ralfano/gettingandcleaningdatacourseproject

Content

• Introduction
• Code Book
• Instruction list

Introduction

Alfano's "Getting and Cleaning Data" project submission

Code Book

Variables in the data set not contained in the tidy data

For each record it is provided:

• Triaxial acceleration from the accelerometer (total acceleration) and the estimated body acceleration.
• Triaxial Angular velocity from the gyroscope.
• A 561-feature vector with time and frequency domain variables.

The features selected for this database come from the accelerometer and gyroscope 3-axial raw signals tAcc-XYZ and tGyro-XYZ. These time domain signals (prefix 't' to denote time) were captured at a constant rate of 50 Hz. Then they were filtered using a median filter and a 3rd order low pass Butterworth filter with a corner frequency of 20 Hz to remove noise. Similarly, the acceleration signal was then separated into body and gravity acceleration signals (tBodyAcc-XYZ and tGravityAcc-XYZ) using another low pass Butterworth filter with a corner frequency of 0.3 Hz.

Subsequently, the body linear acceleration and angular velocity were derived in time to obtain Jerk signals (tBodyAccJerk-XYZ and tBodyGyroJerk-XYZ). Also the magnitude of these three-dimensional signals were calculated using the Euclidean norm (tBodyAccMag, tGravityAccMag, tBodyAccJerkMag, tBodyGyroMag, tBodyGyroJerkMag).

Finally a Fast Fourier Transform (FFT) was applied to some of these signals producing fBodyAcc-XYZ, fBodyAccJerk-XYZ, fBodyGyro-XYZ, fBodyAccJerkMag, fBodyGyroMag, fBodyGyroJerkMag. (Note the 'f' to indicate frequency domain signals).

These signals were used to estimate variables of the feature vector for each pattern:
'-XYZ' is used to denote 3-axial signals in the X, Y and Z directions.

tBodyAcc-XYZ tGravityAcc-XYZ tBodyAccJerk-XYZ tBodyGyro-XYZ tBodyGyroJerk-XYZ tBodyAccMag tGravityAccMag tBodyAccJerkMag tBodyGyroMag tBodyGyroJerkMag fBodyAcc-XYZ fBodyAccJerk-XYZ fBodyGyro-XYZ fBodyAccMag fBodyAccJerkMag fBodyGyroMag fBodyGyroJerkMag

The set of variables that were estimated from these signals are:

mean(): Mean value std(): Standard deviation mad(): Median absolute deviation max(): Largest value in array min(): Smallest value in array sma(): Signal magnitude area energy(): Energy measure. Sum of the squares divided by the number of values. iqr(): Interquartile range entropy(): Signal entropy arCoeff(): Autorregresion coefficients with Burg order equal to 4 correlation(): correlation coefficient between two signals maxInds(): index of the frequency component with largest magnitude meanFreq(): Weighted average of the frequency components to obtain a mean frequency skewness(): skewness of the frequency domain signal kurtosis(): kurtosis of the frequency domain signal bandsEnergy(): Energy of a frequency interval within the 64 bins of the FFT of each window. angle(): Angle between to vectors.

Additional vectors obtained by averaging the signals in a signal window sample. These are used on the angle() variable:

gravityMean tBodyAccMean tBodyAccJerkMean tBodyGyroMean tBodyGyroJerkMean

Summary Choices

The following steps have been followed in order to summary the data:

• We have created a merge of the training and the test sets to create one data set.
• We have extracted only the measurements on the mean and standard deviation for each measurement.
• We have joined the descriptive activity names to name the activities in the data set
• We have labeled the data set with descriptive variable names.
• From the data set in step 4, we have created a second, independent tidy data set with the average of each variable for each activity and each subject.

Instruction list

• Open a command line prompt

• Goto a preferred working directory

• Clone the repository with the following command:

git clone https://github.com/ralfano/GettingandCleaningDataCourseProject.git

• Change your working directory to .\GettingandCleaningDataCourseProject

• Run the run_analysis.R script with the following command:

Rscript run_analysis.R

• When the script terminates a file named "tidydataset.txt" with the final result must appear in the current working directory