esphome扩展组件
请参考esphome文档。
#引用组件库示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ example ]esp8266 通过http流播放wav
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ audio_player ]
media_player:
- platform: audio_player
name: "Media Player"
volume: 100% #可选，基准音量
buffer_size: 10240 #可选，http流缓冲区大小
i2sNoDAC: {} # 二选一，RX直接输出音频
i2s: # 二选一，外置DAC输出
bclk: GPIO15
wclk: GPIO3
dout: GPIO2cc1101 315/433mHz射频收发
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ rf_bridge_cc1101 ]
rf_bridge_cc1101:
spi_id: cc1101 #与cc1101连接的spi总线id
cs_pin: GPIO5 #cc1101的片选pin
pin: GPIO14 #cc1101的GD0连接在esp上的pin
frequency: 433.92 #指定收发频率
tolerance: 80% #容许信号时长误差
filter: 100us #忽略小于这个时长的信号
idle: 4ms #信号超时时间
buffer_size: 2kb #信号缓存大小
dump: #可选，未匹配到相关sensor或者没有配置on_code_received时，在控制台打印接收到的内容
- rc_switch
on_code_received: #示例，收到内容时打印
then:
- lambda: |-
ESP_LOGD("Trigger","received code %06X", x.code);
binary_sensor:
- platform: rf_bridge_cc1101 #示例，接收到指定内容时触发一个传感器
name: "Motion Sensor"
device_class: "motion"
filters:
- delayed_off: 500ms
code: "101010111110010010101010" #dump中打印的值
protocol: 1小米电动牙刷T500
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ xiaomi_m1st500 ]
esp32_ble_tracker:
sensor:
- platform: xiaomi_m1st500
mac_address: "XX:XX:XX:XX:XX:XX" #你的牙刷mac地址
score:
name: "Toothbrush Score" #刷牙分数，在一次完整的2分钟刷牙后得出
battery_level:
name: "Toothbrush Battery Level" #电池电量小米烟雾报警器蓝牙版mcn02
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ xiaomi_smoke_detector ]
esp32_ble_tracker:
sensor:
- platform: xiaomi_smoke_detector
mac_address: "XX:XX:XX:XX:XX:XX" #烟雾报警器蓝牙mac地址
bindkey: "0000000000000000000000000000000" #token
alert: # 可选：报警 binary sensor
name: "Smoke Detector Alert"
status: # 可选：报警器状态 sensor
name: "Smoke Detector Status"
status_text: # 可选：报警器文本状态 text sensor
name: "Smoke Detector Status Text"
filters: # 可选：翻译文本状态
- map:
- normal -> 正常监测
- alert -> 火灾报警
- fault -> 设备故障
- self-check -> 设备自检
- analog alert -> 模拟报警
- unkown -> 未知状态
battery_level: # 可选：报警器电量 sensor
name: "Smoke Detector Battery"支持型号为ssw-tds-2u的一款基于urat协议的2路带水温tds检测仪。可输出双路tds及一路水温。
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ ssw_tds ]
uart:
id: uart_tds
baud_rate: 9600
rx_pin: RX #你的RX引脚
tx_pin: TX #你的TX引脚
sensor:
- platform: ssw_tds
source_tds:
name: "Source TDS" #自来水TDS
clean_tds:
name: "Clean TDS" #净水TDS
temperature:
name: "Water Temperature" #水温
update_interval: 5s # 可选，更新间隔默认5s支持某国产芯片的毫米波雷达，同样适用于LD1115H。只需要连接VCC,GND,TX(CEM5855H)->RX(MCU)。阈值配置参考Number
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ cem5855h ]
logger:
level: VERBOSE #如果需要在日志中查看串口信息，设置日志级别为VERBOSE
uart:
id: uart_cem5855h
baud_rate: 115200
rx_pin: RX #你的RX引脚
binary_sensor:
- platform: cem5855h
moving: #（可选）有人移动传感器
- name: mov
filters:
- delayed_off: 3s
threshold: 250 #示例：阈值可以是数字
- name: mov2 # 示例：可以配置多个不同阈值的传感器
filters:
- delayed_off: 3s
threshold: 350
occupancy: #（可选）有人静止传感器
name: occ
filters:
- delayed_off: 3s
threshold: #示例： 阈值可以是数字组件
name: "occ"
value: 250 #阈值
min_value: 10 #可调节的最小阈值
max_value: 3000 #可调节的最大阈值
step: 10 #单步调节量
motion: #（可选）人在传感器
name: motion
filters:
- delayed_off: 3s #设置一个合适的状态持续时间
threshold:
moving: 250
occupancy: 250通过经典蓝牙扫描发现蓝牙设备，蓝牙设备须处于可被发现状态
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ esp32_bt_tracker, bt_presence, bt_rssi ]
esp32_bt_tracker: #启用经典蓝牙扫描组件，控制台会以debug消息打印扫描到的未设置sensor的设备mac
scan_parameters:
duration: 5s #每次扫描持续时间，影响不大
binary_sensor: #示例，扫描到设备
- platform: bt_presence
mac_address: XX:XX:XX:XX:XX:XX #安卓手机蓝牙mac地址
name: "android"
sensor: #示例，显示设备信号强度
- platform: bt_rssi
mac_address: XX:XX:XX:XX:XX:XX #安卓手机蓝牙mac地址
name: "android"支持海凌科fpm383c电容式指纹模块
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ fpm383c ]
esphome:
on_boot: # 可选，上电重置指纹模块
priority: 250
then:
- fpm383c.reset
uart: #指定串口
id: uart_fpm383c
baud_rate: 57600
rx_pin: GPIO26
tx_pin: GPIO25
fpm383c:
auto_learning: True # 默认根据匹配结果自动更新指纹
on_reset: # 可选，指纹模块完成初始化
- light.turn_on: #示例，打开蓝灯
id: fpm383c_id
brightness: 50%
red: 0
green: 0
blue: 100%
on_touch: #手指触摸模块时触发
- light.turn_on: #示例，打开黄灯
id: fpm383c_id
brightness: 50%
red: 100%
green: 100%
blue: 0
on_release: #手指松开时触发
- light.turn_on: #示例，打开蓝灯
id: fpm383c_id
brightness: 50%
red: 0
green: 0
blue: 100%
on_finger_scan_unmatched: #指纹匹配失败时触发
- light.turn_on: #示例，打开红灯
id: fpm383c_id
brightness: 50%
red: 100%
green: 0
blue: 0
on_finger_scan_matched: #指纹匹配成功时触发
- light.turn_on: #示例，打开绿灯
id: fpm383c_id
brightness: 50%
red: 0
green: 100%
blue: 0
on_finger_register_progress: #指纹注册进度，可以获取当前指纹编号和注册进度
then:
- lambda: |-
ESP_LOGD("PROGRESS", "id: %04X, progress: %d%%", x.id, x.progress_in_percent); // 示例，打印进度日志
light:
- platform: fpm383c #配置RGB指示灯，所有颜色都会被重新映射到6种颜色（白色映射到红色）
name: "指示灯"
id: fpm383c_id
effects: # 仅支持以下效果
- breathing: # 呼吸灯
name: "Breathing" # 效果默认名称
min_brightness: 0% # 最小亮度
max_brightness: 100% # 最大亮度
rate: 50% # 每秒变化百分比
- flashing: # 闪烁
name: "Flashing" # 效果默认名称
on_length: 200ms # 亮灯时间（10ms倍数时间）
off_length: 100ms # 灭灯时间（10ms倍数时间）
count: 3 # 闪烁次数
# 灯光效果示例
button:
- platform: template
name: "breathing"
on_press:
- light.turn_on: # 打开蓝色呼吸灯
id: fpm383c_id
red: 0
green: 0
blue: 100%
effect: Breathing可用动作
- fpm383c.register 注册新指纹
- fpm383c.clear 删除已注册指纹
- fpm383c.cancel 取消指纹匹配或注册
- fpm383c.reset 重启指纹模块
支持符合DL/T 645-2007规范的电表
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ dlt645 ]
remote_transmitter:
pin: GPIO4
carrier_duty_percent: 50%
remote_receiver:
pin: GPIO5
dlt645:
address: 123456789012 #可选，12位电表地址，一般印刷于电表上。不配置可自动获取。
power:
name: "Power" #瞬时总有功功率
update_interval: 10s #更新间隔
power_a:
name: "Power A" #瞬时A相有功功率
update_interval: 10s #更新间隔
power_b:
name: "Power B" #瞬时B相有功功率
update_interval: 10s #更新间隔
power_c:
name: "Power C" #瞬时C相有功功率
update_interval: 10s #更新间隔
energy:
name: "Energy" #当前组合有功总电能
update_interval: 30s #更新间隔
energy_a:
name: "Energy A" #当前A相正向有功电能
update_interval: 30s #更新间隔
energy_b:
name: "Energy B" #当前B相正向有功电能
update_interval: 30s #更新间隔
energy_c:
name: "Energy C" #当前C相正向有功电能
update_interval: 30s #更新间隔tcp转发串口
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ telnet ]
uart:
rx_pin: RX
tx_pin: TX
baud_rate: 115200
rx_buffer_size: 1kB
telnet:
port: 23支持平头熊无线蓝牙开关（型号：PTX_YK1_QMIMB）
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ ptx_yk1 ]
esp32_ble_tracker:
scan_parameters:
interval: 300ms
window: 300ms
active: false
on_ble_advertise: # 调试用途，按下无线按钮可查找蓝牙开关MAC地址
then:
- lambda: |-
for (auto data : x.get_manufacturer_datas()) {
if (data.uuid == esp32_ble_tracker::ESPBTUUID::from_uint16(0x5348)) {
ESP_LOGD("ptx_yk1", "Found ptx_yk1_qmimb: %s", x.address_str().c_str());
return;
}
}
binary_sensor:
- platform: ptx_yk1
mac_address: "XX:XX:XX:XX:XX:XX" # 蓝牙开关MAC地址，可使用上面的调试代码查找新开关的MAC地址
name: "BLE Button"
timeout: 300ms # 可选，蓝牙BLE信号接收的超时时间。取决于信号环境和esp32_ble_tracker的scan_parameters配置。如果时间设置过短，可能会导致长按误判为短按；而时间设置过长则会延迟蓝牙开关的松开判定。
on_multi_click: # 单击、双击、长按示例配置
- timing:
- ON for at most 2s # 短按须少于2秒
- OFF for at least 1s # 1秒内无按下动作，判定为单击
then:
- logger.log: "Clicked" # 配置单击动作
- timing:
- ON for at most 2s # 第一次短按须少于2秒
- OFF for 0s to 1s # 两次短按须间隔1秒以内
- ON for at most 2s # 第二次短按须少于2秒
- OFF for at least 0s
then:
- logger.log: "Double-Clicked" # 配置双击动作
- timing:
- ON for at least 2s # 长按须大于2秒
then:
- logger.log: "Long-Pressed" # 配置长按动作注意：这款蓝牙开关可能无法识别快速双击。
支持小米通用遥控协议
配置示例
external_components:
- source: github://ryanh7/esphome-custom-components
components: [ xiaomi_remote ]
esp32_ble_tracker:
scan_parameters:
interval: 300ms
window: 300ms
active: false
xiaomi_remote:
mac_address: XX:XX:XX:XX:XX:XX
bindkey: "0000000000000000000000000000000" #token，可选，不配置为不加密
press: #按下动作传感器，可配置一到多个，示例为一个
name: Button Binary
button: 0 # 可选，配置按钮编号（0-9），默认任意按钮
action: #按键动作传感器（0:无动作 1:单击 2：双击 3：三击 99：长按），可配置一到多个，示例为多个
- name: Button 0 Action
button: 0 # 可选，配置按钮编号（0-9），默认任意按钮
- name: Button 1 Action
button: 1
action_text: #按键动作文本传感器（Idle:无动作 Click:单击 Double-click：双击 Triple-click：三击 Long press：长按），可配置一到多个，示例为多个
name: Button Text
button: 0 # 可选，配置按钮编号（0-9），默认任意按钮
battery_level: # 电池电量
name: Button Battery
on_click: # 单击示例
- button: 0
then:
- logger.log: "单击0"
- button: 1
then:
- logger.log: "单击1"
on_double_click: # 双击示例
then:
- logger.log: "双击"
on_triple_click: # 三击示例
then:
- logger.log: "三击"
on_long_press: # 长按示例
then:
- logger.log: "长按"
React
Typescript
Django
Laravel
Facebook
Microsoft
Google
Alibaba
D3
Tencent