mahtaran/dotfiles

Mahtaran's dotfiles

Git configuration

If you wish to diff the secret files, you need to set up SOPS as a diff tool.

# Make sure you have sops installed
$ git config diff.sopsdiffer.textconv "sops decrypt"

Installation guide

1. Reset Secure Boot status to 'set up' mode in your UEFI firmware settings.

2. Boot from a NixOS installation media.

3. Close the graphical installer and open a terminal.

4. Run lsblk and note the name of the disk you'd like to use. For me, it was nvme1n1.

5. Ensure you have a working internet connection.

6. Run sudo nix run --experimental-features "nix-command flakes" github:nix-community/disko#disko-install -- --flake github:mahtaran/dotfiles#feanor --write-efi-boot-entries --disk primary /dev/nvme1n1

   1. Enter the password for the disk encryption when prompted.

7. Reboot into the new installation, enter your chosen disk encryption password and log into the account mahtaran with the password password.

8. Ensure you have a working internet connection again.

9. Git clone this repository.

10. Import your personal SSH keypair and convert it to an age key:

    # I store my ssh keys in Bitwarden, so I use the Bitwarden CLI to get them
    # Adjust as needed
    $ nix-shell -p ssh-to-age bitwarden-cli
    $ bw config server https://vault.bitwarden.eu
    $ export BW_SESSION=$(bw login --raw)
    $ bw get notes "SSH key" > ~/.ssh/id_ed25519
    $ chmod u=rw,go= ~/.ssh/id_ed25519
    $ ssh-keygen -y -f ~/.ssh/id_ed25519 > ~/.ssh/id_ed25519.pub
    $ ssh-add
    # Create the persistent age keys file, so that we don't override the symlink
    $ touch /persist/home/mahtaran/.config/sops/age/keys.txt
    # Add the host key to the age encryption keys
    $ sudo ssh-to-age -private-key -i /etc/ssh/ssh_host_ed25519_key >> ~/.config/sops/age/keys.txt
    # Make sure to add the public key in the `.sops.yaml` file!
    $ ssh-to-age -i /etc/ssh/ssh_host_ed25519_key.pub
    # Assuming you have a passphrase set for the SSH key (as you should)
    $ read -s SSH_TO_AGE_PASSPHRASE; export SSH_TO_AGE_PASSPHRASE
    $ ssh-to-age -private-key -i ~/.ssh/id_ed25519 >> ~/.config/sops/age/keys.txt

11. Ensure that sudo bootctl status reports UEFI firmware with TPM2 support, and secure boot in setup mode.

12. Run sudo sbctl create-keys.

13. Run sudo sbctl enroll-keys --microsoft.

14. Rebuild the system: sudo nixos-rebuild switch --flake ~/dotfiles.

15. Check that all went well using sudo sbctl verify (only the Linux image should not be signed).

16. Turn Secure Boot back on.

17. Run sudo systemd-cryptenroll /dev/disk/by-partlabel/disk-primary-luks --wipe-slot=tpm2 --tpm2-device=auto --tpm2-pcrs=0+2+7 to enrol the disk encryption key in the TPM.

18. We can now also clean up old systemd-boot entries: sudo rm /boot/loader -r, followed by rebuilding the system again.

Creating a secrets file

Create the hash for the password you want, and put it in a secrets file

$ read -s PASSWORD; echo $PASSWORD | mkpasswd -s
$y$j9T$rAFN5Csek3da0mv72gb4B.$M3dzM3xKHNzHNkiSh5g2K4maVPJCNr9hsVCRGa/27b8
# You will probably get something else, as this is the hash for 'password'
$ nix-shell -p sops --run "sops ~/dotfiles/secret/user/mahtaran/secrets.yaml"

# ~/dotfiles/secret/user/mahtaran/secrets.yaml
password: $y$j9T$rAFN5Csek3da0mv72gb4B.$M3dzM3xKHNzHNkiSh5g2K4maVPJCNr9hsVCRGa/27b8

Add a Windows boot entry

# Assuming /dev/nvme0n1p1 is the EFI partition of the Windows installation
$ sudo mount /dev/nvme0n1p1 /mnt
$ sudo cp /mnt/EFI/Microsoft /boot/EFI/ -r

Delete old boot entries

# Do make sure that you don't have other Linux installations with an EFI boot entry
$ nix-shell -p efibootmgr --run "sudo efibootmgr -BL 'Linux Boot Manager'"
$ sudo bootctl install
$ sudo nixos-rebuild switch --flake ~/dotfiles