mattytrentini / led_strip Goto Github PK
View Code? Open in Web Editor NEWControl a LED strip using an ESP8266, PWM, an N-Channel MOSFET, a rotary encoder and some Micropython
License: MIT License
Control a LED strip using an ESP8266, PWM, an N-Channel MOSFET, a rotary encoder and some Micropython
License: MIT License
Currently the LED strip driving calls are all nestled within the main.py file. It would be good to extract these calls / functions, neaten them up, and place them in a class so that multiple LED strips can be driven at once. Fading and debouncing logic will have to be re-designed to a non-blocking implementation.
A Passive InfraRed sensor could be used to detect when someone is nearby and turn on the LED strip automatically. Just need to hook this in to the broken-out GPIO and monitor it for changes.
I tend to prefer hardware solutions (10nF cap across switch?). But could be done in software too.
Note that debouncing isn't really a problem when the brightness is high - the fade duration means that the debounce has stabilised by the time the fade is complete.
So, to test, reduce the brightness to the lowest setting and press the switch repeatedly. It's pretty easy to reproduce a repeat event (it will fade off then on - or vice versa - for one button click).
There are obvious steps in changing the brightness when fading, it should be smoother. If we put a simple fade routine in a (non-async) loop:
from machine import Pin, PWM
from time import sleep_ms
led=PWM(Pin(22))
for i in range(1024):
led.duty(i)
sleep_ms(5)
It's very smooth.
A few issues to consider:
Upon opening the led_strip_breadboard.fzz Fritzing file, an error pops up stating, "Unable to find the following part: 'Camdenboss_CTB0158-2_5_08mm_pitch_90deg_terminals' at '/home/USER/Documents/fritzing-VERSION/fritzing-parts/core/Camdenboss_CTB0158-2_5_08mm_pitch_90deg_terminals.fzp' ". Error seen on Fritzing 0.9.3b.
In the Rev A shield PCB, there are no LEDs built into the Design. This means testing functionality is harder than would be ideal.
Preferred setup would be to have an LED to show power on the 12V and 3V3 rails, as well as an LED across each of the LED strip terminals to show when they're powered. This should be implemented for Rev B of the PCB.
The fade routine should be able to be interrupted. Specifically, if the strip is off and the switch is pushed a fade-in should begin...if the switch is pushed again before the fade is complete then the fade-in should be stopped and a fade-out should begin until the strip is off.
Currently the value of the encoder is recorded even when the LED strip is off.
This means that the LED strip can be turned off and the brightness changed before turning it on again. That's unexpected behaviour! Should ignore the encoder while the strip is off.
In the Rev A version of the shield PCB, there is no silk screen annotations on the connectors. This means that prior knowledge of the board is required for knowing how to connect the LED strips, and could very easily result in the strips being wired backwards (unlikely to be damaging for the strips, but could lead to some confusion).
This should be rectified for Rev B of the PCB.
The debounce resistors have too high a resistance (27k), which means that they cannot successfully overcome the pull-up resistors inside the ESP (10k). For example: Pressing the rotary encoder button results in a voltage of 2.5V, which does not trigger the button press interrupt.
Currently the LEDs are briefly on when the board is powered up before they turn off - see #18. Pull-down resistors need to be added to the LED_DRIVE_x nets in order to aid in resolving this issue.
Currently when the button is pressed the LED's come on temporarily at full brightness then back to completely off.
When the rotary encoder is pressed it allows the LED's to be lit but starts them at 0 brightness. Once the encoder is turned it enforces a minimum brightness.
What should happen is that when the application starts the LED's should - perhaps - turn on and off quickly but with a very dim brightness. Then, if the rotary encoder is pressed, the LED's should be lit to the minimum brightness.
Notice that the fade looks great when the brightness is near max. Notice too that there's barely any fade when the brightness reduces to below about half.
It's because the number of fade steps is simply however many values are between the brightness level (of a range from 0-1020) and 0. The pause between each step change is constant (1ms by default) so the fade is longer for brighter values.
Should divide the desired duration by the number of steps. Maybe have some corner cases when brightness is low (ie at 1 or 2).
A declarative, efficient, and flexible JavaScript library for building user interfaces.
๐ Vue.js is a progressive, incrementally-adoptable JavaScript framework for building UI on the web.
TypeScript is a superset of JavaScript that compiles to clean JavaScript output.
An Open Source Machine Learning Framework for Everyone
The Web framework for perfectionists with deadlines.
A PHP framework for web artisans
Bring data to life with SVG, Canvas and HTML. ๐๐๐
JavaScript (JS) is a lightweight interpreted programming language with first-class functions.
Some thing interesting about web. New door for the world.
A server is a program made to process requests and deliver data to clients.
Machine learning is a way of modeling and interpreting data that allows a piece of software to respond intelligently.
Some thing interesting about visualization, use data art
Some thing interesting about game, make everyone happy.
We are working to build community through open source technology. NB: members must have two-factor auth.
Open source projects and samples from Microsoft.
Google โค๏ธ Open Source for everyone.
Alibaba Open Source for everyone
Data-Driven Documents codes.
China tencent open source team.