Didn't work with ESP32 C3 version

[juerd]

Didn't work with ESP32 C3 version

[DTTerastar]

I just got a C3 to try it on myself.

[Sys64736]

Worked good on my esp32 C3. Using devkitc-02
I haven't tried the advanced or OTA eg yet.

ESP-ROM:esp32c3-api1-20210207
Build:Feb 7 2021
rst:0xc (RTC_SW_CPU_RST),boot:0xc (SPI_FAST_FLASH_BOOT)
Saved PC:0x40381cc4
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fcd6100,len:0x1430
load:0x403ce000,len:0x930
load:0x403d0000,len:0x2d68
SHA-256 comparison failed:
Calculated: a42fd66d3efcfe06041f22310384e34152b441ee2a556807ecf4bb04bd2bf039
Expected: 4c5ab38f8781ab61391d70bf9c7e3acc52c2fa2977802cef9ae40657a00dda4b
Attempting to boot anyway...
entry 0x403ce000
I (53) boot: ESP-IDF v4.4-dev-3235-g3e370c4296 2nd stage bootloader
I (53) boot: compile time 12:14:25
I (54) boot: chip revision: 3
I (54) boot_comm: chip revision: 3, min. bootloader chip revision: 0
I (60) boot.esp32c3: SPI Speed : 80MHz
I (64) boot.esp32c3: SPI Mode : DIO
I (68) boot.esp32c3: SPI Flash Size : 4MB
I (71) boot: Enabling RNG early entropy source...
I (76) boot: Partition Table:
I (78) boot: ## Label Usage Type ST Offset Length
I (85) boot: 0 nvs WiFi data 01 02 00009000 00005000
I (91) boot: 1 otadata OTA data 01 00 0000e000 00002000
I (98) boot: 2 app0 OTA app 00 10 00010000 00300000
I (104) boot: 3 spiffs Unknown data 01 82 00310000 000f0000
I (111) boot: End of partition table
I (114) boot_comm: chip revision: 3, min. application chip revision: 0
I (120) esp_image: segment 0: paddr=00010020 vaddr=3c0a0020 size=16958h ( 92504) map
I (143) esp_image: segment 1: paddr=00026980 vaddr=3fc8e200 size=032a8h ( 12968) load
I (145) esp_image: segment 2: paddr=00029c30 vaddr=40380000 size=063e8h ( 25576) load
I (151) esp_image: segment 3: paddr=00030020 vaddr=42000020 size=9e24ch (647756) map
I (255) esp_image: segment 4: paddr=000ce274 vaddr=403863e8 size=07c60h ( 31840) load
I (261) esp_image: segment 5: paddr=000d5edc vaddr=50000000 size=00010h ( 16) load
I (266) boot: Loaded app from partition at offset 0x10000
I (266) boot: Disabling RNG early entropy source...
Connecting to WiFi SSID NOTYOURS....................................................................................................................................................................................................................................................................................................... failed.
Starting access point for configuration portal.
SSID: 'esp32-2049af'
192.168.4.1
[ 51158][E][WebServer.cpp:635] _handleRequest(): request handler not found
[ 52657][E][WebServer.cpp:635] _handleRequest(): request handler not found
[ 52800][E][WebServer.cpp:635] _handleRequest(): request handler not found
21 WiFi networks found.
[ 58999][E][WebServer.cpp:635] _handleRequest(): request handler not found
21 WiFi networks found.
[ 70825][E][WebServer.cpp:635] _handleRequest(): request handler not found
19 WiFi networks found.

I purposely put in the wrong pass for the chosen SSID for that test.

[Skywalkerf34]

@Sys64736

Compliation was working fine for me too, the thing is I didn't find the device I setUp on air with sniffer.....did you have this "on air" ? then I will check again.
As I am using original example, something maybe wrong in my environment /setup then

[Sys64736]

No, it's not. I thought it was connected, as it states in the serial but I was actually seeing my other C3 listed in the router. Debug states an IP of 255.255.255.255 so somethings off.
I'm going to look at it a little closer tomorrow and see if I can figure it out.

[Sys64736]

@Skywalkerf34
It's working for me now and getting a valid IP.

Comment out the line below in WiFiSettings.cpp
Line:469 WiFi.config(INADDR_NONE, INADDR_NONE, INADDR_NONE); // arduino-esp32 #2537

That line disables the DHCP on the router from handing out an IP. I think it was an issue from a while ago in regards to hostnames and router leases with multiple ESP32's connected. Hoping it's fixed now with the latest IDF

[Skywalkerf34]

OK, so This was exactly what I get myself....everything seem running on debug (serial) but nothing "on air"

[Skywalkerf34]

@Sys64736
Thanks Marc,
I will try your patch soon and let you know what results on my side

[Sys64736]

Ok Francis, sounds good.

[Skywalkerf34]

@Sys64736

I comment the line 469 as you suggest then
I try both basic and OTA example with same result :
compile good with no warning, serial give SSID but still cannot find this "on air"

[Sys64736]

I don't know why you can't see the access point. Did you try another phone or computer with a WiFi radio. It does show up "on air" but sometimes you have to wait for a network list to update from a scan... usually 20-30 seconds but depends on the device.

[Skywalkerf34]

@Sys64736
Yes I check on my computer and on my phone with Swiffer scanner....same ????
I will try later same code with a "real" ESP32 to compare
thanks for your kind help

[Skywalkerf34]

@Sys64736
Happy new year !
I try with an ESP32WROOM with basic example and it works great!
Witch mean that this is ESPC3 issue
is it because single core ???