xx0x/gbpxl

An invisible interface between Game Boy Camera and ESC/POS compatible printers.

gbpxl

Game Boy Printer XL

An invisible interface between Game Boy Camera and ESC/POS compatible printers with RS232 serial interface. There was a kit at Tindie but currently it's sold out. Improvements, suggestions, experience with various printer models are welcome!

Introduction video

How to use it

Build your gbpxl using kit (see below).

or

Download the code from this repository and build it yourself using Arduino Nano Every and TTL-RS232 converter. See the schematic folder for the breadboard design.

gbpxl kit

Kit (SOLD OUT):

https://www.tindie.com/products/xx0x/gbpxl-game-boy-printer-xl-kit/

Build instructions:

https://github.com/xx0x/gbpxl/blob/master/build-instructions/BUILD_INSTRUCTIONS.md

Gerber file and BOM are available here, if you want to make your own PCBs:

https://github.com/xx0x/gbpxl/tree/master/schematic-bom-pcb

How it looks:

Tested with these printers

Originally intended only for Epson TM-T88 family, but it should work with most ESC/POS printers by selecting different DIP settings.

Printer	DIP3	DIP4
Epson TM-T88III	OFF	ON
Epson TM-T88IV	ON	ON
Wincor Nixdorf TH230	ON	OFF
HPRT PPTII-A	OFF	OFF

gbpxl DIP switch settings

	DIP1: Scale	DIP2: Cut	DIP3: Baud rate	DIP4: Method
ON	3x	Yes	38400	GS
OFF	2x	No	9600	ESC *

Scale

• 2x scale is intended for 58 mm thermal printers
• 3x scale is intended for 80 mm thermal printers

Cut

Cuts the paper after printing each photo. (Some cheaper printers don't support it.)

Baud rate

Must be the same as selected by the printer (see the manual). If you are not sure, try 9600.

• Epson TM-T88 family: DIP switches under metal cover on the bottom.
• Wincor Nixdorf TH230: Selected in the menu (the menu is activated by holding Feed button while powering the printer on).

GS method

• "Gs v 0" if baudrate 9600
• "Gs ( L" if baudrate 38400

How to wire the board

The link cable contains VCC as well, so in theory it could be used to power gbpxl. But in reality, the provided voltage/current is not enough to run gbpxl without issues, mostly since the MAX232 chip boosts TTL logic levels to higher voltages used by RS232 interface. That's why I decided to include buck regulator and power the device from printer's accessory port. If you want to power gbpxl directly with 5V, use VCC pad located in UPDI.

Game Boy Link Connector

Cable at the end which plugs into the Game Boy.

  ___________
 |  6  4  2  |                
  \_5__3__1_/     
                            
2. SO (serial output)       |  BROWN / GREEN*
3. SI (serial input)        |  GREEN / BROWN*
5. SC (serial clock)        |  BLUE*
6. GND                      |  RED*

*Color codes for cheap Game Boy Color link cable, which you can buy on eBay etc. GREEN/BROWN color are swapped in each cable - you must try both variants or use your multimeter.

RJ-12 connector (power from printer's "DK" port)

Cable at the end which plugs into the printer.

  ____===____
 |           |
 |___________|
  | | | | | |
  1 2 3 4 5 6 

4. VIN (24 V)
6. GND 

Gbpxl board supports 10-30 V as VIN voltage.

...if using Arduino Every

• SO = Arduino pin 4
• SI = Arduino pin 3
• SC = Arduino pin 2

Don't connect RJ-12 to Arduino Nano Every, it's VIN input supports 21 V max!

Programming gbpxl

Since gbpxl uses ATmega4809, the programming must be done via UPDI interface, you can't use just your regular USBasp or similar. The UPDI connector uses the pinout based on microUPDI project, which also includes TX/RX connections for easy communication with PC - useful for transfering images etc.

Sadly, since the UPDI is quite new, there are no cheap programmers available yet, but you can build the microUPDI or jtag2updi quite easily by yourself. When uploading, specify "Arduino Nano Every" as your pinout.

Don't forget to unplug the power before connecting UPDI, since the programmer usually powers the device!

Additional stuff

BTN

As you can see in the photos and in the schematic, gbpxl also includes a hidden button. It's not populated by default, since there was no space for a microswitch, but you can use tweezers or a wired button for more permanent solution. Its' function is to print the last photo (stored in the buffer) again. It's a useful feature for selecting various settings with DIP switches and for development - since you don't have to wait for the transfer between Game Boy and gbpxl.

If you trigger the button when nothing has been printed yet, it will print the photo of the gbpxl author (stored in test_image_custom_frame.h) :-)

LED

The LED may look kind of useless, since it's hidden inside the case, but it's useful for development and problem solving with data transfer, since it blinks when recieving or sending data. If you want, you can always drill a hole in the plastic connector case to see the LED blinking...

Author

Václav Mach

• http://www.xx0x.cz
• http://www.vaclav-mach.cz

Thanks!

Big thanks to Brian Khuu for decoding the GBP protocol and making Arduino Game Boy Printer Emulator https://github.com/mofosyne/arduino-gameboy-printer-emulator

gbpxl's Issues

Would this Printer work with gbpxl?

It claims to support RS232 but it only has a connector for 5 pins on the back,

https://www.aliexpress.com/item/1005004100796991.html

Update the emulator to v2

Hi!

Your project it's amazing! I adapted some parts to make it work for cheap Bluetooth thermal printers using a ESP32 (its uploaded to my git), but, i noticed that you are using code from the v1 of Bryan's emulator, so, the printing from the GB it's slow
Do you have any plans to update your code?
Greets from Mexico!