jildertviet/tiycs

This Is Your Captain Speaking

tiycs's Issues

Pull up @ IO23 turns buck IC off during boot

Memory limit @ videos

Can't load all three at the same time.
Try dynamic loading.

Mountingplate

Silkscreen button functions

Add fuse

12V and +12V are not connected @ main board

Min floor @ pow(value, 2)

Lowest values render to 0.
0 should be 0
1 should be 1-ish.

send hello world message @ boot

Option to add tex-mapping via OSC

Issues with latomic

openframeworks/openFrameworks#6427

Mounting the BMS is difficult

OTA with server

For quicker updates

DC connector shorts something?

Measure 3V @ 12V when connected...

Jonisks too bright vs. resolution?

Think about accesibility of ports and buttons

Panelize ledPanel for production

Max quantity is 50 pieces.
25 * 5 = 125
(25 * 5) / 4 = 31.25
So 30 4-panel boards will result in 24 combined pieces (5 ledPanels per piece)

Max panelized size = 250x250mm

Find components that are in stock (change footprint!)

White LED, used: C2827271
Current stock is 96
RGB LED, used: C784540
Current stock is: 2668

Batch of 10

10 * 5 = 50 panels.
15x panelized (4): 60 panels.
16 white leds per panel
60 * 16 = 960 white leds
60 * 36 = 2160 rgb leds

Batch of 25

Needed for a batch of 25:
25 * 5 = 125 panels (panelized, so: 30 * 4 = 120, too little. Next order quantity is 50)
16 white leds er panel
125 * 16 = 2000 white leds
36 RGB leds per panel
125 * 36 = 4500 rgb leds

Read battery voltage from sender-ESP

In SC.

3.3V regulator too weak

Rated for 250mA.
ESP32 WROOM U32 states peak @ 380 mA.
Consider SPX3819 (16V in, 3.3V out, 500mA)

Probably mistaken while designing for ESP32-S2

SC: Keep fixed number of windows on static positions

SuperCollider / GUI-situation

Wrong footprint for 1uF cap in 3.3V regulator circuit

Replace with C335102?

Silkscreen battery PCB: polarity on screw-terminal

"Alive" pings are broadcasted, so 'idle' gets unstable

A Jonisk starts broadcasting pings when it hasn't received msgs for x seconds.
But when one does, another receives this, and thinks it isn't idle.

To do: ignore this type of message when determening if idle or not.

Angles of led-panels are too wide

Oops

Option for decoupling capacitor @ battery pcb

Stars-scene should be one view

How to do it?
Set star position from SC as [(w*3), h] dimensions?
Also git each star an offset.

If out of sight: respawn @ direction-plane...

If direction is forwards, spawn at horizon.
If direction is 45deg to the left, rotate the spawn-plane?

Voltage divider on battery PCB is wrong

Is now set @ 5.1V

BMS only turns on with a power switch

Assembling LED-panels without castellated holes is a pain

White LEDs are reversed

Move switch on PCB to pre-booster IC

I thought this would be usefull, so the battery can be turned off (the 18650 cells).

However, this can't be done when its built in.
So what's the benefit?

12V line under antenna connection

MCP1703T needed min 15 pcs, reason for higher cost

Check all components ;)

peer list full @ 20

To do: improve star flight

• Joystick
• More objects

Hole for antenna too small

Test (not-live) functions are not working with IDs higher than 0

R G B resistor values are 1/3

Measured current is 6.6 mA / led for Red.
This is a 3rd of the estimated 20mA.

Calculate for max 10mA (1/2 of official max).

Add resistor to battery sense circuit

Loading a too large font renders a white screen

BMS charging // balanced

BMS turns off when one cell is 2.9V
Other 3 are 3.4V

Test voltage after charging the pack.
All 4.2? If so, then it's just a lower capacitance cell?

Battery report ends up @ wrong place.

Seems like msg buffer isn't cleared after receiving a msg?

d[ 140, 75, 20, 43, 185, 181, 8, 0, 0, 101, 110, 100 ] msga140:75:20:43:185:180:3272en MSG: a36:111:40:216:144:204:3317a36:111:40:219:21:16:3294a140:75:20:43:185:180:3272 [ 36, 111, 40, 216, 144, 205 ] 39 d[ 88, 191, 37, 248, 112, 89, 8, 0, 0, 101, 110, 100 ] msga88:191:37:248:112:88:3260en MSG: a36:111:40:216:144:204:3317a36:111:40:219:21:16:3294a140:75:20:43:185:180:3272a88:191:37:248:112:88:3260 [ 36, 111, 40, 216, 144, 205 ] 38 d[ 52, 148, 84, 20, 255, 89, 8, 0, 0, 101, 110, 100 ] msga52:148:84:20:255:88:3910en MSG: a36:111:40:216:144:204:3317a36:111:40:219:21:16:3294a140:75:20:43:185:180:3272a88:191:37:248:112:88:3260a52:148:84:20:255:88:3910 [ 36, 111, 40, 216, 144, 205 ] 86

save battery states and last seen messages

Flicker @ PWM

3.3 PSU or 9000 Hz?

Mosfet footprint too big

Gray on screens is hard to see

Increase brightness / contrast settings per image

Set envelope characteristics for all jonisks

Slider.new().action_({|v| jonisks.do{|j| j.synth.set(\attack, v.value)}});

Voltage regulator is too weak

So burns when 16.8V is applied for charging

Jonisk is AP, so can't send w/ ESPNOW

Or is it something else?

When no ID is assigned should default to 0