streams..