GPIO access for CHIP on Node.JS
Support for the 4.4 kernel CHIPs has been added thanks to https://github.com/nkolban.
$ npm install chip-gpio --save
You must have build-essential installed for this module to install correctly, which can be installed using
$ sudo apt-get install build-essential
Credit to fivdi for providing the epoll module for hardware interrupts and the onoff module which this was based on.
The available pins are XIO-P0 to XIO-P7. Assume that there's an LED on GPIO #6 and a momentary push button on GPIO #7.
When the button is pressed the LED should turn on, when it's released the LED should turn off. This can be achieved with the following code:
var Gpio = require('chip-gpio').Gpio;
var btn = new Gpio(7, 'in', 'both', {
debounceTimeout: 500
});
var led = new Gpio(6, 'out');
btn.watch(function (err, value) {
if (err) {
throw err;
}
led.write(led.read() == 1 ? 0 : 1);
});
function exit() {
btn.unexport();
led.unexport();
process.exit();
}
process.on('SIGINT', exit);
Here two Gpio objects are being created. One called led for the LED on GPIO #6 which is an output, and one called btn for the momentary push button on GPIO #7 which is an input. In addition to specifying that the button is an input, the constructors optional third argument is used to specify that 'both' rising and falling interrupt edges should be configured for the button GPIO as both button presses and releases should be handled. Furthermore, the debounceTimeout option is specified, meaning that a new interrupt cannot be generated before 500ms after another
Internally onoff uses sysfs files located at /sys/class/gpio to access GPIOs and the epoll module to detect hardware interrupts. The Linux GPIO sysfs interface for userspace is documented here. It's a relatively simple interface which can be used to ask the Linux kernel to export control of a GPIO to userspace. After control of a GPIO has been exported to userspace, the GPIO can be configured as an input or output. Thereafter, the state of an input can be read, and the state of an output can be written. Some systems will also allow the state of a output to be read. The GPIO sysfs interface can also be used for interrupt detection.
Returns a new Gpio object that can be used to access a GPIO.
- gpio - An unsigned integer specifying the GPIO number.
- direction - A string specifying whether the GPIO should be configured as an input or output. The valid values are: 'in', 'out', 'high', and 'low'. 'high' and 'low' are variants of 'out' that configure the GPIO as an output with an initial level of high or low respectively.
- [edge] - An optional string specifying the interrupt generating edge or edges for the GPIO. The valid values are: 'none', 'rising', 'falling' or 'both'. The default value is 'none' indicating that the GPIO does not generate interrupts. On Linux kernels prior to 3.13 it was possible for both inputs and outputs to generate interrupts. The 3.13 kernel dropped support for interrupt generating outputs, irrespective of whether the underlying hardware supports them or not.
Read GPIO value synchronously. Returns the number 0 or 1 to represent the state of the GPIO.
Write GPIO value synchronously.
- value - The number 0 or 1.
Watch for hardware interrupts on the GPIO. The edge argument that was passed to the constructor determines which hardware interrupts to watch for.
- callback - A callback that gets two arguments (err, value), where err is reserved for an error object and value is the number 0 or 1 and represents the state of the GPIO. The value can also be used to determine whether the interrupt occurred on a rising or falling edge. A value of 0 implies a falling edge interrupt and a value of 1 implies a rising edge interrupt.
Stop watching for hardware interrupts on the GPIO. If callback is specified, only that particular callback is removed. Otherwise all callbacks are removed.
- [callback] - The callback to remove.
Returns the string 'in' or 'out' indicating whether the GPIO is an input or output.
Set GPIO direction.
- direction - A string specifying whether the GPIO should be configured as an input or output. The valid values are 'in' and 'out'.
Returns the string 'none', 'falling', 'rising', or 'both' indicating the interrupt generating edge or edges for the GPIO.
Set GPIO interrupt generating edge
- edge - A string specifying the interrupt generating edge or edges for the GPIO. The valid values are: 'none', 'rising', 'falling' or 'both'. On Linux kernels prior to 3.13 it was possible for both inputs and outputs to generate interrupts. The 3.13 kernel dropped support for interrupt generating outputs, irrespective of whether the underlying hardware supports them or not.
Reverse the effect of exporting the GPIO to userspace