motioneye-project/motioneyeos

A Video Surveillance OS For Single-board Computers

motionEyeOS is a Linux distribution that turns your single board computer into a video surveillance system. Check out the wiki for more details.

Due to personal reasons I can no longer be actively involved with this project. If anyone is interested in taking it over, please contact me and we'll work out together a hand-off plan.

motioneyeos's Issues

Raspberry Pi rev2 is too slow

Hi,

motionEyeOS is great, but i have a Rasberry PI rev2 (512mo de ram) and in motion detection mode, the CPU is up to 90% and is too slow to detect, send mail ...

This device is the lower speed of the devices compatibles. But for the motionEyeOS, what is the best card ?

Thanks

Unable to install noip for dynamic DNS setup

I refer to the instructions given by http://pimylifeup.com/raspberry-pi-port-forwarding/

The "make" command is missing and thus I am unable to create a binary from the "noip" source files. I tried installing "make", but it seems there is no packet manager such as apt-get available in this OS. I also tried to directly use the binaries supplied by the noip folder, but none of them are compatible for the Raspberry Pi 2 architecture. Now I'm thinking of compiling the source file on a virtual machine identical to that of the rpi2, but thought I might come for assistance first. Thanks in advance.

Update : 20151021

Hello,

When i go to the MotionEyeos and hit Software Update i do not get the update ......
It keeps saying : motionEye is up to date (current version:: 20151011)

protocol rtsp not supported - release 20151103

With the latest release when trying to add a rtsp network camera im unable to do so and
get the error 'protocol rtsp not supported'.

The pre-release versions worked fine.

Cannot use POST

I tried to create a Web Hook Notification, but whenever I change the HTTP Method from GET to POST, it fails to change anything. It looks like it went through but when I go back to the settings it says GET again.

Date is incorrect.

Raspberry Pi B+ running version 20151021 with the date settings as follows:

Date Method HTTP
Date HTTP Host google.com
Date Updating Timeout 10
Date Updating Interval 900

Current time is 1207pm but the time stamp is showing 507pm. Did I mess up a setting? Not sure how to correct the time...

[rpi2] Activating Fast Network Camera reboot and no more available

I've just installed version 20151021. When I switch on Fast Network Camera, it reboot my Raspberry Pi 2 and then it became impossible to access it : Page Web inaccessible ERR_CONNECTION_REFUSED in Chromium. I've waited several minutes and tried several times and the result is same.

boot.log

---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
/dev/mmcblk0p3: Bad magic number in super-block while opening filesystem
Formatting data partition
Discarding device blocks:   4096/916608�������������528384/916608�������������             �������������done                            
Creating filesystem with 916608 4k blocks and 229376 inodes
Filesystem UUID: 0db302a7-20a9-4478-a399-e5ffdf72bf95
Superblock backups stored on blocks: 
    32768, 98304, 163840, 229376, 294912, 819200, 884736

Allocating group tables:  0/28�����     �����done                            
Writing inode tables:  0/28�����     �����done                            
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information:  0/28�����     �����done

Setting empty admin password
Starting wpa_supplicant: done
Starting network: wlan0: starting dhclient
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:f7:b1:f7  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.244  netmask 255.255.255.0  broadcast 192.168.0.255
        ether 74:da:38:0c:c6:d5  txqueuelen 1000  (Ethernet)
        RX packets 8  bytes 1894 (1.8 KiB)
        RX errors 0  dropped 2  overruns 0  frame 0
        TX packets 5  bytes 1398 (1.3 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
ssh-keygen: generating new host keys: RSA1 RSA DSA ECDSA ED25519 
Starting sshd: done
Setting current date using http: Fri Oct 23 08:31:38 UTC 2015
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting motioneye: done
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down motioneye: done
---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
Setting empty admin password
Starting wpa_supplicant: done
Starting network: wlan0: starting dhclient
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:f7:b1:f7  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.244  netmask 255.255.255.0  broadcast 192.168.0.255
        ether 74:da:38:0c:c6:d5  txqueuelen 1000  (Ethernet)
        RX packets 11  bytes 3164 (3.0 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 5  bytes 1406 (1.3 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
Starting sshd: done
Setting current date using http: Fri Oct 23 08:32:35 UTC 2015
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting motioneye: done
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down streameye: Shutting down motioneye: failed
---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
Setting empty admin password
Starting wpa_supplicant: done
Starting network: wlan0: starting dhclient
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:f7:b1:f7  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.244  netmask 255.255.255.0  broadcast 192.168.0.255
        ether 74:da:38:0c:c6:d5  txqueuelen 1000  (Ethernet)
        RX packets 17  bytes 6432 (6.2 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 5  bytes 1398 (1.3 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
Starting sshd: done
Setting current date using http: Fri Oct 23 08:37:23 UTC 2015
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting streameye: done
Starting motioneye: failed
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down streameye: Shutting down motioneye: failed
---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
Setting empty admin password
Starting wpa_supplicant: done
Starting network: wlan0: starting dhclient
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:f7:b1:f7  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.244  netmask 255.255.255.0  broadcast 192.168.0.255
        ether 74:da:38:0c:c6:d5  txqueuelen 1000  (Ethernet)
        RX packets 6  bytes 1610 (1.5 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 5  bytes 1406 (1.3 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
Starting sshd: done
Setting current date using http: Fri Oct 23 08:39:47 UTC 2015
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting streameye: done
Starting motioneye: failed
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down streameye: Shutting down motioneye: failed
---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
Setting empty admin password
Starting wpa_supplicant: done
Starting network: wlan0: starting dhclient
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:f7:b1:f7  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.244  netmask 255.255.255.0  broadcast 192.168.0.255
        ether 74:da:38:0c:c6:d5  txqueuelen 1000  (Ethernet)
        RX packets 11  bytes 2515 (2.4 KiB)
        RX errors 0  dropped 1  overruns 0  frame 0
        TX packets 5  bytes 1398 (1.3 KiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
Starting sshd: done
Setting current date using http: Fri Oct 23 08:42:13 UTC 2015
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting streameye: done
Starting motioneye: 

messages

Jan  1 00:00:16 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:16 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:16 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:16 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:20 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6
Jan  1 00:00:26 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 8
Jan  1 00:00:26 meye-d6f7b1f7 daemon.info dhclient: DHCPREQUEST on wlan0 to 255.255.255.255 port 67
Jan  1 00:00:26 meye-d6f7b1f7 daemon.info dhclient: DHCPOFFER from 192.168.0.253
Jan  1 00:00:26 meye-d6f7b1f7 daemon.info dhclient: DHCPACK from 192.168.0.253
Jan  1 00:00:26 meye-d6f7b1f7 daemon.info dhclient: bound to 192.168.0.244 -- renewal in 3250 seconds.
Jan  1 00:00:33 meye-d6f7b1f7 auth.info sshd[596]: Server listening on 0.0.0.0 port 22.
Oct 23 08:31:38 meye-d6f7b1f7 daemon.notice proftpd[624]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Oct 23 08:31:38 meye-d6f7b1f7 cron.info crond[632]: crond (busybox 1.23.2) started, log level 8
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err nmbd[651]: [2015/10/23 08:31:39.118665,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err nmbd[651]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connections
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]: [2015/10/23 08:31:39.193718,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]: [2015/10/23 08:31:39.221541,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]: [2015/10/23 08:31:39.221995,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]: [2015/10/23 08:31:39.249524,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]: [2015/10/23 08:31:39.250023,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:31:39 meye-d6f7b1f7 daemon.err smbd[644]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 705
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Oct 23 08:31:42 meye-d6f7b1f7 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Oct 23 08:31:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Oct 23 08:31:44 meye-d6f7b1f7 daemon.info init: starting pid 719, tty '': '/sbin/userinit'
Oct 23 08:31:44 meye-d6f7b1f7 daemon.info init: starting pid 720, tty '/dev/tty1': '/sbin/getty -L tty1 115200 vt100'
Oct 23 08:32:02 meye-d6f7b1f7 daemon.err nmbd[651]: [2015/10/23 08:32:02.146987,  0] ../source3/nmbd/nmbd_become_lmb.c:397(become_local_master_stage2)
Oct 23 08:32:02 meye-d6f7b1f7 daemon.err nmbd[651]:   *****
Oct 23 08:32:02 meye-d6f7b1f7 daemon.err nmbd[651]:   
Oct 23 08:32:02 meye-d6f7b1f7 daemon.err nmbd[651]:   Samba name server MEYE-D6F7B1F7 is now a local master browser for workgroup MOTIONEYE on subnet 192.168.0.244
Oct 23 08:32:02 meye-d6f7b1f7 daemon.err nmbd[651]:   
Oct 23 08:32:02 meye-d6f7b1f7 daemon.err nmbd[651]:   *****
Oct 23 08:32:14 meye-d6f7b1f7 daemon.info init: starting pid 781, tty '/dev/null': '/etc/init.d/rcK'
Oct 23 08:32:14 meye-d6f7b1f7 syslog.info syslogd exiting
Jan  1 00:00:02 meye-d6f7b1f7 syslog.info syslogd started: BusyBox v1.23.2
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:06 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPREQUEST on wlan0 to 255.255.255.255 port 67
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPOFFER from 192.168.0.253
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPACK from 192.168.0.253
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: bound to 192.168.0.244 -- renewal in 2991 seconds.
Jan  1 00:00:10 meye-d6f7b1f7 auth.info sshd[538]: Server listening on 0.0.0.0 port 22.
Oct 23 08:32:35 meye-d6f7b1f7 cron.info crond[571]: crond (busybox 1.23.2) started, log level 8
Oct 23 08:32:35 meye-d6f7b1f7 daemon.notice proftpd[564]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err nmbd[589]: [2015/10/23 08:32:36.092085,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err nmbd[589]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connections
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]: [2015/10/23 08:32:36.191273,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]: [2015/10/23 08:32:36.214988,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]: [2015/10/23 08:32:36.215540,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]: [2015/10/23 08:32:36.238287,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]: [2015/10/23 08:32:36.238711,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:32:36 meye-d6f7b1f7 daemon.err smbd[585]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 626
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Oct 23 08:32:37 meye-d6f7b1f7 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Oct 23 08:32:37 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Oct 23 08:32:38 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Oct 23 08:32:38 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Oct 23 08:32:38 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:32:38 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:32:38 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Oct 23 08:32:38 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Oct 23 08:32:42 meye-d6f7b1f7 daemon.info init: starting pid 662, tty '': '/sbin/userinit'
Oct 23 08:32:42 meye-d6f7b1f7 daemon.info init: starting pid 663, tty '/dev/tty1': '/sbin/getty -L tty1 115200 vt100'
Oct 23 08:32:59 meye-d6f7b1f7 daemon.err nmbd[589]: [2015/10/23 08:32:59.121208,  0] ../source3/nmbd/nmbd_become_lmb.c:397(become_local_master_stage2)
Oct 23 08:32:59 meye-d6f7b1f7 daemon.err nmbd[589]:   *****
Oct 23 08:32:59 meye-d6f7b1f7 daemon.err nmbd[589]:   
Oct 23 08:32:59 meye-d6f7b1f7 daemon.err nmbd[589]:   Samba name server MEYE-D6F7B1F7 is now a local master browser for workgroup MOTIONEYE on subnet 192.168.0.244
Oct 23 08:32:59 meye-d6f7b1f7 daemon.err nmbd[589]:   
Oct 23 08:32:59 meye-d6f7b1f7 daemon.err nmbd[589]:   *****
Oct 23 08:33:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 2
Oct 23 08:33:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
Oct 23 08:33:24 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: End of event 1
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: End of event 2
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd - Finishing
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Closing
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] motion_web_control: motion-httpd thread exit
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: Thread exiting
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] stream_stop: Closing motion-stream listen socket & active motion-stream sockets
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] stream_stop: Closed motion-stream listen socket & active motion-stream sockets
Oct 23 08:35:50 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_close: Closing video device /dev/video0
Oct 23 08:35:51 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Threads finished
Oct 23 08:35:52 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Motion terminating
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 993
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Oct 23 08:35:53 meye-d6f7b1f7 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Oct 23 08:35:53 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Oct 23 08:35:57 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 20
Oct 23 08:35:57 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
Oct 23 08:36:10 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: End of event 1
Oct 23 08:36:10 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: Thread exiting
Oct 23 08:36:10 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] stream_stop: Closing motion-stream listen socket & active motion-stream sockets
Oct 23 08:36:10 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] stream_stop: Closed motion-stream listen socket & active motion-stream sockets
Oct 23 08:36:10 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_close: Closing video device /dev/video0
Oct 23 08:36:11 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd - Finishing
Oct 23 08:36:11 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Closing
Oct 23 08:36:11 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] motion_web_control: motion-httpd thread exit
Oct 23 08:36:12 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Threads finished
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Motion terminating
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 1032
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Oct 23 08:36:13 meye-d6f7b1f7 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (1024x768)
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (1024x768) bytesperlines 1024 sizeimage 1179648 colorspace 00000001
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Oct 23 08:36:13 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Oct 23 08:36:18 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 17
Oct 23 08:36:18 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
Oct 23 08:36:42 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: End of event 1
Oct 23 08:37:04 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 18
Oct 23 08:37:04 meye-d6f7b1f7 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 2
Oct 23 08:37:04 meye-d6f7b1f7 daemon.info init: starting pid 1237, tty '/dev/null': '/etc/init.d/rcK'
Oct 23 08:37:04 meye-d6f7b1f7 syslog.info syslogd exiting
Jan  1 00:00:02 meye-d6f7b1f7 syslog.info syslogd started: BusyBox v1.23.2
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:06 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPREQUEST on wlan0 to 255.255.255.255 port 67
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPOFFER from 192.168.0.253
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPACK from 192.168.0.253
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: bound to 192.168.0.244 -- renewal in 2848 seconds.
Jan  1 00:00:11 meye-d6f7b1f7 auth.info sshd[542]: Server listening on 0.0.0.0 port 22.
Oct 23 08:37:23 meye-d6f7b1f7 cron.info crond[572]: crond (busybox 1.23.2) started, log level 8
Oct 23 08:37:23 meye-d6f7b1f7 daemon.notice proftpd[564]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err nmbd[591]: [2015/10/23 08:37:24.091260,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err nmbd[591]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connections
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]: [2015/10/23 08:37:24.198091,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]: [2015/10/23 08:37:24.227350,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]: [2015/10/23 08:37:24.227901,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]: [2015/10/23 08:37:24.257577,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]: [2015/10/23 08:37:24.258082,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:37:24 meye-d6f7b1f7 daemon.err smbd[588]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:37:47 meye-d6f7b1f7 daemon.err nmbd[591]: [2015/10/23 08:37:47.119831,  0] ../source3/nmbd/nmbd_become_lmb.c:397(become_local_master_stage2)
Oct 23 08:37:47 meye-d6f7b1f7 daemon.err nmbd[591]:   *****
Oct 23 08:37:47 meye-d6f7b1f7 daemon.err nmbd[591]:   
Oct 23 08:37:47 meye-d6f7b1f7 daemon.err nmbd[591]:   Samba name server MEYE-D6F7B1F7 is now a local master browser for workgroup MOTIONEYE on subnet 192.168.0.244
Oct 23 08:37:47 meye-d6f7b1f7 daemon.err nmbd[591]:   
Oct 23 08:37:47 meye-d6f7b1f7 daemon.err nmbd[591]:   *****
Oct 23 08:39:29 meye-d6f7b1f7 daemon.info init: starting pid 1357, tty '': '/sbin/userinit'
Oct 23 08:39:29 meye-d6f7b1f7 daemon.info init: starting pid 1358, tty '/dev/null': '/etc/init.d/rcK'
Oct 23 08:39:29 meye-d6f7b1f7 syslog.info syslogd exiting
Jan  1 00:00:02 meye-d6f7b1f7 syslog.info syslogd started: BusyBox v1.23.2
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:06 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 4
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 10
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPREQUEST on wlan0 to 255.255.255.255 port 67
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPOFFER from 192.168.0.253
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: DHCPACK from 192.168.0.253
Jan  1 00:00:10 meye-d6f7b1f7 daemon.info dhclient: bound to 192.168.0.244 -- renewal in 2991 seconds.
Jan  1 00:00:10 meye-d6f7b1f7 auth.info sshd[538]: Server listening on 0.0.0.0 port 22.
Oct 23 08:39:47 meye-d6f7b1f7 cron.info crond[570]: crond (busybox 1.23.2) started, log level 8
Oct 23 08:39:47 meye-d6f7b1f7 daemon.notice proftpd[563]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err nmbd[590]: [2015/10/23 08:39:48.096064,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err nmbd[590]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connections
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]: [2015/10/23 08:39:48.200421,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]: [2015/10/23 08:39:48.230327,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]: [2015/10/23 08:39:48.231092,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]: [2015/10/23 08:39:48.262336,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]: [2015/10/23 08:39:48.262831,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:39:48 meye-d6f7b1f7 daemon.err smbd[584]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:40:11 meye-d6f7b1f7 daemon.err nmbd[590]: [2015/10/23 08:40:11.125398,  0] ../source3/nmbd/nmbd_become_lmb.c:397(become_local_master_stage2)
Oct 23 08:40:11 meye-d6f7b1f7 daemon.err nmbd[590]:   *****
Oct 23 08:40:11 meye-d6f7b1f7 daemon.err nmbd[590]:   
Oct 23 08:40:11 meye-d6f7b1f7 daemon.err nmbd[590]:   Samba name server MEYE-D6F7B1F7 is now a local master browser for workgroup MOTIONEYE on subnet 192.168.0.244
Oct 23 08:40:11 meye-d6f7b1f7 daemon.err nmbd[590]:   
Oct 23 08:40:11 meye-d6f7b1f7 daemon.err nmbd[590]:   *****
Oct 23 08:41:53 meye-d6f7b1f7 daemon.info init: starting pid 1355, tty '': '/sbin/userinit'
Oct 23 08:41:53 meye-d6f7b1f7 daemon.info init: starting pid 1356, tty '/dev/null': '/etc/init.d/rcK'
Oct 23 08:41:53 meye-d6f7b1f7 syslog.info syslogd exiting
Jan  1 00:00:02 meye-d6f7b1f7 syslog.info syslogd started: BusyBox v1.23.2
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:03 meye-d6f7b1f7 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:05 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 6
Jan  1 00:00:11 meye-d6f7b1f7 daemon.info dhclient: DHCPDISCOVER on wlan0 to 255.255.255.255 port 67 interval 9
Jan  1 00:00:11 meye-d6f7b1f7 daemon.info dhclient: DHCPREQUEST on wlan0 to 255.255.255.255 port 67
Jan  1 00:00:11 meye-d6f7b1f7 daemon.info dhclient: DHCPOFFER from 192.168.0.253
Jan  1 00:00:11 meye-d6f7b1f7 daemon.info dhclient: DHCPACK from 192.168.0.253
Jan  1 00:00:11 meye-d6f7b1f7 daemon.info dhclient: bound to 192.168.0.244 -- renewal in 3044 seconds.
Jan  1 00:00:11 meye-d6f7b1f7 auth.info sshd[538]: Server listening on 0.0.0.0 port 22.
Oct 23 08:42:13 meye-d6f7b1f7 cron.info crond[567]: crond (busybox 1.23.2) started, log level 8
Oct 23 08:42:13 meye-d6f7b1f7 daemon.notice proftpd[560]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err nmbd[587]: [2015/10/23 08:42:14.099863,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err nmbd[587]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connections
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]: [2015/10/23 08:42:14.207607,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]: [2015/10/23 08:42:14.241091,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]: [2015/10/23 08:42:14.241816,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]: [2015/10/23 08:42:14.273246,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]: [2015/10/23 08:42:14.273693,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 23 08:42:14 meye-d6f7b1f7 daemon.err smbd[581]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 23 08:42:37 meye-d6f7b1f7 daemon.err nmbd[587]: [2015/10/23 08:42:37.128226,  0] ../source3/nmbd/nmbd_become_lmb.c:397(become_local_master_stage2)
Oct 23 08:42:37 meye-d6f7b1f7 daemon.err nmbd[587]:   *****
Oct 23 08:42:37 meye-d6f7b1f7 daemon.err nmbd[587]:   
Oct 23 08:42:37 meye-d6f7b1f7 daemon.err nmbd[587]:   Samba name server MEYE-D6F7B1F7 is now a local master browser for workgroup MOTIONEYE on subnet 192.168.0.244
Oct 23 08:42:37 meye-d6f7b1f7 daemon.err nmbd[587]:   
Oct 23 08:42:37 meye-d6f7b1f7 daemon.err nmbd[587]:   *****

motioneye.log

2015-10-23 08:31:40: [motioneye]     INFO: hello! this is motionEye server 20151021
2015-10-23 08:31:40: [motioneye]     INFO: main config file /data/etc/motion.conf does not exist, using default values
2015-10-23 08:31:40: [motioneye]     INFO: cleanup started
2015-10-23 08:31:40: [motioneye]     INFO: wsswitch started
2015-10-23 08:31:40: [motioneye]     INFO: thumbnailer started
2015-10-23 08:31:40: [motioneye]     INFO: mjpg client garbage collector started
2015-10-23 08:31:40: [motioneye]     INFO: smb mounts started
2015-10-23 08:31:41: [motioneye]     INFO: server started
2015-10-23 08:31:41: [motioneye]     INFO: adding new camera with id 1...
2015-10-23 08:31:42: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:31:42: [motioneye]     INFO: main config file /data/etc/motion.conf does not exist, using default values
2015-10-23 08:31:44: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:31:48: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:31:48: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:32:14: [motioneye]     INFO: rebooting
2015-10-23 08:32:14: [motioneye]     INFO: executing "/sbin/reboot"
2015-10-23 08:32:15: [motioneye]     INFO: interrupt signal received, shutting down...
2015-10-23 08:32:15: [motioneye]     INFO: server stopped
2015-10-23 08:32:19: [motioneye]     INFO: motion stopped
2015-10-23 08:32:19: [motioneye]     INFO: smb mounts stopped
2015-10-23 08:32:19: [motioneye]     INFO: bye!
2015-10-23 08:32:19: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
2015-10-23 08:32:19: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
2015-10-23 08:32:37: [motioneye]     INFO: hello! this is motionEye server 20151021
2015-10-23 08:32:39: [motioneye]     INFO: cleanup started
2015-10-23 08:32:39: [motioneye]     INFO: wsswitch started
2015-10-23 08:32:39: [motioneye]     INFO: thumbnailer started
2015-10-23 08:32:39: [motioneye]     INFO: mjpg client garbage collector started
2015-10-23 08:32:39: [motioneye]     INFO: smb mounts started
2015-10-23 08:32:39: [motioneye]     INFO: server started
2015-10-23 08:32:43: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:32:43: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:35:55: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:35:55: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:36:15: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:36:15: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-23 08:37:02: [motioneye]    ERROR: streameye restart failed
2015-10-23 08:37:02: [motioneye]     INFO: adding new camera with id 1...
2015-10-23 08:37:03: [motioneye]    ERROR: HTTP 400: Bad Request (unknown operation)
2015-10-23 08:37:03: [motioneye]  WARNING: 400 GET /picture/1/current/?_=1445589423760&_username=admin&_signature=5b5fb8d0f6e582b60d160a9a7fd9e722aa51b54f (192.168.0.10) 14.98ms
2015-10-23 08:37:04: [motioneye]    ERROR: HTTP 400: Bad Request (unknown operation)
2015-10-23 08:37:04: [motioneye]  WARNING: 400 GET /picture/1/current/?_=1445589425236&_username=admin&_signature=83a3400885387271dec10a169d6178087aab9c52 (192.168.0.10) 5.82ms
2015-10-23 08:37:04: [motioneye]     INFO: rebooting
2015-10-23 08:37:04: [motioneye]     INFO: executing "/sbin/reboot"
2015-10-23 08:37:06: [motioneye]     INFO: interrupt signal received, shutting down...
2015-10-23 08:37:06: [motioneye]     INFO: server stopped
2015-10-23 08:37:07: [motioneye]     INFO: interrupt signal received, shutting down...

raspimjpeg.log

2015-10-23 08:42:15:  INFO: raspimjpeg.py 0.5
2015-10-23 08:42:15:  INFO: hello!

streameye.log

2015-10-23 08:42:14: INFO : streamEye 0.5
2015-10-23 08:42:14: INFO : hello!
2015-10-23 08:42:14: INFO : listening on 0.0.0.0:8081

Request

I would find it very useful if there is more possibility of setting up your camera.
It would be very useful if we could change this :
Sharpness
ISO
Video FPS
Image RES
Video Res

I hope if its possible to set Max resolution to 1920x1080 for video recording,
and for taking pictures 2592×1944 and the possibility to change the ratio of width to height (different aspect ratio's)

It also seems very cool and useful to add image effects / color effects.
For example, night vision , cloudy , sunrise , etc ... Some good configuration what is best for these conditions.

sorry if I post in the wrong sector . I 'm new to gfthub

Crashing .. solid green led

My system keeps crashung and hangs, unable to ssh or access webpage. I get a solid green light and have to power cycle the pi.
Its not consistant, it can run for a day or so then crash and other times for only a few hours.
Ive got images saving to a network share so the sd card shouldnt be the issue although i thought solid green led meant sd boot issue?.
Cant seem to see anything in the logs
Any ideas?

Help installing alsa-utils

Hey Calin, motioneyeos really became great over the years. I'm currently running it on Raspberry Pi 2, and it's working great.

I am currently trying to add support for playing sounds (a request was made on https://github.com/ccrisan/motionpie/issues/180).
snd-usb-audio module is loaded in the kernel.
aplay is not installed by default, it seems the whole alsa-utils package isn't installed.
I did find motioneyeos/package/alsa-utils/Config.in & alsa-utils.hash & alsa-utils.mk in the master branch, so I'm guessing there is some way of enabling alsa-utils. What am I missing here?
Motioneyeos lacks apt-get or any similar tool, so I currently have no way of installing alsa-utils.

Please help me install alsa-utils. If there's an easy solution, please add instructions in your wiki/Tweaks.

Thank you :)

Central server and multiple RPis

Hi,

I just saw a scenario on the wiki page showing multiple RPis connected to a central server. The question is - how to get motioneyeos installed on e.g. CentOS server (not another RPi) so I have a hub there where all my RPis stream to?
Can you provide instruction if such scenario is achievable?

Thanks,

Rafal

email troubles (the "from" field, probably)...

Hi. Sorry to be bothering you, but I'm having troubles with email notifications. The last time they worked for me was on the last version of motionpie. I'm suspecting it has something to do with "from" field in the email being sent. Did you perhaps change something in that sense and could you please tell me if it's possible for a noob to set it back the way it was (editing a config file?) or would you be willing to set it back (if it proves to be the cause of problems). Here are two messages from different mail hosts I've found in the log:

A. - smtp.mail.ru

line 731, in sendmail
SMTPSenderRefused: (550, 'not local sender over smtp'

B. - mail.gmx.com

line 731, in sendmail
SMTPSenderRefused: (550, 'Requested action not taken: mailbox unavailable\nSender address is not allowed.

I've read that gmail "quietly" changes the from field and lets the message through, but these two don't, they return an error.

Thanks in advance!

How to save snapshots/videos on shared folder on network

Hello

I am quite new to the Motion Eye OS (great work btw!), and my problem relays on the save path for the pictures/videos.
I shared a folder (an external hard drive in a laptop, with all the permisions, withouth username and password) on my network, and when i try to configure the file storage as a "Network Share" with the information os the shared folder, it seems that the Motion Eye doesn't recognize the path (no video displays), altough i can access the shared folder from other computers.

Am I doing something wrong? Have I not done something before sharing?

I am using Motion Eye OS on a Raspberry PI 2

Attaching an image for a better reference

Thanks in advance

DD command fails on mac os

I removed the "status=none" and changed the bs to bs=1m

it works.

Cant quite get Motion Detection and email working

Hi

I am still trying to get motion detection and email working, I have tried various settings, but never seem to capture the image of the person for example walking up the the camera, can anyone share their better set up info for the camera and motion detection?

I get a lot of Motion has been detected by camera "Driveway/meye-12b5579b" at 2015-11-23 19:04:35 (Australia/Brisbane). with no attachments as well.

Thanks

Damian

no preview in admin screen if streaming auth is set to digest

So, since the update to the last version, there is no "preview" on admin screen if streaming authentication is set to "digest". If set to basic or none, everything's normal.

firefox view pictures

there is a problem with FF 42 and viewing picture logs
web page is broken

Usb CAM + email notifications problem

Hi,

I'm a newbie..trying to explore motioneyeos. It is awesome as far as the capabilities of it are. But I'm having a few problems

1. USB Camera crashes with grey image saying unable to open video device since.....
   ---Initially when it happened, I modified the config.txt with max_usb_current=1 now it is a bit more stable, but crashes after sometime, but a reboot works

here is the output of motion -n

---

cap.driver: "sonixj"
cap.card: "USB camera"
cap.bus_info: "usb-bcm2708_usb-1.4"

cap.capabilities=0x85200001

[1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
[1] [NTC] [VID] v4l2_get_capability: - READWRITE
[1] [NTC] [VID] v4l2_get_capability: - STREAMING
[1] [NTC] [VID] v4l2_select_input: name = "sonixj", type 0x00000002, status 00000000
[1] [NTC] [VID] v4l2_select_input: - CAMERA
[1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
[1] [NTC] [VID] v4l2_set_pix_format: Config palette index 17 (YU12) doesn't work.
[1] [NTC] [VID] v4l2_set_pix_format: Supported palettes:
[1] [NTC] [VID] v4l2_set_pix_format: (0) JPEG (JPEG)
[1] [NTC] [VID] v4l2_set_pix_format: 0 - JPEG (compressed : 1) (0x4745504a)
[1] [NTC] [VID] v4l2_set_pix_format Selected palette JPEG
[1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette JPEG (352x288)
[1] [NTC] [VID] v4l2_do_set_pix_format: Using palette JPEG (352x288) bytesperlines 352 sizeimage 51278 colorspace 00000007
[1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,255
[1] [NTC] [VID] v4l2_scan_controls: "Brightness", default 128, current 128
[1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range 0,127
[1] [NTC] [VID] v4l2_scan_controls: "Contrast", default 20, current 20
[1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range 0,40
[1] [NTC] [VID] v4l2_scan_controls: "Saturation", default 25, current 25
[1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 24,40
[1] [NTC] [VID] v4l2_scan_controls: "Red Balance", default 32, current 32
[1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 24,40
[1] [NTC] [VID] v4l2_scan_controls: "Blue Balance", default 32, current 32
[1] [NTC] [VID] v4l2_scan_controls: found control 0x00980910, "Gamma", range 0,40
[1] [NTC] [VID] v4l2_scan_controls: "Gamma", default 20, current 20
[1] [ERR] [VID] v4l2_set_mmap: Error requesting buffers 4 for memory map. VIDIOC_REQBUFS: Device or resource busy
[1] [NTC] [VID] vid_v4lx_start: Using V4L1
[1] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device
[1] [NTC] [VID] vid_close: Closing video device /dev/video0

1. Email notifications are not being sent...it says connection terminated unexpectedly. I saw your pre-release which says it is fixed, but I still receive the same problem.

Can you please help me with this?

Thank you,
Anand

web update

Software update can't find new version
"motionEye is up to date (current version: 20151103)"

Add remote motioneye cam

I have tried to add second MotionEyeOS / RPi2 to the first MotionEyeOS / RPi2. Unfortunately, I receive an connection error. Is it because it is not possible to add Remote MotionEyeOS units to a unit already using its egt camera.

To be used in a stand alone MotionEyeOS RPi2 in order to function as a hub MotionEye? Maybe it's just my URL syntax is wrong, but the device tries to connect, so I must believe it is correct.

Can you briefly describe the requirements for a MotionEyeOS hub / RPi2.
How many cameras will be able to handle?
Being shown streaming tumbs from each camera?

It's a great fine piece of software you have developed here. Great respect and gratitude for it.

Craving someone design a 3D printable waterproof encloure to house it all.

Kind regards
Sune Bielefeldt
Denmark

WiFi dongle causes repeated (endless) loops

Installed version 20151011, and everything works very well using an ethernet cable. After following all instructions on enabling WiFi, shutting down, inserting WiFi dongle (I've tried 2 different ones, both that work with Raspbian), the Pi2 goes through a lot of the boot process, but when it gets to starting motionpie, it restarts. The last 2 lines I see are:

Starting motioneye: done
[   36.111257] watchdog stopped

then the process starts all over and ends the same way, with a restart. If I remove the dongle, and go back to using the ethernet cable, everything works fine.

(I tried changing the DHCP to static; no change. I was very, very careful in typing in my SSID and password -- no cut-n-paste -- but that isn't the issue either. As I said, these two WiFi dongles worked well with Raspbian.)

motionpie.log ::::

2015-10-30 04:32:46: [motioneye]     INFO: hello! this is motionEye server 20151011
2015-10-30 04:32:46: [motioneye]     INFO: main config file /data/etc/motion.conf does not exist, using default values
2015-10-30 04:32:46: [motioneye]     INFO: cleanup started
2015-10-30 04:32:46: [motioneye]     INFO: wsswitch started
2015-10-30 04:32:46: [motioneye]     INFO: thumbnailer started
2015-10-30 04:32:47: [motioneye]     INFO: server started
2015-10-30 04:32:47: [motioneye]     INFO: adding new camera with id 1...
2015-10-30 04:32:48: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-30 04:32:48: [motioneye]     INFO: main config file /data/etc/motion.conf does not exist, using default values
2015-10-30 04:32:50: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-30 04:33:20: [motioneye]    ERROR: HTTP 404: Not Found (not found)
2015-10-30 04:33:20: [motioneye]  WARNING: 404 GET /nice%20ports%2C/Tri%6Eity.txt%2ebak (192.168.0.119) 4.12ms
2015-10-30 04:33:20: [motioneye]    ERROR: HTTP 405: Method Not Allowed
2015-10-30 04:33:20: [motioneye]  WARNING: 405 OPTIONS / (192.168.0.119) 3.96ms
2015-10-30 04:33:50: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-30 04:33:50: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-30 04:33:50: [motioneye]  WARNING: control hue not found for device /dev/video0
2015-10-29 23:34:51: [motioneye]     INFO: rebooting
2015-10-29 23:34:51: [motioneye]     INFO: executing "/sbin/reboot"
2015-10-29 23:34:52: [motioneye]     INFO: interrupt signal received, shutting down...
2015-10-29 23:34:52: [motioneye]     INFO: server stopped
2015-10-29 23:34:56: [motioneye]     INFO: motion stopped
2015-10-29 23:34:56: [motioneye]     INFO: SMB shares unmounted
2015-10-29 23:34:56: [motioneye]     INFO: bye!
2015-10-29 23:34:56: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
2015-10-29 23:34:56: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:11: [motioneye]     INFO: hello! this is motionEye server 20151011
1969-12-31 18:00:14: [motioneye]     INFO: cleanup started
1969-12-31 18:00:14: [motioneye]     INFO: wsswitch started
1969-12-31 18:00:14: [motioneye]     INFO: thumbnailer started
1969-12-31 18:00:14: [motioneye]     INFO: server started
1969-12-31 18:00:35: [motioneye]    ERROR: authentication failed for user admin
1969-12-31 18:00:43: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:00:43: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:00:44: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:01:19: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:01:19: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:01:30: [motioneye]     INFO: shutting down
1969-12-31 18:01:30: [motioneye]     INFO: executing "/sbin/poweroff"
1969-12-31 18:01:31: [motioneye]     INFO: interrupt signal received, shutting down...
1969-12-31 18:01:31: [motioneye]     INFO: server stopped
1969-12-31 18:01:34: [motioneye]     INFO: motion stopped
1969-12-31 18:01:34: [motioneye]     INFO: SMB shares unmounted
1969-12-31 18:01:34: [motioneye]     INFO: bye!
1969-12-31 18:01:34: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:01:34: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:29: [motioneye]     INFO: hello! this is motionEye server 20151011
1969-12-31 18:00:32: [motioneye]     INFO: cleanup started
1969-12-31 18:00:32: [motioneye]     INFO: wsswitch started
1969-12-31 18:00:32: [motioneye]     INFO: thumbnailer started
1969-12-31 18:00:32: [motioneye]     INFO: server started
1969-12-31 18:00:34: [motioneye]     INFO: interrupt signal received, shutting down...
1969-12-31 18:00:34: [motioneye]     INFO: server stopped
1969-12-31 18:00:37: [motioneye]     INFO: motion stopped
1969-12-31 18:00:37: [motioneye]     INFO: SMB shares unmounted
1969-12-31 18:00:37: [motioneye]     INFO: bye!
1969-12-31 18:00:37: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:37: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:29: [motioneye]     INFO: hello! this is motionEye server 20151011
1969-12-31 18:00:32: [motioneye]     INFO: cleanup started
1969-12-31 18:00:32: [motioneye]     INFO: wsswitch started
1969-12-31 18:00:32: [motioneye]     INFO: thumbnailer started
1969-12-31 18:00:32: [motioneye]     INFO: server started
1969-12-31 18:00:34: [motioneye]     INFO: interrupt signal received, shutting down...
1969-12-31 18:00:34: [motioneye]     INFO: server stopped
1969-12-31 18:00:37: [motioneye]     INFO: motion stopped
1969-12-31 18:00:37: [motioneye]     INFO: SMB shares unmounted
1969-12-31 18:00:37: [motioneye]     INFO: bye!
1969-12-31 18:00:37: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:37: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:30: [motioneye]     INFO: hello! this is motionEye server 20151011
1969-12-31 18:00:33: [motioneye]     INFO: cleanup started
1969-12-31 18:00:33: [motioneye]     INFO: wsswitch started
1969-12-31 18:00:33: [motioneye]     INFO: thumbnailer started
1969-12-31 18:00:33: [motioneye]     INFO: server started
1969-12-31 18:00:36: [motioneye]     INFO: interrupt signal received, shutting down...
1969-12-31 18:00:36: [motioneye]     INFO: server stopped
1969-12-31 18:00:38: [motioneye]     INFO: motion stopped
1969-12-31 18:00:38: [motioneye]     INFO: SMB shares unmounted
1969-12-31 18:00:38: [motioneye]     INFO: bye!
1969-12-31 18:00:38: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:38: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:30: [motioneye]     INFO: hello! this is motionEye server 20151011
1969-12-31 18:00:32: [motioneye]     INFO: cleanup started
1969-12-31 18:00:32: [motioneye]     INFO: wsswitch started
1969-12-31 18:00:32: [motioneye]     INFO: thumbnailer started
1969-12-31 18:00:32: [motioneye]     INFO: server started
1969-12-31 18:00:35: [motioneye]     INFO: interrupt signal received, shutting down...
1969-12-31 18:00:35: [motioneye]     INFO: server stopped
1969-12-31 18:00:38: [motioneye]     INFO: motion stopped
1969-12-31 18:00:38: [motioneye]     INFO: SMB shares unmounted
1969-12-31 18:00:38: [motioneye]     INFO: bye!
1969-12-31 18:00:38: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:38: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:30: [motioneye]     INFO: hello! this is motionEye server 20151011
1969-12-31 18:00:32: [motioneye]     INFO: cleanup started
1969-12-31 18:00:32: [motioneye]     INFO: wsswitch started
1969-12-31 18:00:32: [motioneye]     INFO: thumbnailer started
1969-12-31 18:00:32: [motioneye]     INFO: server started
1969-12-31 18:00:36: [motioneye]     INFO: interrupt signal received, shutting down...
1969-12-31 18:00:36: [motioneye]     INFO: server stopped
1969-12-31 18:00:38: [motioneye]     INFO: motion stopped
1969-12-31 18:00:38: [motioneye]     INFO: SMB shares unmounted
1969-12-31 18:00:38: [motioneye]     INFO: bye!
1969-12-31 18:00:38: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:38: [relayevent]    ERROR: failed to relay event: [Errno socket error] [Errno 104] Connection reset by peer
1969-12-31 18:00:11: [motioneye]     INFO: hello! this is motionEye server 20151011
1969-12-31 18:00:14: [motioneye]     INFO: cleanup started
1969-12-31 18:00:14: [motioneye]     INFO: wsswitch started
1969-12-31 18:00:14: [motioneye]     INFO: thumbnailer started
1969-12-31 18:00:14: [motioneye]     INFO: server started
1969-12-31 18:00:42: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:00:42: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:00:42: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:01:10: [motioneye]  WARNING: control hue not found for device /dev/video0
1969-12-31 18:01:10: [motioneye]  WARNING: control hue not found for device /dev/video0

:::: motion.log ::::

[0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
[0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
[0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
[0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
[0] [NTC] [ALL] motion_startup: Logging to syslog
[0] [NTC] [ALL] motion_startup: Using default log type (ALL)
[0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
[0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
[0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
[0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
[0] [NTC] [ALL] main: Stream port 8081
[0] [NTC] [ALL] main: Waiting for threads to finish, pid: 731
[1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
[1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
[1] [NTC] [VID] v4l2_get_capability: 
------------------------
cap.driver: "bm2835 mmal"
cap.card: "mmal service 16.1"
cap.bus_info: "platform:bcm2835-v4l2"
cap.capabilities=0x85200005
------------------------
[1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
[1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
[1] [NTC] [VID] v4l2_get_capability: - READWRITE
[1] [NTC] [VID] v4l2_get_capability: - STREAMING
[0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
[1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
[0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
[1] [NTC] [VID] v4l2_select_input: - CAMERA
[0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
[0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
[1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
[1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (1024x768)
[1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (1024x768) bytesperlines 1024 sizeimage 1179648 colorspace 00000001
[1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
[1] [NTC] [VID] v4l2_scan_controls:     "Brightness", default 50, current 50
[1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
[1] [NTC] [VID] v4l2_scan_controls:     "Contrast", default 0, current 0
[1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
[1] [NTC] [VID] v4l2_scan_controls:     "Saturation", default 0, current 0
[1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
[1] [NTC] [VID] v4l2_scan_controls:     "Red Balance", default 1000, current 1000
[1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
[1] [NTC] [VID] v4l2_scan_controls:     "Blue Balance", default 1000, current 1000
[1] [NTC] [VID] vid_v4lx_start: Using V4L2
[1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
[1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
[1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
[1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
[1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
[1] [NTC] [EVT] event_new_video FPS 5
[1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
[1] [NTC] [ALL] motion_loop: End of event 1
[1] [NTC] [EVT] event_new_video FPS 5
[1] [NTC] [ALL] motion_detected: Motion detected - starting event 2
[1] [NTC] [ALL] motion_loop: End of event 2
[1] [NTC] [EVT] event_new_video FPS 6
[1] [NTC] [ALL] motion_detected: Motion detected - starting event 3

:::: messages.log ::::

Jan  1 00:00:16 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:16 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:16 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Jan  1 00:00:16 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Jan  1 00:00:19 meye-f3da3ba0 daemon.info dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 3
Jan  1 00:00:19 meye-f3da3ba0 daemon.info dhclient: DHCPREQUEST on eth0 to 255.255.255.255 port 67
Jan  1 00:00:19 meye-f3da3ba0 daemon.info dhclient: DHCPOFFER from 192.168.0.1
Jan  1 00:00:19 meye-f3da3ba0 daemon.info dhclient: DHCPACK from 192.168.0.1
Jan  1 00:00:19 meye-f3da3ba0 daemon.info dhclient: bound to 192.168.0.120 -- renewal in 40039 seconds.
Jan  1 00:00:27 meye-f3da3ba0 auth.info sshd[543]: Server listening on 0.0.0.0 port 22.
Oct 30 04:32:44 meye-f3da3ba0 daemon.notice proftpd[565]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Oct 30 04:32:44 meye-f3da3ba0 cron.info crond[572]: crond (busybox 1.23.2) started, log level 8
Oct 30 04:32:45 meye-f3da3ba0 daemon.err nmbd[585]: [2015/10/30 04:32:45.083897,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 30 04:32:45 meye-f3da3ba0 daemon.err nmbd[585]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connections
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]: [2015/10/30 04:32:45.150149,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]: [2015/10/30 04:32:45.177442,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]: [2015/10/30 04:32:45.177946,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]: [2015/10/30 04:32:45.204306,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]: [2015/10/30 04:32:45.204763,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Oct 30 04:32:45 meye-f3da3ba0 daemon.err smbd[582]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 646
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Oct 30 04:32:48 meye-f3da3ba0 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Oct 30 04:32:48 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Oct 30 04:32:50 meye-f3da3ba0 daemon.info init: starting pid 654, tty '': '/sbin/userinit'
Oct 30 04:32:50 meye-f3da3ba0 daemon.info init: starting pid 655, tty '/dev/tty1': '/sbin/getty -L tty1 115200 vt100'
Oct 30 04:32:52 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 2
Oct 30 04:32:52 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
Oct 30 04:33:17 meye-f3da3ba0 daemon.err nmbd[585]: [2015/10/30 04:33:17.005275,  0] ../source3/nmbd/nmbd_become_lmb.c:397(become_local_master_stage2)
Oct 30 04:33:17 meye-f3da3ba0 daemon.err nmbd[585]:   *****
Oct 30 04:33:17 meye-f3da3ba0 daemon.err nmbd[585]:   
Oct 30 04:33:17 meye-f3da3ba0 daemon.err nmbd[585]:   Samba name server MEYE-F3DA3BA0 is now a local master browser for workgroup MOTIONEYE on subnet 192.168.0.120
Oct 30 04:33:17 meye-f3da3ba0 daemon.err nmbd[585]:   
Oct 30 04:33:17 meye-f3da3ba0 daemon.err nmbd[585]:   *****
Oct 30 04:33:36 meye-f3da3ba0 daemon.info proftpd[734]: localhost (192.168.0.119[192.168.0.119]) - FTP session opened.
Oct 30 04:33:36 meye-f3da3ba0 daemon.info proftpd[734]: localhost (192.168.0.119[192.168.0.119]) - FTP session closed.
Oct 30 04:33:36 meye-f3da3ba0 daemon.err smbd[743]: [2015/10/30 04:33:36.587383,  0] ../lib/util/charset/codepoints.c:292(get_conv_handle)
Oct 30 04:33:36 meye-f3da3ba0 daemon.err smbd[743]:   dos charset 'CP850' unavailable - using ASCII
Oct 30 04:33:36 meye-f3da3ba0 auth.info sshd[744]: Did not receive identification string from 192.168.0.119
Oct 30 04:33:49 meye-f3da3ba0 daemon.err smbd[764]: [2015/10/30 04:33:49.391530,  0] ../source3/smbd/process.c:338(read_packet_remainder)
Oct 30 04:33:49 meye-f3da3ba0 daemon.err smbd[764]:   read_fd_with_timeout failed for client 192.168.0.119 read error = NT_STATUS_END_OF_FILE.
Oct 30 04:33:49 meye-f3da3ba0 daemon.err smbd[765]: [2015/10/30 04:33:49.455672,  0] ../lib/util/charset/codepoints.c:292(get_conv_handle)
Oct 30 04:33:49 meye-f3da3ba0 daemon.err smbd[765]:   dos charset 'CP850' unavailable - using ASCII
Oct 30 04:34:00 meye-f3da3ba0 daemon.err smbd[785]: [2015/10/30 04:34:00.611067,  0] ../lib/util/charset/codepoints.c:292(get_conv_handle)
Oct 30 04:34:00 meye-f3da3ba0 daemon.err smbd[785]:   dos charset 'CP850' unavailable - using ASCII
Oct 30 04:34:19 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: End of event 1
Oct 30 04:34:20 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 2
Oct 30 04:34:20 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 2
Oct 30 04:34:51 meye-f3da3ba0 daemon.info init: starting pid 881, tty '/dev/null': '/etc/init.d/rcK'
Oct 29 23:34:51 meye-f3da3ba0 syslog.info syslogd exiting
Dec 31 18:00:02 meye-f3da3ba0 syslog.info syslogd started: BusyBox v1.23.2
Dec 31 18:00:02 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Dec 31 18:00:02 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Dec 31 18:00:02 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Dec 31 18:00:02 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Dec 31 18:00:08 meye-f3da3ba0 auth.info sshd[528]: Server listening on 0.0.0.0 port 22.
Dec 31 18:00:09 meye-f3da3ba0 cron.info crond[550]: crond (busybox 1.23.2) started, log level 8
Dec 31 18:00:09 meye-f3da3ba0 daemon.notice proftpd[543]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Dec 31 18:00:10 meye-f3da3ba0 daemon.err nmbd[571]: [1969/12/31 18:00:10.388740,  0] ../lib/util/become_daemon.c:135(daemon_status)
Dec 31 18:00:10 meye-f3da3ba0 daemon.err nmbd[571]:   STATUS=daemon 'nmbd' : No local IPv4 non-loopback interfaces available, waiting for interface ...NOTE: NetBIOS name resolution is not supported for Internet Protocol Version 6 (IPv6).
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]: [1969/12/31 18:00:10.485876,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]: [1969/12/31 18:00:10.513455,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]: [1969/12/31 18:00:10.513997,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]: [1969/12/31 18:00:10.538379,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]: [1969/12/31 18:00:10.538820,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Dec 31 18:00:10 meye-f3da3ba0 daemon.err smbd[567]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Dec 31 18:00:10 meye-f3da3ba0 daemon.info dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 7
Dec 31 18:00:10 meye-f3da3ba0 daemon.info dhclient: DHCPREQUEST on eth0 to 255.255.255.255 port 67
Dec 31 18:00:10 meye-f3da3ba0 daemon.info dhclient: DHCPOFFER from 192.168.0.1
Dec 31 18:00:10 meye-f3da3ba0 daemon.info dhclient: DHCPACK from 192.168.0.1
Dec 31 18:00:10 meye-f3da3ba0 daemon.info dhclient: bound to 192.168.0.120 -- renewal in 36912 seconds.
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 617
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Dec 31 18:00:12 meye-f3da3ba0 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Dec 31 18:00:12 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Jan  1 00:00:15 meye-f3da3ba0 daemon.info init: starting pid 631, tty '': '/sbin/userinit'
Jan  1 00:00:15 meye-f3da3ba0 daemon.info init: starting pid 632, tty '/dev/tty1': '/sbin/getty -L tty1 115200 vt100'
Dec 31 18:00:15 meye-f3da3ba0 daemon.err nmbd[571]: [1969/12/31 18:00:15.391868,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Dec 31 18:00:15 meye-f3da3ba0 daemon.err nmbd[571]:   STATUS=daemon 'nmbd' finished starting up and ready to serve connections
Dec 31 18:00:19 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 2
Dec 31 18:00:19 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd - Finishing
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Closing
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] motion_web_control: motion-httpd thread exit
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: End of event 1
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_loop: Thread exiting
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] stream_stop: Closing motion-stream listen socket & active motion-stream sockets
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] stream_stop: Closed motion-stream listen socket & active motion-stream sockets
Dec 31 18:01:14 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_close: Closing video device /dev/video0
Dec 31 18:01:16 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Threads finished
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Motion terminating
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 751
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Dec 31 18:01:17 meye-f3da3ba0 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Dec 31 18:01:17 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Dec 31 18:01:24 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [EVT] event_new_video FPS 24
Dec 31 18:01:24 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_detected: Motion detected - starting event 1
Jan  1 00:01:30 meye-f3da3ba0 daemon.info init: starting pid 774, tty '/dev/null': '/etc/init.d/rcK'
Dec 31 18:01:30 meye-f3da3ba0 syslog.info syslogd exiting
Dec 31 18:00:02 meye-f3da3ba0 syslog.info syslogd started: BusyBox v1.23.2
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Dec 31 18:00:26 meye-f3da3ba0 auth.info sshd[642]: Server listening on 0.0.0.0 port 22.
Dec 31 18:00:27 meye-f3da3ba0 daemon.notice proftpd[656]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Dec 31 18:00:27 meye-f3da3ba0 cron.info crond[663]: crond (busybox 1.23.2) started, log level 8
Dec 31 18:00:28 meye-f3da3ba0 daemon.err nmbd[683]: [1969/12/31 18:00:28.287058,  0] ../lib/util/become_daemon.c:135(daemon_status)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err nmbd[683]:   STATUS=daemon 'nmbd' : No local IPv4 non-loopback interfaces available, waiting for interface ...NOTE: NetBIOS name resolution is not supported for Internet Protocol Version 6 (IPv6).
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]: [1969/12/31 18:00:28.392247,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]: [1969/12/31 18:00:28.415362,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]: [1969/12/31 18:00:28.415885,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]: [1969/12/31 18:00:28.439727,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]: [1969/12/31 18:00:28.440280,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[680]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 721
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Dec 31 18:00:30 meye-f3da3ba0 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Jan  1 00:00:33 meye-f3da3ba0 daemon.info init: starting pid 744, tty '': '/sbin/userinit'
Jan  1 00:00:33 meye-f3da3ba0 daemon.info init: starting pid 745, tty '/dev/null': '/etc/init.d/rcK'
Dec 31 18:00:33 meye-f3da3ba0 syslog.info syslogd exiting
Dec 31 18:00:02 meye-f3da3ba0 syslog.info syslogd started: BusyBox v1.23.2
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: /etc/passwd: Read-only file system
Dec 31 18:00:03 meye-f3da3ba0 auth.err passwd: can't update password file /etc/passwd
Dec 31 18:00:26 meye-f3da3ba0 auth.info sshd[645]: Server listening on 0.0.0.0 port 22.
Dec 31 18:00:27 meye-f3da3ba0 cron.info crond[667]: crond (busybox 1.23.2) started, log level 8
Dec 31 18:00:27 meye-f3da3ba0 daemon.notice proftpd[659]: localhost - ProFTPD 1.3.4d (maint) (built Sun Oct 11 2015 21:57:44 EEST) standalone mode STARTUP
Dec 31 18:00:28 meye-f3da3ba0 daemon.err nmbd[686]: [1969/12/31 18:00:28.301999,  0] ../lib/util/become_daemon.c:135(daemon_status)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err nmbd[686]:   STATUS=daemon 'nmbd' : No local IPv4 non-loopback interfaces available, waiting for interface ...NOTE: NetBIOS name resolution is not supported for Internet Protocol Version 6 (IPv6).
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]: [1969/12/31 18:00:28.403159,  0] ../lib/util/become_daemon.c:124(daemon_ready)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]:   STATUS=daemon 'smbd' finished starting up and ready to serve connections
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]: [1969/12/31 18:00:28.429814,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]: [1969/12/31 18:00:28.430378,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]: [1969/12/31 18:00:28.455889,  0] ../source3/lib/util_sock.c:455(open_socket_in)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]:   open_socket_in(): socket() call failed: Address family not supported by protocol
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]: [1969/12/31 18:00:28.456327,  0] ../source3/smbd/server.c:690(smbd_open_one_socket)
Dec 31 18:00:28 meye-f3da3ba0 daemon.err smbd[683]:   smbd_open_once_socket: open_socket_in: Address family not supported by protocol
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] conf_load: Processing thread 0 - config file /data/etc/motion.conf
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] config_thread: Processing config file thread-1.conf
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log level (NTC) (6)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Motion Unofficial-Git-a5b5f13 Started
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Logging to syslog
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using default log type (ALL)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] motion_startup: Using log type (ALL) log level (NTC)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ENC] ffmpeg_init: ffmpeg LIBAVCODEC_BUILD 3680612 LIBAVFORMAT_BUILD 3679332
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is from thread-1.conf
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Thread 1 is device: /dev/video0 input -1
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Stream port 8081
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [ALL] main: Waiting for threads to finish, pid: 724
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Thread 1 started , motion detection Enabled
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using videodevice /dev/video0 and input -1
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability:  ------------------------ cap.driver: "bm2835 mmal" cap.card: "mmal service 16.1" cap.bus_info: "platform:bcm2835-v4l2" cap.capabilities=0x85200005 ------------------------
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_CAPTURE
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - VIDEO_OVERLAY
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - READWRITE
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_get_capability: - STREAMING
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: name = "Camera 0", type 0x00000002, status 00000000
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_select_input: - CAMERA
Dec 31 18:00:30 meye-f3da3ba0 user.warn motion-mrdave: [1] [WRN] [VID] v4l2_select_input: Device doesn't support VIDIOC_G_STD
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd testing : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd Bound : IPV4 addr: 127.0.0.1 port: 7999
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd/Unofficial-Git-a5b5f13 running, accepting connections
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [0] [NTC] [STR] httpd_run: motion-httpd: waiting for data on 127.0.0.1 port TCP 7999
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_do_set_pix_format: Using palette YU12 (320x240) bytesperlines 320 sizeimage 115200 colorspace 00000001
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980900, "Brightness", range 0,100 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Brightness", default 50, current 50
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980901, "Contrast", range -100,100 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Contrast", default 0, current 0
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x00980902, "Saturation", range -100,100 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Saturation", default 0, current 0
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090e, "Red Balance", range 1,7999 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Red Balance", default 1000, current 1000
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls: found control 0x0098090f, "Blue Balance", range 1,7999 
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] v4l2_scan_controls:    "Blue Balance", default 1000, current 1000
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [VID] vid_v4lx_start: Using V4L2
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 1 items
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream testing : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [STR] http_bindsock: motion-stream Bound : IPV4 addr: 0.0.0.0 port: 8081
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] motion_init: Started motion-stream server in port 8081 auth Disabled
Dec 31 18:00:30 meye-f3da3ba0 user.notice motion-mrdave: [1] [NTC] [ALL] image_ring_resize: Resizing pre_capture buffer to 3 items
Jan  1 00:00:33 meye-f3da3ba0 daemon.info init: starting pid 747, tty '': '/sbin/userinit'
Jan  1 00:00:33 meye-f3da3ba0 daemon.info init: starting pid 748, tty '/dev/null': '/etc/init.d/rcK'
Dec 31 18:00:33 meye-f3da3ba0 syslog.info syslogd exiting

:::: dmesg.log ::::

[    0.000000] Booting Linux on physical CPU 0xf00
[    0.000000] Linux version 4.1.10-meye (ccrisan@supermicro) (gcc version 4.8.5 (Buildroot 2015.08-rc1-gb771222) ) #1 SMP PREEMPT Sun Oct 11 22:17:48 EEST 2015
[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: BCM2709
[    0.000000] cma: Reserved 8 MiB at 0x36800000
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] On node 0 totalpages: 225280
[    0.000000] free_area_init_node: node 0, pgdat 8058a300, node_mem_map b6112000
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 225280 pages, LIFO batch:31
[    0.000000] [bcm2709_smp_init_cpus] enter (93c0->f3003010)
[    0.000000] [bcm2709_smp_init_cpus] ncores=4
[    0.000000] PERCPU: Embedded 10 pages/cpu @b60e5000 s11136 r8192 d21632 u40960
[    0.000000] pcpu-alloc: s11136 r8192 d21632 u40960 alloc=10*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 223520
[    0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=656 bcm2708_fb.fbheight=416 bcm2709.boardrev=0xa01041 bcm2709.serial=0xf3da3ba0 smsc95xx.macaddr=B8:27:EB:DA:3B:A0 bcm2708_fb.fbswap=1 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000  dwc_otg.fiq_fix_enable=1 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 rootwait ro rootflags=noload
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 878848K/901120K available (4003K kernel code, 235K rwdata, 1228K rodata, 172K init, 359K bss, 14080K reserved, 8192K cma-reserved)
[    0.000000] Virtual kernel memory layout:
                   vector  : 0xffff0000 - 0xffff1000   (   4 kB)
                   fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
                   vmalloc : 0xb7800000 - 0xff000000   (1144 MB)
                   lowmem  : 0x80000000 - 0xb7000000   ( 880 MB)
                   modules : 0x7f000000 - 0x80000000   (  16 MB)
                     .text : 0x80008000 - 0x80524034   (5233 kB)
                     .init : 0x80525000 - 0x80550000   ( 172 kB)
                     .data : 0x80550000 - 0x8058af88   ( 236 kB)
                      .bss : 0x8058d000 - 0x805e6ee4   ( 360 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:608
[    0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
[    0.000000] clocksource arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000014] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000032] Switching to timer-based delay loop, resolution 52ns
[    0.000226] Console: colour dummy device 80x30
[    0.001482] console [tty1] enabled
[    0.001538] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=19200)
[    0.001629] pid_max: default: 32768 minimum: 301
[    0.001811] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.001867] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002920] CPU: Testing write buffer coherency: ok
[    0.003460] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
[    0.003520] [bcm2709_smp_prepare_cpus] enter
[    0.003650] Setting up static identity map for 0x8240 - 0x8274
[    0.009605] [bcm2709_boot_secondary] cpu:1 started (0) 17
[    0.009980] [bcm2709_secondary_init] enter cpu:1
[    0.010027] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
[    0.011572] [bcm2709_boot_secondary] cpu:2 started (0) 16
[    0.011862] [bcm2709_secondary_init] enter cpu:2
[    0.011892] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
[    0.013620] [bcm2709_boot_secondary] cpu:3 started (0) 17
[    0.013875] [bcm2709_secondary_init] enter cpu:3
[    0.013904] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
[    0.013975] Brought up 4 CPUs
[    0.014097] SMP: Total of 4 processors activated (153.60 BogoMIPS).
[    0.014143] CPU: All CPU(s) started in SVC mode.
[    0.014896] devtmpfs: initialized
[    0.033105] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
[    0.033463] clocksource jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.034744] NET: Registered protocol family 16
[    0.040564] DMA: preallocated 4096 KiB pool for atomic coherent allocations
[    0.041875] bcm2709.uart_clock = 3000000
[    0.043430] Serial: AMBA PL011 UART driver
[    0.043581] dev:f1: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev3
[    0.044101] bcm2835-mbox bcm2835-mbox: mailbox enabled
[    0.087436] bcm2708-dmaengine bcm2708-dmaengine: DMA legacy API manager at f3007000, dmachans=0x7f35
[    0.087550] bcm2708-dmaengine bcm2708-dmaengine: failed to get irq for DMA channel 13
[    0.087629] bcm2708-dmaengine bcm2708-dmaengine: Initialized 8 DMA channels (+ 1 legacy)
[    0.088447] bcm2708-dmaengine bcm2708-dmaengine: Load BCM2835 DMA engine driver
[    0.088527] bcm2708-dmaengine bcm2708-dmaengine: dma_debug:0
[    0.088917] usbcore: registered new interface driver usbfs
[    0.089046] usbcore: registered new interface driver hub
[    0.089205] usbcore: registered new device driver usb
[    0.089382] media: Linux media interface: v0.10
[    0.089504] Linux video capture interface: v2.00
[    0.090062] raspberrypi-firmware raspberrypi-firmware.0: Attached to firmware from 2015-09-23 12:21
[    0.115984] Advanced Linux Sound Architecture Driver Initialized.
[    0.117409] Switched to clocksource arch_sys_counter
[    0.117937] FS-Cache: Loaded
[    0.118200] CacheFiles: Loaded
[    0.128325] NET: Registered protocol family 2
[    0.129504] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.129686] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.129916] TCP: Hash tables configured (established 8192 bind 8192)
[    0.130068] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.130169] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.130552] NET: Registered protocol family 1
[    0.131656] bcm2708_gpio: bcm2708_gpio_probe 80572ac8
[    0.133300] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    0.144769] FS-Cache: Netfs 'cifs' registered for caching
[    0.145285] Key type cifs.spnego registered
[    0.147377] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[    0.147496] io scheduler noop registered
[    0.147549] io scheduler deadline registered
[    0.147635] io scheduler cfq registered (default)
[    0.148960] BCM2708FB: allocated DMA memory f6c00000
[    0.149041] BCM2708FB: allocated DMA channel 0 @ f3007000
[    0.154625] Console: switching to colour frame buffer device 82x26
[    0.160674] bcm2708_rng_init=b7806000
[    1.091202] vc-cma: Videocore CMA driver
[    1.093121] vc-cma: vc_cma_base      = 0x00000000
[    1.094998] vc-cma: vc_cma_size      = 0x00000000 (0 MiB)
[    1.096837] vc-cma: vc_cma_initial   = 0x00000000 (0 MiB)
[    1.098876] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
[    1.115640] brd: module loaded
[    1.118367] vchiq: vchiq_init_state: slot_zero = 0xb6c80000, is_master = 0
[    1.122121] usbcore: registered new interface driver smsc95xx
[    1.124132] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
[    1.326301] Core Release: 2.80a
[    1.328168] Setting default values for core params
[    1.330052] Finished setting default values for core params
[    1.532291] Using Buffer DMA mode
[    1.534123] Periodic Transfer Interrupt Enhancement - disabled
[    1.535985] Multiprocessor Interrupt Enhancement - disabled
[    1.537846] OTG VER PARAM: 0, OTG VER FLAG: 0
[    1.539668] Dedicated Tx FIFOs mode
[    1.541725] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xb6c14000 dma = 0xf6c14000 len=9024
[    1.545437] FIQ FSM acceleration enabled for :
               Non-periodic Split Transactions
               Periodic Split Transactions
               High-Speed Isochronous Endpoints
[    1.552899] dwc_otg: Microframe scheduler enabled
[    1.552973] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x802bc8a4
[    1.554853] WARN::hcd_init_fiq:413: FIQ ASM at 0x802bcc04 length 36
[    1.556727] WARN::hcd_init_fiq:438: MPHI regs_base at 0xb7898000
[    1.558611] dwc_otg bcm2708_usb: DWC OTG Controller
[    1.560573] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
[    1.562618] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
[    1.564621] Init: Port Power? op_state=1
[    1.566514] Init: Power Port (0)
[    1.568627] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.570574] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.572491] usb usb1: Product: DWC OTG Controller
[    1.574374] usb usb1: Manufacturer: Linux 4.1.10-meye dwc_otg_hcd
[    1.576269] usb usb1: SerialNumber: bcm2708_usb
[    1.578958] hub 1-0:1.0: USB hub found
[    1.580858] hub 1-0:1.0: 1 port detected
[    1.583050] dwc_otg: FIQ enabled
[    1.583062] dwc_otg: NAK holdoff enabled
[    1.583072] dwc_otg: FIQ split-transaction FSM enabled
[    1.583105] Module dwc_common_port init
[    1.583441] usbcore: registered new interface driver uvcvideo
[    1.585275] USB Video Class driver (1.1.1)
[    1.587668] bcm2708 watchdog, heartbeat=10 sec (nowayout=0)
[    1.589793] bcm2835-cpufreq: min=600000 max=900000
[    1.594611] sdhci: Secure Digital Host Controller Interface driver
[    1.595837] sdhci: Copyright(c) Pierre Ossman
[    1.597198] mmc-bcm2835 mmc-bcm2835.0: mmc_debug:0 mmc_debug2:0
[    1.598407] mmc-bcm2835 mmc-bcm2835.0: DMA channels allocated
[    1.621598] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.624181] hidraw: raw HID events driver (C) Jiri Kosina
[    1.625715] usbcore: registered new interface driver usbhid
[    1.626945] usbhid: USB HID core driver
[    1.628664] ip_tables: (C) 2000-2006 Netfilter Core Team
[    1.630181] NET: Registered protocol family 17
[    1.631516] Key type dns_resolver registered
[    1.634213] Registering SWP/SWPB emulation handler
[    1.640300] vc-sm: Videocore shared memory driver
[    1.641581] [vc_sm_connected_init]: start
[    1.643304] [vc_sm_connected_init]: end - returning 0
[    1.646351] ALSA device list:
[    1.647649]   #0: bcm2835 ALSA
[    1.649088] Waiting for root device /dev/mmcblk0p2...
[    1.668864] mmc0: host does not support reading read-only switch, assuming write-enable
[    1.673422] mmc0: new high speed SDHC card at address 59b4
[    1.674997] mmcblk0: mmc0:59b4 00000 14.9 GiB 
[    1.677418]  mmcblk0: p1 p2 p3
[    1.755465] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: noload
[    1.758018] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
[    1.760172] devtmpfs: mounted
[    1.761675] Freeing unused kernel memory: 172K (80525000 - 80550000)
[    1.782495] Indeed it is in host mode hprt0 = 00021501
[    1.913135] EXT4-fs (mmcblk0p3): couldn't mount as ext2 due to feature incompatibilities
[    1.945429] usb 1-1: new high-speed USB device number 2 using dwc_otg
[    1.947030] Indeed it is in host mode hprt0 = 00001101
[    1.988605] EXT4-fs (mmcblk0p3): recovery complete
[    1.994149] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[    2.121748] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
[    2.123550] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.125822] hub 1-1:1.0: USB hub found
[    2.127452] hub 1-1:1.0: 5 ports detected
[    2.164295] bcm2835-v4l2: scene mode selected 0, was 0
[    2.164630] bcm2835-v4l2: V4L2 device registered as video0 - stills mode > 2592x1944
[    2.172415] bcm2835-v4l2: Broadcom 2835 MMAL video capture ver 0.0.2 loaded.
[    2.344161] udevd[100]: starting version 3.1.2
[    2.364339] random: udevd urandom read with 65 bits of entropy available
[    2.382047] udevd[100]: specified group 'input' unknown
[    2.402431] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
[    2.490006] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
[    2.490300] bcm2708_i2c_init_pinmode(1,2)
[    2.490305] bcm2708_i2c_init_pinmode(1,3)
[    2.490549] bcm2708_i2c bcm2708_i2c.1: BSC1 Controller at 0x3f804000 (irq 79) (baudrate 100000)
[    2.500953] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    2.504824] bcm2708_spi bcm2708_spi.0: master is unqueued, this is deprecated
[    2.507656] bcm2708_spi bcm2708_spi.0: SPI Controller at 0x3f204000 (irq 80)
[    2.510196] smsc95xx v1.0.4
[    2.559776] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:da:3b:a0
[    8.397180] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
[   10.040500] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC5E1
[   11.207150] random: nonblocking pool is initialized
[   67.098470] bcm2835-v4l2: error 0 waiting for frame completion
[  100.568479] usb 1-1.3: new high-speed USB device number 4 using dwc_otg
[  100.655216] usb 1-1.3: New USB device found, idVendor=7392, idProduct=7811
[  100.656431] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  100.657566] usb 1-1.3: Product: 802.11n WLAN Adapter
[  100.658708] usb 1-1.3: Manufacturer: Realtek
[  100.659889] usb 1-1.3: SerialNumber: 00e04c000001
[  100.879126] usbcore: registered new interface driver rtl8192cu

:::: boot.log ::::

---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
/dev/mmcblk0p3: Bad magic number in super-block while opening filesystem
Formatting data partition
Discarding device blocks:    4096/3859968���������������               ���������������done                            
Creating filesystem with 3859968 4k blocks and 966656 inodes
Filesystem UUID: 141d4cf7-0253-422f-82e0-c7a0e1bee29e
Superblock backups stored on blocks: 
    32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208

Allocating group tables:   0/118�������       �������done                            
Writing inode tables:   0/118�������       �������done                            
Creating journal (32768 blocks): done
Writing superblocks and filesystem accounting information:   0/118������� 10/118�������       �������done

Setting empty admin password
Starting network: wlan0: no device
eth0: starting dhclient
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet 192.168.0.120  netmask 255.255.255.0  broadcast 192.168.0.255
        ether b8:27:eb:da:3b:a0  txqueuelen 1000  (Ethernet)
        RX packets 5  bytes 1296 (1.2 KiB)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 2  bytes 700 (700.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
ssh-keygen: generating new host keys: RSA1 RSA DSA ECDSA ED25519 
Starting sshd: done
Setting current date using http: Fri Oct 30 04:32:44 UTC 2015
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting motioneye: done
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down motioneye: done
---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
Setting custom root/admin password
Starting wpa_supplicant: no device
Starting network: wlan0: no device
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:da:3b:a0  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
Starting sshd: done
Setting current date using http: failed
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting motioneye: done
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down motioneye: done
---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
Setting custom root/admin password
Starting wpa_supplicant: failed
Starting network: wlan0: no link
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:da:3b:a0  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 00:0f:60:06:aa:98  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
Starting sshd: done
Setting current date using http: failed
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting motioneye: done
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down motioneye: done
---- booting ----
Setting hostname: done
Starting logging: done
Starting watchdog: done
Starting eudev: done
Setting up data partition
Setting custom root/admin password
Starting wpa_supplicant: failed
Starting network: wlan0: no link
eth0: flags=4098<BROADCAST,MULTICAST>  mtu 1500
        ether b8:27:eb:da:3b:a0  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        loop  txqueuelen 0  (Local Loopback)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

wlan0: flags=4099<UP,BROADCAST,MULTICAST>  mtu 1500
        ether 00:0f:60:06:aa:98  txqueuelen 1000  (Ethernet)
        RX packets 0  bytes 0 (0.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 0  bytes 0 (0.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

done
Starting sshd: done
Setting current date using http: failed
Starting http date updater: done
Starting proftpd: done
Starting crond: done
Setting smb admin password: done
Starting smbd: done
Starting nmbd: done
Starting motioneye: done
---- shutting down ----
Stopping logging: done
Stopping watchdog: done
Stopping eudev: done
Shutting down wpa_supplicant: done
Stopping network: done
Stopping sshd: done
Shutting down date updater: done
Stopping proftpd: done
Stopping crond: done
Shutting down smbd: done
Shutting down nmbd: done
Shutting down motioneye: done

How do I get the Web Hook notification to post an image?

Note: even though I choose POST it always switches back to GET.

Here's what I see:

http://requestb.in
GET /url
0 bytes 12s ago
From
FORM/POST PARAMETERS

None
HEADERS

Accept-Encoding: identity
Via: 1.1 vegur
Total-Route-Time: 0
Host: requestb.in
X-Request-Id: d85565e8-186e-4300-a94e-5175e8c32f77
Connect-Time: 1
User-Agent: Python-urllib/2.7
Connection: close
RAW BODY

None

How to Update

Hi, I have the first pre-release installed, is there an easy way to update it, or do I need to re-image?

Regards

Damian

Raspberry PI USB WiFi dongle not supported

Hi,

I'm getting an error running on a Raspberry Pi 2 Model B with the official WiFi dongle - https://www.raspberrypi.org/products/usb-wifi-dongle/
Error:

usb 1-1.3: Direct firmware load for brcm/brcmfmac43143.bin failed with error -2

It seems that the firmware is not there.

I tested on Raspbian and it works fine. The firmware is at /lib/firmware/brcm/

Can you help on this?

Thanks for the brilliant work, well done!

Arthur

Working Great

Sorry but couldnt find anywhere else to leave this message.
Downloaded and installed on my raspberry pi 2. Ive had a RTSP network camera and so ive been using a standard fork (mr dave) of motion and running it manually.
Your interface is excellent, its working great with my rtsp camera.
Great work.

request for rsync

Great distro, working really great for me :)

I'd really like to configure rsync as a post-motion command but I can't see rsync in the build.

Could rsync be included? Or is there an alternative approach to pushing files up online?

Thanks

No image in email

Hi

Firsty I just sent you a new log, upgrade went fine and I get email notifications, but no image.

Regards

Damian

Odroid C1 latest version: 20151103 not for Odroid, for RPi???

Please check the latest version: 20151103 for Odroid C1, it appears to be for the RPi. The image does not work with an Odroid C1.

Thanks,
F Mitchell

Setting up WiFi with MotionEye

bootlog.txt
dmesglog.txt
messageslog.txt

motionlog.txt

Hello Calin, I have upgraded to the new OS and having some issues setting up my system using WiFi. I can get everything loaded using a direct Ethernet connection and I change all the settings to use the correct WiFi SSID but cannot find the correct login. I tried to change the /data/etc/wpa_supplicant.conf file to the SSID i use on other applications, cannot find the system. I am enclosing all the log files associated with this project, hopefully you will be able to tell me the error of my ways.
Thank,
Danny
PS Trying to remane the files as .txt to send them here.

Motion not recording

Hi there

Thanks very much for an A1 pieced of code, VERY impressive. I have all installed, however, when I tried to install ffmpeg I get the error:

Package ffmpeg is not available, but is referred to by another package.
This may mean that the package is missing, has been obsoleted, or
is only available from another source

E: Package 'ffmpeg' has no installation candidate

This is installing on the latest Raspian.

Another thing is, that although I can see the camera border turn red, no files are being written to the folder. Can anyone help? Also, is it possible to create sub folders for each camera and then for year\month\day within that folder?

Do you have any time frame for dropbox integration? Will you be also looking at box.com?

Thanks again, and sorry if these are silly questions

Stuart

Multi cams, Philips pc 900 crash after few minutes

I have a Raspberry PI 2 model B with a Raspberry Pi camera module (black) and a Philips pc 900 (USB).
Philips pc 900 crash after 30 minutes and seems busy when motioneyeos tries to restart it.

Here is my log files
http://pastebin.com/kkrLxbuZ (motion.log)
http://pastebin.com/GsWzR248 (motioneye.log)
http://pastebin.com/DSLU8kMX (messages.log)
http://pastebin.com/eWEEkiuW (dmesg.log)

The interesting parts seems to be:

The crash log I presume.

[2] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device
[2] [NTC] [VID] vid_close: Closing video device /dev/v4l/by-id/usb-0471_0329_01690000CE000000-video-index0

And the unsuccessful automatique restart.

[2] [NTC] [VID] v4l2_do_set_pix_format: Testing palette YU12 (320x240)
[2] [ERR] [VID] v4l2_do_set_pix_format: Error setting pixel format.
VIDIOC_S_FMT: : Device or resource busy
[2] [ERR] [VID] VIDIOC_TRY_FMT failed for format v4l2_set_pix_format: Device or resource busy
[2] [ERR] [VID] v4l2_set_pix_format: Unable to find a compatible palette format.
[2] [NTC] [VID] vid_v4lx_start: Using V4L1
[2] [ERR] [ALL] motion_loop: Video device fatal error - Closing video device

No email notifications after installing motioneyeOS

I've just installed the new version, and motion detection and image and video capture are working fine, however no emails are being sent.

I've got it set to use gmail to send the images, and it is set up exactly as it was with the previous version, but it seems there's no attempt for the emails to be sent. I can't see anything in the logs that shows any attempt, or any issues with sending the emails.

Link to logs: https://www.dropbox.com/s/y33mtwfpj8ibu38/motioneye.zip?dl=0

cannot add a camera

hello, my rpi cam was not connected properly when i installed motioneyeos.
now i cannot add or remove a camera.
here are the logs : https://dl.dropboxusercontent.com/u/18722948/motioneye.log

thanks

Intermittently web server stops responding

I set up a couple USB cameras on my Raspberry Pi 2, and then went out of town. It worked great for a day or so. Then out of nowhere the website stopped responding.

I can still get to the raw MJPEG streams, but the website no longer functions and motion is not running either (I can tell because I stopped getting notifications).

I cannot fix anything now because I'm out of town and did not set up SSH access (mainly because the web UI does not allow you to customize the SSH port).

When I get back into town, is there a particular log that will help you troubleshoot this?

Setting Up Email Object and Text

Hello and Thanks so much for your great work !!!
Is there a way to modify email template such as Object and body text ?

Support for SSL?

Does motionEyeOS have support for SSL? When logging in remotely, my credentials are sent in plain text.

Cannot write: No space left on device

Hi,

I cannot rebuild image.

Thanks.

$ ./build.sh raspberrypi2        
>>>   Finalizing target directory
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/lib/luarocks
mkdir -p /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc
echo "primcam.ru" > /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/issue
mkdir -p /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/network/
( echo "# interface file auto-generated by buildroot"; echo ; echo "auto lo"; echo "iface lo inet loopback"; ) > /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/network/interfaces
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/include /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/aclocal \
    /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/lib/pkgconfig /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/pkgconfig \
    /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/lib/cmake /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/cmake
find /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/{lib,share}/ -name '*.cmake' -print0 | xargs -0 rm -f
find /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/lib \( -name '*.a' -o -name '*.la' \) -print0 | xargs -0 rm -f
find /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/lib \( -name '*.a' -o -name '*.la' \) -print0 | xargs -0 rm -f
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/gdb
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/zsh
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/man /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/man
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/info /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/info
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/doc /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/doc
rm -rf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/gtk-doc
rmdir /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share 2>/dev/null
Makefile:560: recipe for target 'target-finalize' failed
make[1]: [target-finalize] Error 1 (ignored)
find /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target -type f \( -perm /111 -o -name '*.so*' \) -not \( -name 'libpthread*.so*' -o -name '*.ko' \) -print0 | xargs -0 /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/arm-buildroot-linux-gnueabihf-strip --remove-section=.comment --remove-section=.note 2>/dev/null || true
if test -d /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/lib/modules; then \
    find /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/lib/modules -type f -name '*.ko' -print0 | \
    xargs -0 -r /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/arm-buildroot-linux-gnueabihf-strip --remove-section=.comment --remove-section=.note --strip-unneeded; fi
find /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/lib -type f -name 'libpthread*.so*' | \
    xargs -r /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/arm-buildroot-linux-gnueabihf-strip --remove-section=.comment --remove-section=.note --strip-debug
mkdir -p /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc
# Mandatory configuration file and auxiliary cache directory
# for recent versions of ldconfig
touch /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/ld.so.conf
mkdir -p /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/var/cache/ldconfig
if [ -x "/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/arm-buildroot-linux-gnueabihf-ldconfig" ]; \
then \
    /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/arm-buildroot-linux-gnueabihf-ldconfig -r /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target \
                -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/ld.so.conf; \
else \
    /sbin/ldconfig -r /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target \
               -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/ld.so.conf; \
fi
/sbin/ldconfig.real: Warning: ignoring configuration file that cannot be opened: /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/ld.so.conf: No such file or directory
/sbin/ldconfig.real: /usr/lib/libstdc++.so.6.0.19-gdb.py is not an ELF file - it has the wrong magic bytes at the start.

( \
    echo "NAME=Buildroot"; \
    echo "VERSION=2015.08-rc1-gb771222"; \
    echo "ID=buildroot"; \
    echo "VERSION_ID=2015.08-rc1"; \
    echo "PRETTY_NAME=\"Buildroot 2015.08-rc1\"" \
) >  /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/etc/os-release
>>>   Copying overlay board/common/overlay
>>>   Copying overlay board/raspberrypi2/overlay
>>>   Executing post-build script board/common/postscript.sh
rm: cannot remove ‘/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/usr/share/perl5’: Is a directory
>>>   Generating root filesystem image rootfs.ext2
rm -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
rm -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/THIS_IS_NOT_YOUR_ROOT_FILESYSTEM
rm -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_users_table.txt
echo "set -e" >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
echo "chown -h -R 0:0 /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target" >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
cat system/device_table.txt > /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_device_table.txt
printf '    /bin/busybox                     f 4755 0  0 - - - - -\n    /var/lib/nginx d 755 33 33 - - - - -\n /dev/console c 622 0 0 5 1 - - -\n' >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_device_table.txt
#echo "/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/makedevs -d /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_device_table.txt /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target" >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
printf '    - - input -1 * - - - Input device group\n   sshd -1 sshd -1 * - - - SSH drop priv user\n' >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_users_table.txt
#PATH="/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/sbin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/sbin:/usr/local/heroku/bin:/home/csolg/.rvm/gems/ruby-2.2.3/bin:/home/csolg/.rvm/gems/ruby-2.2.3@global/bin:/home/csolg/.rvm/rubies/ruby-2.2.3/bin:/usr/local/heroku/bin:/home/csolg/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.rvm/bin:/home/csolg/.rvm/bin:/home/csolg/mobile/platforms/android/sdk/tools:/home/csolg/mobile/platforms/android/sdk/platform-tools:/home/csolg/bin:/usr/lib/lightdm/lightdm:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.local/bin:/home/csolg/.rvm/bin" /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/support/scripts/mkusers /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_users_table.txt /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
echo "  PATH="/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/sbin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/sbin:/usr/local/heroku/bin:/home/csolg/.rvm/gems/ruby-2.2.3/bin:/home/csolg/.rvm/gems/ruby-2.2.3@global/bin:/home/csolg/.rvm/rubies/ruby-2.2.3/bin:/usr/local/heroku/bin:/home/csolg/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.rvm/bin:/home/csolg/.rvm/bin:/home/csolg/mobile/platforms/android/sdk/tools:/home/csolg/mobile/platforms/android/sdk/platform-tools:/home/csolg/bin:/usr/lib/lightdm/lightdm:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.local/bin:/home/csolg/.rvm/bin" mke2img -d /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target -G 4 -R 1 -o /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/images/rootfs.ext2" >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
chmod a+x /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
PATH="/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/sbin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/sbin:/usr/local/heroku/bin:/home/csolg/.rvm/gems/ruby-2.2.3/bin:/home/csolg/.rvm/gems/ruby-2.2.3@global/bin:/home/csolg/.rvm/rubies/ruby-2.2.3/bin:/usr/local/heroku/bin:/home/csolg/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.rvm/bin:/home/csolg/.rvm/bin:/home/csolg/mobile/platforms/android/sdk/tools:/home/csolg/mobile/platforms/android/sdk/platform-tools:/home/csolg/bin:/usr/lib/lightdm/lightdm:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.local/bin:/home/csolg/.rvm/bin" /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/fakeroot -- /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
tune2fs 1.42.13 (17-May-2015)
tune2fs 1.42.13 (17-May-2015)

Please run e2fsck on the filesystem.

Creating journal inode: done
This filesystem will be automatically checked every 20 mounts or
0 days, whichever comes first.  Use tune2fs -c or -i to override.

mke2img: e2fsck was successfully run on '/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/images/rootfs.ext2' (ext4)

tune2fs 1.42.13 (17-May-2015)
Setting maximal mount count to -1
Setting interval between checks to 0 seconds
/usr/bin/install -m 0644 support/misc/target-dir-warning.txt /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/THIS_IS_NOT_YOUR_ROOT_FILESYSTEM
ln -sf rootfs.ext2 /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/images/rootfs.ext4
>>>   Generating root filesystem image rootfs.tar
rm -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
rm -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/THIS_IS_NOT_YOUR_ROOT_FILESYSTEM
rm -f /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_users_table.txt
echo "set -e" >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
echo "chown -h -R 0:0 /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target" >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
cat system/device_table.txt > /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_device_table.txt
printf '    /bin/busybox                     f 4755 0  0 - - - - -\n    /var/lib/nginx d 755 33 33 - - - - -\n /dev/console c 622 0 0 5 1 - - -\n' >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_device_table.txt
#echo "/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/makedevs -d /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_device_table.txt /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target" >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
printf '    - - input -1 * - - - Input device group\n   sshd -1 sshd -1 * - - - SSH drop priv user\n' >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_users_table.txt
#PATH="/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/sbin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/sbin:/usr/local/heroku/bin:/home/csolg/.rvm/gems/ruby-2.2.3/bin:/home/csolg/.rvm/gems/ruby-2.2.3@global/bin:/home/csolg/.rvm/rubies/ruby-2.2.3/bin:/usr/local/heroku/bin:/home/csolg/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.rvm/bin:/home/csolg/.rvm/bin:/home/csolg/mobile/platforms/android/sdk/tools:/home/csolg/mobile/platforms/android/sdk/platform-tools:/home/csolg/bin:/usr/lib/lightdm/lightdm:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.local/bin:/home/csolg/.rvm/bin" /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/support/scripts/mkusers /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_users_table.txt /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
echo "  tar -cf /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/images/rootfs.tar --numeric-owner -C /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target ." >> /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
chmod a+x /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
PATH="/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/sbin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/sbin:/usr/local/heroku/bin:/home/csolg/.rvm/gems/ruby-2.2.3/bin:/home/csolg/.rvm/gems/ruby-2.2.3@global/bin:/home/csolg/.rvm/rubies/ruby-2.2.3/bin:/usr/local/heroku/bin:/home/csolg/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.rvm/bin:/home/csolg/.rvm/bin:/home/csolg/mobile/platforms/android/sdk/tools:/home/csolg/mobile/platforms/android/sdk/platform-tools:/home/csolg/bin:/usr/lib/lightdm/lightdm:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.local/bin:/home/csolg/.rvm/bin" /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin/fakeroot -- /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/build/_fakeroot.fs
/usr/bin/install -m 0644 support/misc/target-dir-warning.txt /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/target/THIS_IS_NOT_YOUR_ROOT_FILESYSTEM
PATH="/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/sbin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/bin:/home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/host/usr/sbin:/usr/local/heroku/bin:/home/csolg/.rvm/gems/ruby-2.2.3/bin:/home/csolg/.rvm/gems/ruby-2.2.3@global/bin:/home/csolg/.rvm/rubies/ruby-2.2.3/bin:/usr/local/heroku/bin:/home/csolg/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.rvm/bin:/home/csolg/.rvm/bin:/home/csolg/mobile/platforms/android/sdk/tools:/home/csolg/mobile/platforms/android/sdk/platform-tools:/home/csolg/bin:/usr/lib/lightdm/lightdm:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games:/usr/local/games:/home/csolg/.local/bin:/home/csolg/.rvm/bin" xz -9 -C crc32 -c /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/images/rootfs.tar > /home/old/csolg/Downloads/linux/motioneyeos/motioneyeos/output/raspberrypi2/images/rootfs.tar.xz
:: creating boot loop device
20+0 records in
20+0 records out
20971520 bytes (21 MB) copied, 0,0431057 s, 487 MB/s
:: creating boot filesystem
mkfs.fat 3.0.28 (2015-05-16)
Loop device does not match a floppy size, using default hd params
:: mounting boot loop device
:: copying boot filesystem contents
:: unmounting boot filesystem
:: destroying boot loop device
:: creating root loop device
180+0 records in
180+0 records out
188743680 bytes (189 MB) copied, 1,49084 s, 127 MB/s
:: creating root filesystem
mke2fs 1.42.12 (29-Aug-2014)
Discarding device blocks: done                            
Creating filesystem with 184320 1k blocks and 46184 inodes
Filesystem UUID: 2d8de536-66bf-44a6-9ff4-00fedbe7ada2
Superblock backups stored on blocks: 
    8193, 24577, 40961, 57345, 73729

Allocating group tables: done                            
Writing inode tables: done                            
Creating journal (4096 blocks): done
Writing superblocks and filesystem accounting information: done 

tune2fs 1.42.12 (29-Aug-2014)
:: mounting root loop device
:: copying root filesystem contents
tar: ./lib/modules/4.1.10-meye/kernel/sound/core/seq/snd-seq.ko: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/sound/core/seq/snd-seq-midi.ko: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/sound/core/seq/snd-seq-midi-event.ko: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/sound/core/snd-hrtimer.ko: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/sound/core/snd-hwdep.ko: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/sound/usb/snd-usbmidi-lib.ko: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/sound/usb/snd-usb-audio.ko: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/lib: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/lib: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/lib/zlib_deflate: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/lib: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/lib/zlib_deflate/zlib_deflate.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/lib: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/lib/crc-ccitt.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/fs: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/fs: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/fs/ext3: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/fs: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/fs/ext3/ext3.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/fs: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/fs/jbd: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/fs: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/fs/jbd/jbd.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/fs: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/fs/fuse: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/fs: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/fs/fuse/fuse.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/bsd_comp.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/pppoe.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/pppox.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/ppp_mppe.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/ppp_async.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/ppp_generic.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/ppp_synctty.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/ppp/ppp_deflate.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/phy: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/phy/libphy.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/tun.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/slip: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/slip/slhc.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/zd1201.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/mediatek: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/mediatek/mt7601u: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/mediatek/mt7601u/mt7601u.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rsi: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rsi/rsi_91x.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rsi/rsi_usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/libertas: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/libertas/libertas.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/libertas/usb8xxx.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rt2x00: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rt2x00/rt2800usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rt2x00/rt2800lib.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rt2x00/rt73usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rt2x00/rt2x00lib.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rt2x00/rt2500usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rt2x00/rt2x00usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/zd1211rw: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/zd1211rw/zd1211rw.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/carl9170: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/carl9170/carl9170.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath10k: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath10k/ath10k_core.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ar5523: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ar5523/ar5523.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/wcn36xx: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/wcn36xx/wcn36xx.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath9k: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath9k/ath9k_hw.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath9k/ath9k_common.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath9k/ath9k_htc.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath9k/ath9k.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath6kl: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath6kl/ath6kl_core.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/ath/ath6kl/ath6kl_usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/brcm80211: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/brcm80211/brcmutil: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/brcm80211/brcmutil/brcmutil.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/brcm80211/brcmfmac: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/brcm80211/brcmfmac/brcmfmac.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rtl8192cu: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rtl8192cu/8192cu.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rndis_wlan.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/hostap: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/hostap/hostap.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/b43: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/b43/b43.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rtl818x: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rtl818x/rtl8187: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/rtl818x/rtl8187/rtl8187.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/b43legacy: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/b43legacy/b43legacy.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/mwifiex: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/mwifiex/mwifiex_usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/mwifiex/mwifiex.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/libertas_tf: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/libertas_tf/libertas_tf.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/libertas_tf/libertas_tf_usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/at76c50x-usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/p54: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/p54/p54common.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/wireless/p54/p54usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/cdc_ncm.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/hso.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/sr9700.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/smsc75xx.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/int51x1.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/asix.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/mcs7830.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/cdc_eem.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/cdc_ether.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/pegasus.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/rtl8150.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/r8152.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/sr9800.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/cdc_mbim.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/ipheth.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/kaweth.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/rndis_host.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/dm9601.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/ax88179_178a.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/net/usb/catc.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/ssb: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/ssb/ssb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/v4l2-core: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/v4l2-core/videobuf-core.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/v4l2-core/videobuf-vmalloc.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/v4l2-core/tuner.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/dvb-frontends: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/dvb-frontends/af9013.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/dvb-frontends/as102_fe.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/dvb-frontends/af9033.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/dvb-frontends/zl10353.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/dvb-frontends/ec100.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common/cypress_firmware.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common/tveeprom.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common/siano: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common/siano/smsdvb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common/siano/smsmdtv.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common/b2c2: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/common/b2c2/b2c2-flexcop.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/platform: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/platform/bcm2835: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/platform/bcm2835/bcm2835-v4l2.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/platform/soc_camera: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/platform/soc_camera/soc_camera.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/platform/soc_camera/soc_mediabus.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/ov7670.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/mt9v011.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/vs6624.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/sr030pc30.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/ov7640.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/ov9740.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/tw9910.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/mt9t031.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/ov5642.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/rj54n1cb0c.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/ov6650.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/mt9m001.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/ov9640.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/ov2640.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/mt9m111.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/ov772x.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/imx074.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/mt9t112.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/i2c/soc_camera/mt9v022.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_vc032x.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_spca1528.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_t613.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_zc3xx.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/m5602: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/m5602/gspca_m5602.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_spca561.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_pac207.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_mars.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_stk1135.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_spca508.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_benq.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_se401.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sunplus.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_conex.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_finepix.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_cpia1.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sq930x.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_konica.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_xirlink_cit.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_ov519.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_touptek.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_ov534.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gl860: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gl860/gspca_gl860.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_mr97310a.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_etoms.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sonixj.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_spca501.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_spca506.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_pac7311.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_topro.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_stv0680.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_tv8532.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_nw80x.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sq905c.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_spca500.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_vicam.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sn9c20x.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sonixb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_kinect.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sq905.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_pac7302.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_jl2005bcd.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_stk014.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_dtcs033.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_main.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_ov534_9.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_sn9c2028.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/stv06xx: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/stv06xx/gspca_stv06xx.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_spca505.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/gspca/gspca_jeilinj.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/s2255: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/s2255/s2255drv.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/zr364xx: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/zr364xx/zr364xx.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/au0828: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/au0828/au0828.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/em28xx: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/em28xx/em28xx-v4l.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/em28xx/em28xx-alsa.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/em28xx/em28xx.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/em28xx/em28xx-dvb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/stkwebcam: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/stkwebcam/stkwebcam.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/cpia2: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/cpia2/cpia2.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-anysee.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/mxl111sf-demod.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb_usb_v2.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-ec168.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-gl861.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-mxl111sf.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-af9015.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-af9035.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/mxl111sf-tuner.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-dvbsky.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-ce6230.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-az6007.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/dvb-usb-v2/dvb-usb-au6610.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/siano: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/siano/smsusb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/as102: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/as102/dvb-as102.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/pwc: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/pwc/pwc.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/b2c2: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/b2c2/b2c2-flexcop-usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/usbtv: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/media/usb/usbtv/usbtv.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/base: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/base/regmap: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/base/regmap/regmap-i2c.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/rtl8188eu: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/rtl8188eu/r8188eu.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/wlan-ng: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/wlan-ng/prism2_usb.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/rtl8723au: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/rtl8723au/r8723au.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/rtl8712: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/staging/rtl8712/r8712u.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/scsi: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/scsi/scsi_transport_iscsi.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/scsi/sd_mod.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/scsi/scsi_mod.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/mfd: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/mfd/mfd-core.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/mfd/rpisense-core.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/char: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/char/broadcom: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/char/broadcom/bcm2835-gpiomem.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/misc: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/misc/ti-st: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/misc/ti-st/st_drv.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/misc/eeprom: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/misc/eeprom/eeprom_93cx6.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/bcma: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/bcma/bcma.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/i2c: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/i2c/busses: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/i2c/busses/i2c-bcm2708.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/i2c/algos: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/i2c/algos/i2c-algo-bit.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/i2c/i2c-dev.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-rs5c348.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-max6902.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-pcf2123.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-rx4581.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-ds3232.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-rs5c372.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-ds1305.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-isl1208.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-m41t80.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-bq32k.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-isl12057.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-ds3234.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-pcf2127.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-s35390a.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-pcf8583.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-r9701.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-rx8025.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-rx8581.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-fm3130.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-ds1307.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-max6900.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-isl12022.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-x1205.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-m41t93.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-rv3029c2.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-pcf8523.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-ds1390.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-em3027.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-m41t94.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-ds1374.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-ds1672.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/rtc/rtc-pcf8563.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/class: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/class/cdc-acm.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/class/cdc-wdm.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/storage: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/storage/usb-storage.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/serial: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/serial/option.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/serial/usb_wwan.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/usb/serial/usbserial.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/spi: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/spi/spi-bcm2835.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/spi/spi-bcm2708.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid: Cannot mkdir: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-holtek-kbd.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-samsung.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-cherry.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-holtek-mouse.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-ezkey.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-monterey.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-logitech.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-microsoft.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-ortek.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-belkin.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/kernel/drivers: Cannot mkdir: No space left on device
tar: ./lib/modules/4.1.10-meye/kernel/drivers/hid/hid-holtekff.ko: Cannot open: No such file or directory
tar: ./lib/modules/4.1.10-meye/modules.symbols.bin: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.alias: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.order: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.alias.bin: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.builtin.bin: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.devname: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.dep.bin: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.builtin: Cannot write: No space left on device
tar: ./lib/modules/4.1.10-meye/modules.softdep: Cannot write: No space left on device
tar: ./lib/libpthread-2.21.so: Cannot write: No space left on device
tar: ./lib/libnss_dns-2.21.so: Cannot write: No space left on device
tar: ./lib/librt-2.21.so: Cannot write: No space left on device
tar: ./lib/ld-2.21.so: Cannot write: No space left on device
tar: ./lib/libuuid.so.1.3.0: Cannot write: No space left on device
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iptunnel: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/udevadm: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/rmmod: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iwlist: Cannot create symlink to ‘iwconfig’: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/remountrw: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/nameif: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/ifconfig: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iplink: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/start-stop-daemon: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iwgetid: Cannot create symlink to ‘iwconfig’: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/reboot: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/mount.ntfs-3g: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/udevd: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iwpriv: Cannot create symlink to ‘iwconfig’: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/slattach: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/watchdog: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iprule: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iwconfig: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/mount.lowntfs-3g: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/lsmod: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/regdbdump: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/dhclient-script: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iproute: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/plipconfig: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/dhclient: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/mii-tool: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/loadmodules: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/halt: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/syslogd: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/insmod: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/arp: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/init: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/makedevs: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/fdisk: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/crda: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/mount.cifs: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/getty: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/route: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/userinit: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/ipmaddr: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/iwspy: Cannot create symlink to ‘iwconfig’: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/fsck: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/klogd: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/poweroff: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/sysctl: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/ip: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/ipaddr: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/rarp: Cannot open: No such file or directory
tar: ./sbin: Cannot mkdir: No space left on device
tar: ./sbin/modprobe: Cannot open: No such file or directory
tar: ./root: Cannot mkdir: No space left on device
tar: ./root: Cannot mkdir: No space left on device
tar: ./root/.bash_history: Cannot open: No such file or directory
tar: ./root: Cannot mkdir: No space left on device
tar: ./root/.bash_logout: Cannot open: No such file or directory
tar: ./root: Cannot mkdir: No space left on device
tar: ./root/.bash_profile: Cannot open: No such file or directory
tar: ./proc: Cannot mkdir: No space left on device
tar: ./media: Cannot mkdir: No space left on device
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb5: Cannot mkdir: No such file or directory
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb4: Cannot mkdir: No such file or directory
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb1: Cannot mkdir: No such file or directory
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb3: Cannot mkdir: No such file or directory
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb2: Cannot mkdir: No such file or directory
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb6: Cannot mkdir: No such file or directory
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb0: Cannot mkdir: No such file or directory
tar: ./media: Cannot mkdir: No space left on device
tar: ./media/usb7: Cannot mkdir: No such file or directory
tar: ./tmp: Cannot mkdir: No space left on device
tar: ./dev: Cannot mkdir: No space left on device
tar: ./dev: Cannot mkdir: No space left on device
tar: ./dev/pts: Cannot mkdir: No such file or directory
tar: ./dev: Cannot mkdir: No space left on device
tar: ./dev/log: Cannot open: No such file or directory
tar: ./data: Cannot mkdir: No space left on device
tar: ./data: Cannot mkdir: No space left on device
tar: ./data/etc: Cannot mkdir: No such file or directory
tar: ./data: Cannot mkdir: No space left on device
tar: ./data/etc/moduli: Cannot open: No such file or directory
tar: ./data: Cannot mkdir: No space left on device
tar: ./data/etc/sshd_config: Cannot open: No such file or directory
tar: ./data: Cannot mkdir: No space left on device
tar: ./data/etc/ssh_config: Cannot open: No such file or directory
tar: ./home: Cannot mkdir: No space left on device
tar: ./home: Cannot mkdir: No space left on device
tar: ./home/ftp: Cannot mkdir: No such file or directory
tar: ./home: Cannot mkdir: No space left on device
tar: ./home/ftp/sdcard: Cannot mkdir: No such file or directory
tar: ./home: Cannot mkdir: No space left on device
tar: ./home/ftp/storage: Cannot mkdir: No such file or directory
tar: ./opt: Cannot mkdir: No space left on device
tar: ./boot: Cannot mkdir: No space left on device
tar: ./System.map: Cannot write: No space left on device
tar: ./sys: Cannot mkdir: No space left on device
tar: ./etc/ssl/certs/GlobalSign_Root_CA_-_R2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GlobalSign_Root_CA_-_R2.crt’: No space left on device
tar: ./etc/ssl/certs/TURKTRUST_Certificate_Services_Provider_Root_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TURKTRUST_Certificate_Services_Provider_Root_1.crt’: No space left on device
tar: ./etc/ssl/certs/XRamp_Global_CA_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/XRamp_Global_CA_Root.crt’: No space left on device
tar: ./etc/ssl/certs/Digital_Signature_Trust_Co._Global_CA_3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Digital_Signature_Trust_Co._Global_CA_3.crt’: No space left on device
tar: ./etc/ssl/certs/IdenTrust_Commercial_Root_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/IdenTrust_Commercial_Root_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/Visa_eCommerce_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Visa_eCommerce_Root.crt’: No space left on device
tar: ./etc/ssl/certs/TURKTRUST_Certificate_Services_Provider_Root_2007.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TURKTRUST_Certificate_Services_Provider_Root_2007.crt’: No space left on device
tar: ./etc/ssl/certs/Entrust.net_Premium_2048_Secure_Server_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Entrust.net_Premium_2048_Secure_Server_CA.crt’: No space left on device
tar: ./etc/ssl/certs/A-Trust-nQual-03.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/A-Trust-nQual-03.crt’: No space left on device
tar: ./etc/ssl/certs/EBG_Elektronik_Sertifika_Hizmet_Sağlayıcısı.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/EBG_Elektronik_Sertifika_Hizmet_Sağlayıcısı.crt’: No space left on device
tar: ./etc/ssl/certs/thawte_Primary_Root_CA_-_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/thawte_Primary_Root_CA_-_G3.crt’: No space left on device
tar: ./etc/ssl/certs/E-Tugra_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/E-Tugra_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/Deutsche_Telekom_Root_CA_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Deutsche_Telekom_Root_CA_2.crt’: No space left on device
tar: ./etc/ssl/certs/GeoTrust_Primary_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GeoTrust_Primary_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/Starfield_Root_Certificate_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Starfield_Root_Certificate_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/ComSign_Secured_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/ComSign_Secured_CA.crt’: No space left on device
tar: ./etc/ssl/certs/WellsSecure_Public_Root_Certificate_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/WellsSecure_Public_Root_Certificate_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/Certum_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Certum_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/GlobalSign_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GlobalSign_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/NetLock_Arany_=Class_Gold=_Főtanúsítvány.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/NetLock_Arany_=Class_Gold=_Főtanúsítvány.crt’: No space left on device
tar: ./etc/ssl/certs/AddTrust_Low-Value_Services_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AddTrust_Low-Value_Services_Root.crt’: No space left on device
tar: ./etc/ssl/certs/StartCom_Certification_Authority_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/StartCom_Certification_Authority_G2.crt’: No space left on device
tar: ./etc/ssl/certs/D-TRUST_Root_Class_3_CA_2_EV_2009.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/D-TRUST_Root_Class_3_CA_2_EV_2009.crt’: No space left on device
tar: ./etc/ssl/certs/ApplicationCA_-_Japanese_Government.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/ApplicationCA_-_Japanese_Government.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_Global_Root_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_Global_Root_G2.crt’: No space left on device
tar: ./etc/ssl/certs/Swisscom_Root_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Swisscom_Root_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/Go_Daddy_Class_2_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Go_Daddy_Class_2_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_2_Public_Primary_Certification_Authority_-_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_2_Public_Primary_Certification_Authority_-_G3.crt’: No space left on device
tar: ./etc/ssl/certs/TÜBİTAK_UEKAE_Kök_Sertifika_Hizmet_Sağlayıcısı_-_Sürüm_3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TÜBİTAK_UEKAE_Kök_Sertifika_Hizmet_Sağlayıcısı_-_Sürüm_3.crt’: No space left on device
tar: ./etc/ssl/certs/DST_Root_CA_X3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DST_Root_CA_X3.crt’: No space left on device
tar: ./etc/ssl/certs/Certum_Trusted_Network_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Certum_Trusted_Network_CA.crt’: No space left on device
tar: ./etc/ssl/certs/QuoVadis_Root_CA_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/QuoVadis_Root_CA_2.crt’: No space left on device
tar: ./etc/ssl/certs/NetLock_Express_=Class_C=_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/NetLock_Express_=Class_C=_Root.crt’: No space left on device
tar: ./etc/ssl/certs/Network_Solutions_Certificate_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Network_Solutions_Certificate_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/AffirmTrust_Networking.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AffirmTrust_Networking.crt’: No space left on device
tar: ./etc/ssl/certs/Security_Communication_EV_RootCA1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Security_Communication_EV_RootCA1.crt’: No space left on device
tar: ./etc/ssl/certs/Swisscom_Root_CA_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Swisscom_Root_CA_2.crt’: No space left on device
tar: ./etc/ssl/certs/UTN_USERFirst_Email_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/UTN_USERFirst_Email_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/QuoVadis_Root_CA_1_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/QuoVadis_Root_CA_1_G3.crt’: No space left on device
tar: ./etc/ssl/certs/COMODO_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/COMODO_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/TC_TrustCenter_Universal_CA_I.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TC_TrustCenter_Universal_CA_I.crt’: No space left on device
tar: ./etc/ssl/certs/Sonera_Class_2_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Sonera_Class_2_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Go_Daddy_Root_Certificate_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Go_Daddy_Root_Certificate_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/Secure_Global_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Secure_Global_CA.crt’: No space left on device
tar: ./etc/ssl/certs/AffirmTrust_Premium.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AffirmTrust_Premium.crt’: No space left on device
tar: ./etc/ssl/certs/Comodo_AAA_Services_root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Comodo_AAA_Services_root.crt’: No space left on device
tar: ./etc/ssl/certs/SG_TRUST_SERVICES_RACINE.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/SG_TRUST_SERVICES_RACINE.crt’: No space left on device
tar: ./etc/ssl/certs/Equifax_Secure_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Equifax_Secure_CA.crt’: No space left on device
tar: ./etc/ssl/certs/thawte_Primary_Root_CA_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/thawte_Primary_Root_CA_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/USERTrust_ECC_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/USERTrust_ECC_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_1_Public_Primary_Certification_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_1_Public_Primary_Certification_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/Atos_TrustedRoot_2011.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Atos_TrustedRoot_2011.crt’: No space left on device
tar: ./etc/ssl/certs/Swisscom_Root_EV_CA_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Swisscom_Root_EV_CA_2.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_Assured_ID_Root_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_Assured_ID_Root_G2.crt’: No space left on device
tar: ./etc/ssl/certs/T-TeleSec_GlobalRoot_Class_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/T-TeleSec_GlobalRoot_Class_2.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_1_Public_Primary_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_1_Public_Primary_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/ACEDICOM_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/ACEDICOM_Root.crt’: No space left on device
tar: ./etc/ssl/certs/StartCom_Certification_Authority_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/StartCom_Certification_Authority_2.crt’: No space left on device
tar: ./etc/ssl/certs/Microsec_e-Szigno_Root_CA_2009.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Microsec_e-Szigno_Root_CA_2009.crt’: No space left on device
tar: ./etc/ssl/certs/T-TeleSec_GlobalRoot_Class_3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/T-TeleSec_GlobalRoot_Class_3.crt’: No space left on device
tar: ./etc/ssl/certs/Buypass_Class_3_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Buypass_Class_3_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/TWCA_Root_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TWCA_Root_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/AffirmTrust_Commercial.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AffirmTrust_Commercial.crt’: No space left on device
tar: ./etc/ssl/certs/Camerfirma_Global_Chambersign_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Camerfirma_Global_Chambersign_Root.crt’: No space left on device
tar: ./etc/ssl/certs/NetLock_Notary_=Class_A=_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/NetLock_Notary_=Class_A=_Root.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_4_Public_Primary_Certification_Authority_-_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_4_Public_Primary_Certification_Authority_-_G3.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_3_Public_Primary_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_3_Public_Primary_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/QuoVadis_Root_CA_3_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/QuoVadis_Root_CA_3_G3.crt’: No space left on device
tar: ./etc/ssl/certs/Baltimore_CyberTrust_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Baltimore_CyberTrust_Root.crt’: No space left on device
tar: ./etc/ssl/certs/Comodo_Trusted_Services_root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Comodo_Trusted_Services_root.crt’: No space left on device
tar: ./etc/ssl/certs/Starfield_Class_2_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Starfield_Class_2_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Digital_Signature_Trust_Co._Global_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Digital_Signature_Trust_Co._Global_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_3_Public_Primary_Certification_Authority_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_3_Public_Primary_Certification_Authority_2.crt’: No space left on device
tar: ./etc/ssl/certs/QuoVadis_Root_CA_2_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/QuoVadis_Root_CA_2_G3.crt’: No space left on device
tar: ./etc/ssl/certs/TC_TrustCenter_Class_3_CA_II.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TC_TrustCenter_Class_3_CA_II.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_3_Public_Primary_Certification_Authority_-_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_3_Public_Primary_Certification_Authority_-_G3.crt’: No space left on device
tar: ./etc/ssl/certs/Root_CA_Generalitat_Valenciana.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Root_CA_Generalitat_Valenciana.crt’: No space left on device
tar: ./etc/ssl/certs/Equifax_Secure_eBusiness_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Equifax_Secure_eBusiness_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_2_Public_Primary_Certification_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_2_Public_Primary_Certification_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/SwissSign_Platinum_CA_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/SwissSign_Platinum_CA_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/Buypass_Class_2_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Buypass_Class_2_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/Staat_der_Nederlanden_EV_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Staat_der_Nederlanden_EV_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/S-TRUST_Authentication_and_Encryption_Root_CA_2005_PN.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/S-TRUST_Authentication_and_Encryption_Root_CA_2005_PN.crt’: No space left on device
tar: ./etc/ssl/certs/TURKTRUST_Certificate_Services_Provider_Root_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TURKTRUST_Certificate_Services_Provider_Root_2.crt’: No space left on device
tar: ./etc/ssl/certs/AddTrust_Qualified_Certificates_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AddTrust_Qualified_Certificates_Root.crt’: No space left on device
tar: ./etc/ssl/certs/AC_Raíz_Certicámara_S.A..pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AC_Raíz_Certicámara_S.A..crt’: No space left on device
tar: ./etc/ssl/certs/TeliaSonera_Root_CA_v1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TeliaSonera_Root_CA_v1.crt’: No space left on device
tar: ./etc/ssl/certs/Staat_der_Nederlanden_Root_CA_-_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Staat_der_Nederlanden_Root_CA_-_G3.crt’: No space left on device
tar: ./etc/ssl/certs/StartCom_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/StartCom_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/EE_Certification_Centre_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/EE_Certification_Centre_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Comodo_Secure_Services_root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Comodo_Secure_Services_root.crt’: No space left on device
tar: ./etc/ssl/certs/certSIGN_ROOT_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/certSIGN_ROOT_CA.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_Trusted_Root_G4.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_Trusted_Root_G4.crt’: No space left on device
tar: ./etc/ssl/certs/VeriSign_Universal_Root_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/VeriSign_Universal_Root_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/D-TRUST_Root_Class_3_CA_2_2009.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/D-TRUST_Root_Class_3_CA_2_2009.crt’: No space left on device
tar: ./etc/ssl/certs/GeoTrust_Primary_Certification_Authority_-_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GeoTrust_Primary_Certification_Authority_-_G3.crt’: No space left on device
tar: ./etc/ssl/certs/Autoridad_de_Certificacion_Firmaprofesional_CIF_A62634068.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Autoridad_de_Certificacion_Firmaprofesional_CIF_A62634068.crt’: No space left on device
tar: ./etc/ssl/certs/Starfield_Services_Root_Certificate_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Starfield_Services_Root_Certificate_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/AddTrust_External_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AddTrust_External_Root.crt’: No space left on device
tar: ./etc/ssl/certs/OISTE_WISeKey_Global_Root_GA_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/OISTE_WISeKey_Global_Root_GA_CA.crt’: No space left on device
tar: ./etc/ssl/certs/GeoTrust_Primary_Certification_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GeoTrust_Primary_Certification_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/Entrust_Root_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Entrust_Root_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/GlobalSign_ECC_Root_CA_-_R5.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GlobalSign_ECC_Root_CA_-_R5.crt’: No space left on device
tar: ./etc/ssl/certs/GlobalSign_ECC_Root_CA_-_R4.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GlobalSign_ECC_Root_CA_-_R4.crt’: No space left on device
tar: ./etc/ssl/certs/Entrust_Root_Certification_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Entrust_Root_Certification_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/TWCA_Global_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TWCA_Global_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Microsec_e-Szigno_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Microsec_e-Szigno_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/thawte_Primary_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/thawte_Primary_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/COMODO_ECC_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/COMODO_ECC_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/RSA_Security_2048_v3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/RSA_Security_2048_v3.crt’: No space left on device
tar: ./etc/ssl/certs/VeriSign_Class_3_Public_Primary_Certification_Authority_-_G5.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/VeriSign_Class_3_Public_Primary_Certification_Authority_-_G5.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_1_Public_Primary_Certification_Authority_-_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_1_Public_Primary_Certification_Authority_-_G3.crt’: No space left on device
tar: ./etc/ssl/certs/China_Internet_Network_Information_Center_EV_Certificates_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/China_Internet_Network_Information_Center_EV_Certificates_Root.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_Assured_ID_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_Assured_ID_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/UTN_USERFirst_Hardware_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/UTN_USERFirst_Hardware_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/S-TRUST_Universal_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/S-TRUST_Universal_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Security_Communication_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Security_Communication_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/COMODO_RSA_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/COMODO_RSA_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/NetLock_Qualified_=Class_QA=_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/NetLock_Qualified_=Class_QA=_Root.crt’: No space left on device
tar: ./etc/ssl/certs/CA_Disig_Root_R1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/CA_Disig_Root_R1.crt’: No space left on device
tar: ./etc/ssl/certs/Staat_der_Nederlanden_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Staat_der_Nederlanden_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/ePKI_Root_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/ePKI_Root_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/Trustis_FPS_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Trustis_FPS_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Global_Chambersign_Root_-_2008.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Global_Chambersign_Root_-_2008.crt’: No space left on device
tar: ./etc/ssl/certs/SwissSign_Silver_CA_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/SwissSign_Silver_CA_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/SecureSign_RootCA11.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/SecureSign_RootCA11.crt’: No space left on device
tar: ./etc/ssl/certs/Hongkong_Post_Root_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Hongkong_Post_Root_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/spi-cacert-2008.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/spi-inc.org/spi-cacert-2008.crt’: No space left on device
tar: ./etc/ssl/certs/VeriSign_Class_3_Public_Primary_Certification_Authority_-_G4.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/VeriSign_Class_3_Public_Primary_Certification_Authority_-_G4.crt’: No space left on device
tar: ./etc/ssl/certs/Certplus_Class_2_Primary_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Certplus_Class_2_Primary_CA.crt’: No space left on device
tar: ./etc/ssl/certs/UTN_DATACorp_SGC_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/UTN_DATACorp_SGC_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_Assured_ID_Root_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_Assured_ID_Root_G3.crt’: No space left on device
tar: ./etc/ssl/certs/TC_TrustCenter_Class_2_CA_II.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/TC_TrustCenter_Class_2_CA_II.crt’: No space left on device
tar: ./etc/ssl/certs/Cybertrust_Global_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Cybertrust_Global_Root.crt’: No space left on device
tar: ./etc/ssl/certs/Chambers_of_Commerce_Root_-_2008.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Chambers_of_Commerce_Root_-_2008.crt’: No space left on device
tar: ./etc/ssl/certs/Certinomis_-_Autorité_Racine.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Certinomis_-_Autorité_Racine.crt’: No space left on device
tar: ./etc/ssl/certs/QuoVadis_Root_CA_3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/QuoVadis_Root_CA_3.crt’: No space left on device
tar: ./etc/ssl/certs/Entrust_Root_Certification_Authority_-_EC1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Entrust_Root_Certification_Authority_-_EC1.crt’: No space left on device
tar: ./etc/ssl/certs/SecureTrust_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/SecureTrust_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Buypass_Class_3_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Buypass_Class_3_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/DST_ACES_CA_X6.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DST_ACES_CA_X6.crt’: No space left on device
tar: ./etc/ssl/certs/AddTrust_Public_Services_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AddTrust_Public_Services_Root.crt’: No space left on device
tar: ./etc/ssl/certs/GeoTrust_Universal_CA_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GeoTrust_Universal_CA_2.crt’: No space left on device
tar: ./etc/ssl/certs/Hellenic_Academic_and_Research_Institutions_RootCA_2011.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Hellenic_Academic_and_Research_Institutions_RootCA_2011.crt’: No space left on device
tar: ./etc/ssl/certs/Sonera_Class_1_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Sonera_Class_1_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_High_Assurance_EV_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_High_Assurance_EV_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/AffirmTrust_Premium_ECC.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/AffirmTrust_Premium_ECC.crt’: No space left on device
tar: ./etc/ssl/certs/USERTrust_RSA_Certification_Authority.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/USERTrust_RSA_Certification_Authority.crt’: No space left on device
tar: ./etc/ssl/certs/Verisign_Class_3_Public_Primary_Certification_Authority_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Verisign_Class_3_Public_Primary_Certification_Authority_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/GeoTrust_Universal_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GeoTrust_Universal_CA.crt’: No space left on device
tar: ./etc/ssl/certs/QuoVadis_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/QuoVadis_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Staat_der_Nederlanden_Root_CA_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Staat_der_Nederlanden_Root_CA_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_Global_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_Global_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/IdenTrust_Public_Sector_Root_CA_1.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/IdenTrust_Public_Sector_Root_CA_1.crt’: No space left on device
tar: ./etc/ssl/certs/DigiCert_Global_Root_G3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/DigiCert_Global_Root_G3.crt’: No space left on device
tar: ./etc/ssl/certs/Buypass_Class_2_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Buypass_Class_2_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Equifax_Secure_Global_eBusiness_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Equifax_Secure_Global_eBusiness_CA.crt’: No space left on device
tar: ./etc/ssl/certs/Actalis_Authentication_Root_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Actalis_Authentication_Root_CA.crt’: No space left on device
tar: ./etc/ssl/certs/CA_Disig_Root_R2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/CA_Disig_Root_R2.crt’: No space left on device
tar: ./etc/ssl/certs/SwissSign_Gold_CA_-_G2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/SwissSign_Gold_CA_-_G2.crt’: No space left on device
tar: ./etc/ssl/certs/GlobalSign_Root_CA_-_R3.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GlobalSign_Root_CA_-_R3.crt’: No space left on device
tar: ./etc/ssl/certs/GeoTrust_Global_CA.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GeoTrust_Global_CA.crt’: No space left on device
tar: ./etc/ssl/certs/GeoTrust_Global_CA_2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/GeoTrust_Global_CA_2.crt’: No space left on device
tar: ./etc/ssl/certs/NetLock_Business_=Class_B=_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/NetLock_Business_=Class_B=_Root.crt’: No space left on device
tar: ./etc/ssl/certs/Camerfirma_Chambers_of_Commerce_Root.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Camerfirma_Chambers_of_Commerce_Root.crt’: No space left on device
tar: ./etc/ssl/certs/Security_Communication_RootCA2.pem: Cannot create symlink to ‘../../../usr/share/ca-certificates/mozilla/Security_Communication_RootCA2.crt’: No space left on device
tar: Exiting with failure status due to previous errors

Multi Email addresses

Hi

It would be nice to have the ability to add more than one email for the alert to go to.

Regards

Damian

stat Command

Hi, I notice in the source that you use coreutils 8.24. This webpage says taht the command 'stat' is included? http://www.linuxfromscratch.org/clfs/view/clfs-2.0/arm/final-system/coreutils.html When I try to use it it complains about '-sh: stat: command not found'. If it is not in the build can you please tell me how to get it in. The reason is I want to use this page to get Dropbox running. http://raspi.tv/2013/how-to-use-dropbox-with-raspberry-pi

Thank you for all your hard work.

Extra Motion Options incorrect after reboot

Hi,

first off all thank you for the great support.
Unfortunately after every reboot the values in the Extra Motion Options changes from "on" to "true" or "off" to "false".

For example "output_secondary_pictures on" changes after reboot to "output_secondary_pictures true".
So motion doesn't understand the option and uses the default.

Solid white speckle

Now when the snowy season has started, false triggers is becoming a hassle.

Snow, rain and bugs that come too close to the sensor, are all white. People, cars and other things that are far away, are never all white.

So, is there a way to "cancel out" solid white speckle" that triggers the motion detection?

Offline mode

Will it be possible to have an offline mode in order to detect motion even in place without internet access ? I would like to get that in order to install it on construction site.

thanks in advance for your help

Anyone have a solution to sync with DropBox

I saw the google Drive one, is there a similiar method?

Motionpie v.s. MotionEyeOS

Hello,

First of all thanks for this nice update, but after updateing 1 Rasbp2 (i have 5 ) i find the following :

Please note that the setup + hardware are 100% same and i have both configured the overclocking to medium (950/250/450/0) they are both on 100Mbit /Full wired
I don't use recording through the motionPie /motionEyeOs, only got Streaming enabled so my QNAP can record this.

Rasp 2 with MotionPie :

Camera : usb-Microsoft_Microsoft®_LifeCam_HD-3000-video-index0
Resolution: 800x448
Frame Rate: -- / 18
Bit Rate: 6.3 Mbps
Quality: --
Recording Status: Recording

MotionEyeOS :

Camera : usb-Microsoft_Microsoft®_LifeCam_HD-3000-video-index0
Resolution: 800x448
Frame Rate: -- / 10
Bit Rate: 7.2 Mbps
Quality: --
Recording Status: Recording

If i change back the OS to MotionPie i get the right framerate again !
What is it i am doing wrong ???

Email notification problem

Hello,
I am behind a router, so the raspberry pi B has access to internet.
Please advise
I've been trying with gmail account:
2015-10-13 20:49:17: [sendmail] ERROR: failed to send mail: (534, '5.7.14 <https://accounts.google.com/ContinueSignIn?sarp=1&scc=1&plt=AKgnsbsfE\n5.7.14 dovOr0AipLQF0Pp9SxNPSxSnf3QRcCAIozB--blrclJaBDd50LWA-gBl4ALCJHj4T8i35O\n5.7.14 I-Xa7llM3OhcYelEQCZYSJAKHDlQ5bIxDlOq5EflSY6EM1LcSO8iiuiIPveZWeOIyv28mf\n5.7.14 VPEvAXdLC6oRtzybdyzjdeSsy8bGQnJ45SsKYgR1N9sKcMX3_YPhHAuZBXELPY6xwbmX6i\n5.7.14 5ypMmdBHrV0jlq_eQtsobBtzeEjY> Please log in via your web browser and\n5.7.14 then try again.\n5.7.14 Learn more at\n5.7.14 https://support.google.com/mail/answer/78754 gt4sm16082779wib.21 - gsmtp')
Traceback (most recent call last):
File "/home/ccrisan/motioneyeos/output/raspberrypi/target/usr/lib/python2.7/site-packages/motioneye/sendmail.py", line 178, in on_message
File "/home/ccrisan/motioneyeos/output/raspberrypi/target/usr/lib/python2.7/site-packages/motioneye/sendmail.py", line 54, in send_mail
File "/usr/lib/python2.7/smtplib.py", line 622, in login
SMTPAuthenticationError: (534, '5.7.14 <https://accounts.google.com/ContinueSignIn?sarp=1&scc=1&plt=AKgnsbsfE\n5.7.14 dovOr0AipLQF0Pp9SxNPSxSnf3QRcCAIozB--blrclJaBDd50LWA-gBl4ALCJHj4T8i35O\n5.7.14 I-Xa7llM3OhcYelEQCZYSJAKHDlQ5bIxDlOq5EflSY6EM1LcSO8iiuiIPveZWeOIyv28mf\n5.7.14 VPEvAXdLC6oRtzybdyzjdeSsy8bGQnJ45SsKYgR1N9sKcMX3_YPhHAuZBXELPY6xwbmX6i\n5.7.14 5ypMmdBHrV0jlq_eQtsobBtzeEjY> Please log in via your web browser and\n5.7.14 then try again.\n5.7.14 Learn more at\n5.7.14 https://support.google.com/mail/answer/78754 gt4sm16082779wib.21 - gsmtp')
2015-10-13 20:50:06: [sendmail] ERROR: failed to send mail: (534, '5.7.14 <https://accounts.google.com/ContinueSignIn?sarp=1&scc=1&plt=AKgnsbv-0\n5.7.14 VUSJavXzBie_XgnuiogePombkrUWjLQ-dDhfhbiSCaPbFFESUkAXdNo0EwigP84wlWwdDx\n5.7.14 NStXJViC_qHv_XL3zLU-uvVsXIrfpstVbs0pv9nUGwYEbgZoqSzqSUv9_n7Jk41R5GCPwo\n5.7.14 s1KWbHIOswJAaZQO9G1kQ7ez_E1h9LIeSzUtjZ6YqWONt7eaLNPPdG4x4XDnyBDPwyEiiy\n5.7.14 svNKCff8fm35Gfr5_q8_QLcULTtg> Please log in via your web browser and\n5.7.14 then try again.\n5.7.14 Learn more at\n5.7.14 https://support.google.com/mail/answer/78754 ub7sm3945435wib.17 - gsmtp')
Traceback (most recent call last):
File "/home/ccrisan/motioneyeos/output/raspberrypi/target/usr/lib/python2.7/site-packages/motioneye/sendmail.py", line 178, in on_message
File "/home/ccrisan/motioneyeos/output/raspberrypi/target/usr/lib/python2.7/site-packages/motioneye/sendmail.py", line 54, in send_mail
File "/usr/lib/python2.7/smtplib.py", line 622, in login
SMTPAuthenticationError: (534, '5.7.14 <https://accounts.google.com/ContinueSignIn?sarp=1&scc=1&plt=AKgnsbv-0\n5.7.14 VUSJavXzBie_XgnuiogePombkrUWjLQ-dDhfhbiSCaPbFFESUkAXdNo0EwigP84wlWwdDx\n5.7.14 NStXJViC_qHv_XL3zLU-uvVsXIrfpstVbs0pv9nUGwYEbgZoqSzqSUv9_n7Jk41R5GCPwo\n5.7.14 s1KWbHIOswJAaZQO9G1kQ7ez_E1h9LIeSzUtjZ6YqWONt7eaLNPPdG4x4XDnyBDPwyEiiy\n5.7.14 svNKCff8fm35Gfr5_q8_QLcULTtg> Please log in via your web browser and\n5.7.14 then try again.\n5.7.14 Learn more at\n5.7.14 https://support.google.com/mail/answer/78754 ub7sm3945435wib.17 - gsmtp')
2015-10-13 20:51:43: [sendmail] ERROR: failed to send mail: [Errno 97] Address family not supported by protocol

And Yahoo Account:
2015-10-14 07:10:45: [sendmail] ERROR: failed to send mail: Connection unexpectedly closed: timed out
Traceback (most recent call last):
File "/home/ccrisan/motioneyeos/output/raspberrypi/target/usr/lib/python2.7/site-packages/motioneye/sendmail.py", line 178, in on_message
File "/home/ccrisan/motioneyeos/output/raspberrypi/target/usr/lib/python2.7/site-packages/motioneye/sendmail.py", line 49, in send_mail
File "/usr/lib/python2.7/smtplib.py", line 256, in init
File "/usr/lib/python2.7/smtplib.py", line 317, in connect
File "/usr/lib/python2.7/smtplib.py", line 365, in getreply
SMTPServerDisconnected: Connection unexpectedly closed: timed out

Also with my ISP account, all with or without TLS, tried ports 25, 465 and 587.

Snapshot doesn't work after about 15 seconds

Raspberry Pi2 running the latest release: 20151103

If I get a snapshot from http://m200pi/picture/1/current/ every 10 seconds it works fine, but if I wait 15 seconds, I get a zero size file returned.

Does the same thing in my Perl code and Safari browser.

Move /data to USB

How would I go about moving /data to a USB-stick?

I tried the regular route by changing /etc/fstab's /data to /dev/sda1, but that didn't work.

How to synchronize with Google Drive

motionEyeOS is great, but having seen a number of requests for Google Drive functionality, I thought I should share how I got it working.

Here are step-by-step instructions which also work with motionPie:

• Ensure that you have set a motionEyeOS admin password through the web interface and have rebooted
• Using SSH, login as root with your admin password from a Mac, Linux or Windows PC
• Enter and execute the following commands. You can do so one line at a time or just copy and paste
  the whole block into your SSH session:

# mount the root volume as read/write
mount -o remount,rw /
# change to the /usr/bin directory where we will keep the gdrive executable
cd /usr/bin
# download a pre-built gdrive binary file
wget https://github.com/odeke-em/drive/releases/download/v0.2.2-arm-binary/drive-arm-binary
# make it executable
chmod +x drive-arm-binary
# rename it to gdrive
mv drive-arm-binary gdrive
# change the root volume back to read-only
mount -o remount,ro /
# create a gdrive directory on the data volume
mkdir /data/gdrive
# change to that directory
cd /data/gdrive
# download Emil Janesten's greatly improved version of Claude Pageau's sync.sh script 
wget https://gist.githubusercontent.com/Limeliz/4389cc40744331736c59/raw/bee4809bcf3a8eef01a9d8394d996eaf4d8ae1ec/sync.sh
# make the script executable
chmod +x sync.sh
# create a symbolic link to the motion output folder
ln -s /data/output output

• Now you'll want to link gdrive to your Google account. Open a browser on your PC and ensure
  that you are logged into Google (for example, you could open Gmail).

Back in your SSH session, enter and execute:

gdrive init

This will produce a long, complex URL which you should copy and paste into your PC browser's
address line, then press Enter.

You'll need to give permission to manage files in your Google Drive and will then be returned a
code to copy back into your SSH session where gdrive is waiting.

A success will return nothing.

• Finally, you should add a cron entry to copy over files from the motion output folder to Google
  Drive on a regular schedule.

    # set the crontab editor to be nano (I'm much more comfortable with nano than vi)
      export EDITOR=nano
    # enter crontab editor
      crontab -e

• Now set the task to run every five minutes by pasting in:

*/5 * * * * /data/gdrive/sync.sh >> /data/log/gdrive_output.log 2>&1

Then quit nano with control-x and save the crontab entry.

That's it. You can have it up and running in about five minutes and it seems to work without any
unforeseen problems.

***Modified on 11-20-2015 to incorporate changes suggested by Limeliz

video encoding in hardware

Hi,
Would motioneyeos be able to take advantage of enabling mpeg-2 hardware encoding as per http://swag.raspberrypi.org/collections/software/products/mpeg-2-license-key?

many thanks,

No video on multi cams with higher resolution.

Been running MotionEyeOS with a single 720p cam on a Pi2 for some time, and lovin' it ;)

Now added a second 720p webcam, but video simply stops (no cam icon) as soon as resolution reaches 640x480 (and upwards) even with lowest framerate setting on both cams... though 1280x720 on 1st, and 320x240 on 2nd cam (or vice versa) works fine with high framerate.

Playing with settings (text/streaming/stills/movies/motion disabled) doesn't seem to help.
When video stops, Motioneye.log contains lots of following warnings (x being a number);
"[motioneye] WARNING: Connect error on fd x: ECONNREFUSED"

Any suggestions in troubleshooting ?
What are the known limitations (terms of number of cams, resolution, framerate) running a Pi2 ?

Thanks for any help!
Woale