omegaphi115/draconic-evolution-reactor-controller

Draconic Evolution Reactor Controller

• Monitor and failsafe automation for your draconic evolution reactor
• This program is based of acidjazz's code. Link to the original: https://github.com/acidjazz/drmon

What is this ?

This is a computercraft (opencomputers might work but they are not tested) LUA script that monitors everything about a draconic reactor, with a couple features to help keep it from exploding

Tutorial:

Not done yet

Features:

• Uses a 3x3 advanced computer touchscreen monitor to interact with your reactor
• Automated regulation of the input gate for the targeted field strength of 50%
  • adjustable
• Immediate shutdown and charge upon your field strength going below 20%
  • adjustable
• Immediate shutdown when your temperature goes above 8000C°
  • adjustable
• Safe cooling down system
• Easily tweak your output flux gate via touchscreen buttons
  • +/-100k, 10k, and 1k increments

Requirements:

• one fully setup draconic reactor (and fuel, obviously)
• 1 advanced computer
• 9 advanced monitors
• 3 wired modems, wireless will not work
• a bunch of network cables

Installation:

• Your reactor output flux gate must be setup so that one side of it and one of your stabilizers touches a side of the advanced computer
• By default, flux gate should touch the top side, stabilizer on the left of the computer
  • If you want to use different sides you need to modify startup after you have installed this and specify the sides
• Connect a modem to your input flux gate (the one connected to your reactor energy injector)
• Connect a modem to your advanced computer (at the botom side)
• Setup your monitors to be a 3x3 and connect a modem to anywhere but the front
• Run network cable to all 3 modems
• Install this code via running the install script using these commands :

> pastebin get rhNbNbFE install
> install

• Modify startup if you wish to configure/alter any variables mentioned in the feature list, you'll find them at the top of the file
• You should see stats in your terminal, and on your monitor

Upgrading to the latest version

• Hold ctrl+t until you get a >

> install

Warnings

• There can have bugs so please report them in the issue tab above
• Also try to put your reactor in a RF Tools dimension or realy far away and make backups with mods like aroma backups to prevent damage in case of an explosion

draconic-evolution-reactor-controller's Issues

Reactor Controls

I see that there is a tab that says reactor control...how do i access them? do i have to just use the reactor stabilizer to turn it on/off? or is there a way to do that from the screen? thanks

Call me a noob, but how do I install the program? (1.12.2)

Like, is there a base mod I need? If so, how do I integrate this with said base mod?

Script not working

Startup error/program turns off when reactor is activated

.temp:280: attempt to perform arithmetic __mul on nil and number

can there be a tutorial on how to set this up?

title ^

How to set up?

(This isnt really an issue its more of me needing help with setting up the program)

I think ive got it set up but when it runs it gives me a error saying "No valid fluxgate was found" even if the fluxgate is to the right of the computer

does anyone know how to set this up?

Error on start up

acidjazz/drmon#15

This one doesn't work at all

The input gate gets locked at 100,000,000 RF/tick.
The temp gets locked at 2000C.
The reactor shuts down a few minutes after starting up.

Is this still being worked on?

I was wondering if this is still being worked on since the last update was 3 years ago.

Automatic Shield Stabilization Not Working

acidjazz/drmon#16

The program crashes when the reactor is activated.

startup:280: attempt to preform arithmetic __mul on nil and number

Screen filckering

Solution:
get setings
clean screen
write

Tutorial Please

My Reactor keep exploding after a while running the program and i dont know why.... this is so frustrating. Please make a Video how to setup the reactor for 1.12.2

Install don't update

Program Crashing when Changing To Automatic Input

When i try to Change the input to Automatic the Program Crashes and the Reactor explodes after a while.

Edit: When you turn Fail save on it works

Edit 2: I just tought it was fixed but i didnt turn the reactor on so the Problem is as described