makerbase-mks / mks-robin2 Goto Github PK

MKS Robin2 is a powerful 32-bit 3D printer control board with STM32F407ZET6 . the CPU 168MHZ. Support MKS Robin TFT35 Screens, use RobinTFT35 can preview model. The motherboard integrates 5 AXIS interface, hot bed, 2 heating heads, 3 NTC100K, 2 MAX31855.Support MKS Robin WIFI for cloud printing.Supports firmware update by SD card…

Home Page: https://www.aliexpress.com/item/33006653472.html?spm=2114.12010612.8148356.3.334a65f4LZBtt2

C++ 15.64% C 83.62% Makefile 0.11% Python 0.32% Shell 0.24% OpenSCAD 0.03% G-code 0.01% HTML 0.01% CSS 0.01% JavaScript 0.01%

mks-robin2's Introduction

1、According to the content that needs to be updated, copy the following file to the SD card:

 (1)、update the config file：robin2_cfg.txt
 (2)、update images：         mks_pic
 (3)、update font：           mks_font
 (4)、update Robin firmware：   Robin2.bin
 (5)、update Wifi firmware：  MksWifi.bin

2、V1.0.1 Modifications:
 (1)、Fix the bug that read Large capacity sd card data error sometimes.
 (2)、Fix bug with manual shutdown invalid.
 (3)、Fixed a problem in which the title bar displayed abnormally during printing.
 (4)、Fixed bug where external drive printing would be skewed.
 (5)、Fixed a bug where moving too fast when manually leveling.

3、V1.0.2 Modifications:
 (1)、Fix the bug that read Large capacity sd card data error sometimes.
 (2)、Fixed a bug that model offset in printingin when connected external motor driver;
 (3)、Fixed a bug that after the bltouch leveling, the power failure continued print to hang;
 
4、V1.0.3 Modifications:
 (1)、Correct the problem of double limit;
 (2)、Open pulse hold time configuration item;
 (3)、Fix the bug that the configuration file is invalid when the pause position is modified;
 (4)、Fix the material break pause and resume printing misalignment;
 (5)、Correct the problem that the extrusion head will always heat up when the SD card cannot be read during printing;
 (6)、Fixed the problem that the interface name is displayed abnormally when the file name exceeds 150 bytes;
 (7)、Fix the problem that the file name is more than 30 bytes when the power is off and continue to play abnormally;
 (8)、Correct the problem that the machine stops after the material is cut off when printing the first layer;
 (9)、Added function: when there is no printing material, a prompt box pops up before printing the file;
(10)、Corrected the problem of misalignment of printing when heating and cutting the material when executing M109 instruction;
 
 4、Hardware schematic please see the 'Hardware' folder.
 
 ## Note
- Thank you for using MKS products. If you have any questions during use, please contact us in time and we will work with you to solve it.
- For more product dynamic information and tutorial materials, you can always follow MKS's Facebook/Twitter/Discord/Reddit/Youtube and Github. Thank you!
- MKS Github: https://github.com/makerbase-mks  
- MKS Facebook: https://www.facebook.com/Makerbase.mks/  
- MKS Twitter: https://twitter.com/home?lang=en  
- MKS Discord: https://discord.gg/4uar57NEyU
- MKS Reddit: https://www.reddit.com/user/MAKERBASE-TEAM/

mks-robin2's People

Contributors

Stargazers

Watchers

Forkers

davg1 fubo365 habibzadeh irons71 mohammadfatemieh petel29 officesteve shaogp shev4uck liqijian101 1054114709 yu1741588584

mks-robin2's Issues

Firmware Compile Error

fatal error: SoftwareSerial.h: No such file or directory

просьба

Похоже MKS отказалась от поддержки данного продукта.
Скинули "левые" исходные коды, и забыли.

Homing issue and microstepping

Hello,
i'm using the robin2 with tmc2208 drivers. For z-homing i want to use an inductive Probe. Right now the problem is with X and Y homed the printhead with probe is about 10mm off the printbed, the probe won't see the printbed.

Is there a section for the config file to define the homing coordinates ?

Second question, How do i enable Microstepping ? I have noticed the Jumpers under the stepper drivers but found no information what they are supposed to do.

Any Help appreciated

G28 out of Bed

Hi
I use firmware 1.0.3, 3dtouch is a MKS, TMC2209 is MKS.

When i activate autoleveling, 3dtouch, etc, G28 is out of bed (probe with nozzle, not 3dtouch).
If i pass G29 directly with terminal, it work.
Printing with manual leveling work perfectly too.

My config file :
robin2_cfg.txt

Possible to activate Z_safe_homing ? how ?

Thx

will you release Marlin 2.1.x?

it seems that Marlin official have half done support for Mks robin2, are you working for it?

request

Hello,
Could you add the "machine setting" menu like in robin nano?

Problem Firmware Update

I have a mks robin2 v1.0 and wanted to install the latest firmware V1.0.3. Unfortunately that doesn't work, he loads the firmware, transfers the font and PIC files and then says "complete".
When I turn the board off and on again, the message booting comes up and nothing happens.
Have already tried the older versions of firmware V1.0.1 and V1.0.2, all with the same result.
What can I do now?

Robin2 :Layers out of alignment with PULSE_DELAY 5 #Pulse hold time (unit: machine cycle)

Hi,
I have experienced layer not aligned with PULSE_DELAY 5 #Pulse hold time (unit: machine cycle).
5 is anfortunatly the dafault value of Robin2_cfg.txt configuration file.
I have not found any explanation about PULSE_DELAY parameter. I am currently using the value 50 with acceptable results
Can you explain what the correct value must be ?
robin2_cfg.txt

It is impossible to use its board, it has potential, but it remains to polish things

How can I fix this bug in Marlin bugfix-2.x.x?

Error: Unknown environment names 'MKS_ROBIN2'. Valid names are 'MightyBoard1280, MightyBoard2560, DUE_USB, DUE_archim_debug, STM32F070CB_malyan, malyan_M300, esp32, include_tree, STM32F401VE_STEVAL, STM32F7, STM32F103RC_btt_512K_USB, sanguino1284p, FLYF407ZG, STM32F103RE_btt, STM32F4, mks_robin_stm32, STM32F103RC, LPC1769, mks_robin_pro, mks_robin_e3, FYSETC_F6_13, SAMD51_grandcentral_m4, melzi_optimized, STM32F103RC_btt_USB, chitu_f103, STM32F103VE_GTM32, teensy36, at90usb1286_cdc, ARMED, jgaurora_a5s_a1, FYSETC_S6, DUE, DUE_archim, mks_robin_mini, STM32F103RET6_creality, STM32F070RB_malyan, mega2560, mks_robin, STM32F103RC_btt, rumba32, LERDGEX, rambo, LERDGEK, teensy35, mega1280, mks_robin_nano35, BIGTREE_SKR_PRO, at90usb1286_dfu, teensy41, sanguino644p, melzi_optiboot, chitu_v5_gpio_init, melzi, DUE_debug, teensy31, FYSETC_F6_14, STM32F103VE_longer, STM32F103RC_meeb, STM32F103RC_btt_512K, mks_robin_e3p, STM32F103CB_malyan, BIGTREE_BTT002, LERDGES, linux_native, trigorilla_pro, STM32F407VE_black, STM32F103RC_fysetc, mks_robin_lite3, mks_robin_lite, LPC1768, STM32F103RE, BIGTREE_GTR_V1_0, STM32F103RE_btt_USB, mega2560ext'

It is impossible to compile for this board.

There is also no pin reference so they PINs, be redirected for various uses.
PLEASE RELEASE IT.

MKS Robin 2 doesnt update firmware and doesnt work screen

İ connect my PC to MKS Robin 2 3d printer.i arrang eeeprom in repetier host program. After that i make change MKS Robin 2 config. And i install SD card MKS Robin 2. İ push the reset button.. than the screen and reset button doesnt work. i dosnt install New firmware SD card.the computer connect the card. What way Should i follow solve this problem

filament change position

I have an MKS Robin 2 with the current firmware version 1.03, if I go to filament change while printing is in progress, it moves to the point specified in the config and immediately back to the previous printing position. then when the print job is started again, it feeds matterial and starts. this always results in a blob of matterial where the nozzle then has to pass through and mess up the part.

so it is in the config

position of hotend for filament change and pause print

FILAMENT_CHANGE_X_POS 5 # X position of hotend for filament change and pause print
FILAMENT_CHANGE_Y_POS 5 # Y position of hotend for filament change and pause print
FILAMENT_CHANGE_Z_ADD 5 # Z addition of hotend (lift) for filament change and pause print

MKS robin 2 and MKS LV8729 noise issue

I have just setup a new MKS robin 2 running v1.0.3 firmware.
When the print is running, there seems to be a noticiable clicking/stutter sound coming from the x and y stepper motors. This is only noticable mainly when running curves/circles etc.
I have tried to run 1/128 steps and it worst. Im now running 1/32 steps and its still there.

Printing from SD Card.

Sounds like skipping steps. but its not actually skipping.

I should also note, this is running on a Corexy

Any idea?

Ive found a video that is doing the exact same thing as mine. Please help
https://www.youtube.com/watch?v=VuU9CssOD0Y

Firmware source

Hello,

As you dont support Robin2 any more, would you mind to share firmware source?

No manual movement in robin2