Generate minecraft maps of real locations using UK LIDAR data (laser scans of terrain) and information from OpenStreetMap.
This software uses Perl and is dependent on the following module:
- Archive::Zip
You'll need to ensure those are installed before using the software. To check you can use:
perl -MArchive::ZIP -e 'print "OK\n";'
Which will say "OK" if it's installed, and otherwise will report an error.
The generate-world
command is used to create your minecraft world. It provides
a number of options for customising the location of the world and how it is
generated.
Internet access is essential at all times whilst generating a world as it will be downloading lots of data.
The following generates a minecraft world called "Highfield" which will be stored
in the /saves/subdirectory
. It's centred on
a postcode in Southampton and will be 1km square (1000 blocks wide, 500 blocks either side
of the central point)
./generate-world --postcode SO171BJ --size 1000 Highfield
It's recommended that while you are testing that you generate smaller worlds. Obviously the larger the map, the longer it will take to generate.
You may find it handy to symlink the /saves/ directory to your minecraft saves location.
You can also generate the map in a different location using the --saves
option:
./generate-world --saves /path/to/.minecraft/saves --postcode SO171BJ --size 1000 Highfield
If a world of the given name already exists then the script will refuse to overwrite it.
Use the --replace
option to force overwriting of an existing world. Again, useful
whilst testing your configuration:
./generate-world --replace --postcode SO171BJ --size 1000 Highfield
Instead of a postcode you can specify the central point of the map using a specific
location. You can use either an easting and northing, or a latitude and longitude.
By default the script assumes you're providing easting and northing, but the
--ll
allows you to switch:
./generate-world --centre 375046,164145 --size 1000 Highfield
./generate-world --ll --centre 51.375801,-2.3599039 --size 1000 Highfield
The generation of the world can be customised by tweaking the configuration
given in the config
directory. It's possible to override these to use different
configuration files using the --blocks
and --colours
parameters.
For example in Bath you may want to use sandstone instead of brick for generating
buildings. The blocks.winter
and blocks.nether
configure allow you to
generate worlds winter biome or as part of the nether.
The blocks.hollow
config generates hollow buildings. It's worth using but
takes much longer to generate a world.
You must use either postcode with size, centre with size or specify a from & to. You must always specify the name of the world to save.
- --saves
mc-saves-dir
:: Optional. Specify location of Minecraft /saves/ directory. - --ll :: Option to indicate that the cordinates are in lat,long (rather than UK easting/northing).
- --postcode
postcode
:: the UK postcode to centre on. - --centre
x
,y
:: the centre of the map to create (instead of using a postcode) - --size
n
:: size of a square map. - --size
w
,h
:: size of a rectangular map. - --replace :: delete the existing minecraft world and replace it.
- --yshift
n
:: move the world vertically up or down. Useful for districts very high above sealevel. - --flood
n
:: air blocks between this height and sealevel will be made into water instead, simulating sea-level rise. - --elevation
plugin
:: use an alternate elevation plugin. Default is UKDefra. Alternate is Flat (for no LIDAR data). - --blocks
file
:: use an alternate file to decide how to render blocks. --blocks config/blocks.hollow makes hollow buildings, at a cost of speed. - --colours
file
:: use an alternate file to interpret colours in open streetmap tiles. - --rotate
degrees
:: rotate the map (90 degrees is a one-quarter rotation. This option is a bit messy still and the origin of rotation is something weird. - --scale
factor
:: make the world larger or smaller. By default one Minecraft block is one real-world block. If you use --scale 0.1 then every Minecraft block will represent 10 real world metres. - --mapzoom
zoom
:: use a different level of detail from open streetmap. Outside cities this should be lowered to avoid forcing open street map to generate high resultion tiles of empty space. Be a good citizen! - --tiles
tile-pattern
:: use an alternate map tile server. - --grid
projection
:: use an alternate map projection. Default is OSGB36 for UK stuff. For anywhere else, use --grid MERC (combined with --elevation Flat)
This software is provided under the GPLv3. Please feel free to alter and share it.
This version was written by Christopher Gutteridge at the University of Southampton. (c) 2015-2017 Christopher Gutteridge
LIDAR data (c) Defra under the Open Government License. Map data (c) Open Streetmap Contributors under Creative Commons Attribution ShareAlike License.
Github: https://github.com/cgutteridge/geocraft Facebook: https://www.facebook.com/magic.minecraft.map.maker/
Author contact info: Email: [email protected] Twitter: cgutteridge
- http://www.chunkmapper.com/ Chunkmapper builds 1:30 scale maps with buildings and rail
- https://www.ordnancesurvey.co.uk/blog/tag/minecraft/ The UK Ordnace Survey has made a scale map of the whole country