- 不要用 root 用户 git 和编译!!!
- 国内用户编译前最好准备好梯子
- 默认登陆IP 192.168.2.1, 密码 无
- 免责声明:本人不欢迎例如 nobk 这种**使用或者访问本源代码哪怕一个字节,否则一旦他家里因此而发生各种全家富贵的情况,与本人一律无关
-
首先装好 Ubuntu 64bit,推荐 Ubuntu 20.04 LTS x64
-
命令行输入
sudo apt-get update
,然后输入
sudo apt-get -y install build-essential asciidoc binutils bzip2 gawk gettext git libncurses5-dev libz-dev patch python3 python2.7 unzip zlib1g-dev lib32gcc1 libc6-dev-i386 subversion flex uglifyjs git-core gcc-multilib p7zip p7zip-full msmtp libssl-dev texinfo libglib2.0-dev xmlto qemu-utils upx libelf-dev autoconf automake libtool autopoint device-tree-compiler g++-multilib antlr3 gperf wget curl swig rsync aria2 ca-certificates python3-pyelftools python-pyelftools
-
使用
git clone https://github.com/coolsnowwolf/lede
命令下载好源代码,然后cd lede
进入目录 -
./scripts/feeds update -a ./scripts/feeds install -a make menuconfig
-
make -j8 download V=s
下载dl库(国内请尽量全局科学上网) -
输入
make -j1 V=s
(-j1 后面是线程数。第一次编译推荐用单线程)即可开始编译你要的固件了。
本套代码保证肯定可以编译成功。里面包括了 R21 所有源代码,包括 IPK 的。
二次编译:
cd lede
git pull
./scripts/feeds update -a && ./scripts/feeds install -a
make defconfig
make -j8 download
make -j$(($(nproc) + 1)) V=s
如果需要重新配置:
rm -rf ./tmp && rm -rf .config
make menuconfig
make -j$(($(nproc) + 1)) V=s
编译完成后输出路径:bin/targets
-
DO NOT USE ROOT USER TO CONFIGURE!!!
-
Login IP is 192.168.1.1 and login password is "password".
First, you need a computer with a linux system. It's better to use Ubuntu 18 LTS 64-bit.
Next you need gcc, binutils, bzip2, flex, python3.5+, perl, make, find, grep, diff, unzip, gawk, getopt, subversion, libz-dev and libc headers installed.
To install these program, please login root users and type
sudo apt-get -y install build-essential asciidoc binutils bzip2 gawk gettext git libncurses5-dev libz-dev patch python3.5 python2.7 unzip zlib1g-dev lib32gcc1 libc6-dev-i386 subversion flex uglifyjs git-core gcc-multilib p7zip p7zip-full msmtp libssl-dev texinfo libglib2.0-dev xmlto qemu-utils upx libelf-dev autoconf automake libtool autopoint device-tree-compiler g++-multilib antlr3 gperf wget swig rsync aria2
in terminal
Third, logout of root users. And type this git clone https://github.com/coolsnowwolf/lede
in terminal to clone this source.
After these please type cd lede
to cd into the source.
Please Run ./scripts/feeds update -a
to get all the latest package definitions
defined in feeds.conf
/ feeds.conf.default
respectively
and ./scripts/feeds install -a
to install symlinks of all of them into
package/feeds/
.
Please use make menuconfig
to choose your preferred
configuration for the toolchain and firmware.
Use make menuconfig
to configure your image.
Simply running make
will build your firmware.
It will download all sources, build the cross-compile toolchain,
the kernel and all chosen applications.
To build your own firmware you need to have access to a Linux, BSD or MacOSX system (case-sensitive filesystem required). Cygwin will not be supported because of the lack of case sensitiveness in the file system.
GPLv3 is compatible with more licenses than GPLv2: it allows you to make combinations with code that has specific kinds of additional requirements that are not in GPLv3 itself. Section 7 has more information about this, including the list of additional requirements that are permitted.
由于wsl的PATH路径中包含带有空格的Windows路径,有可能会导致编译失败,请在将make -j1 V=s或make -j$(($(nproc) + 1)) V=s改为
首次编译:
PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin make -j1 V=s
二次编译:
PATH=/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin make -j$(($(nproc) + 1)) V=s
-
源代码中绝不含任何后门和可以监控或者劫持你的 HTTPS 的闭源软件, SSL 安全是互联网最后的壁垒。安全干净才是固件应该做到的;
-
如有技术问题需要讨论,欢迎加入 QQ 讨论群: OP 共享技术交流群 ,号码 297253733 ,加群链接: 点击链接加入群聊【 OP 共享技术交流群】:点击加入
-
想学习 OpenWrt 开发,但是摸不着门道?自学没毅力?基础太差?怕太难学不会?跟着佐大学 OpenWrt 开发入门培训班助你能学有所成 报名地址:点击报名
1.在软件包的Makefile中让此项写成这样PKG_MIRROR_HASH:=skip (如果不加上skip,那么在第三步填充哈希值时会直接删除"PKG_MIRROR_HASH:="这一行)
2.下载软件包(如软件包名为hello,包的Makefile放在package/network/services/hello下)
make package/network/services/hello/download V=s
3.填充哈希值
make package/network/services/hello/check FIXUP=1 V=s
-
首先在软件包的Makefile中让此项空着(PKG_MIRROR_HASH:=),然后将整个openwrt系统进行编译make -j10
-
在第一步完成之后会在dl目录下发现一个新模块相关的压缩包,直接使用以下命令来生成哈希值,如:sha256sum 包名.tar.xz
-
将第二步生成的哈希值填充到Makefile的PKG_MIRROR_HASH即可