sharandac/vindriktning

Let's make the Ikea Vindriktning air quality sensor a little smarter. Here is the matching completely over-engineered firmware.

   

---

Vindriktning

Let's make the Ikea Vindriktning air quality sensor a little smarter. Here is the matching completely over-engineered firmware.

prerequisite

ESP32 - Mini D1
Ikea Vindriktning

Install

Clone this repository and open it with platformIO. Remember, the SPIFF must also be flashed. On a terminal in vscode you can do it with

pio run -t uploadfs
pio run -t upload

After that, take a look at your monitorport ...

[I][vindriktning.cpp:65] vindriktning_Task(): Start Vindriktning Task on Core: 1
[I][wificlient.cpp:91] wificlient_Task(): Start Wifi-Client on Core: 1
[I][wificlient.cpp:108] wificlient_Task(): WiFi connection lost, restart ... 
[I][wificlient.cpp:398] wificlient_start_softAP(): starting Wifi-AP with SSID "vindriktning_d1fd28" / "vindriktning"
[I][wificlient.cpp:399] wificlient_start_softAP(): AP IP address: 192.168.4.1
[I][webserver.cpp:56] asyncwebserver_Task(): Start Webserver on Core: 1
[I][ntp.cpp:65] ntp_Task(): Start NTP Task on Core: 1
[I][mqttclient.cpp:320] mqtt_client_Task(): Start MQTT-Client on Core: 1
[I][callback.cpp:31] callback_print():  |
[I][callback.cpp:32] callback_print():  +--'mqtt client' ( 0x3ffb97a8 / 1 )
[I][callback.cpp:34] callback_print():  |  +--id:'vindriktning', event mask:0001, prio: 2, active: true
[I][callback.cpp:31] callback_print():  |
[I][callback.cpp:32] callback_print():  +--'webserver' ( 0x3ffb97fc / 7 )
[I][callback.cpp:34] callback_print():  |  +--id:'/vindriktning.htm', event mask:001f, prio: 2, active: true
[I][callback.cpp:34] callback_print():  |  +--id:'/index.htm', event mask:0007, prio: 1, active: true
[I][callback.cpp:34] callback_print():  |  +--id:'/wlan.htm', event mask:001f, prio: 3, active: true
[I][callback.cpp:34] callback_print():  |  +--id:'/update.htm', event mask:0007, prio: 3, active: true
[I][callback.cpp:34] callback_print():  |  +--id:'/info.htm', event mask:0007, prio: 3, active: true
[I][callback.cpp:34] callback_print():  |  +--id:'/mqttclient.htm', event mask:001f, prio: 2, active: true
[I][callback.cpp:34] callback_print():  |  +--id:'/ntp.htm', event mask:001f, prio: 2, active: true

When the output look like this, congratulation!

After the first start an access point will be opened with an unique name like

vindriktning_XXXXX

and an not so unique password

vindriktning

After that you can configure the vindriktning under the following IP-address with your favorite webbrowser

http://192.168.4.1

hardware modification in 4 steps

esp32 -> Vindriktning:

VCC -> +5V
GND -> GND
GPIO16 -> reset

Contributors

Every Contribution to this repository is highly welcome! Don't fear to create pull requests which enhance or fix the project, you are going to help everybody.

If you want to donate to the author then you can buy me a coffee.